The driver side squib circuit consists of the airbag sensor assembly, spiral cable sub-assembly and horn button assembly.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side squib circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1800/51 | Short in Driver Side Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal 5 times in the driver side squib circuit during the primary check.
·
A horn button assembly malfunction.
·
A spiral cable sub-assembly malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
Instrument panel wire
·
Spiral cable sub-assembly
·
Horn button assembly
·
Airbag sensor assembly |
| B1801/51 | Open in Driver Side Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects an open circuit signal in the driver side squib circuit for 2 seconds.
·
A horn button assembly malfunction.
·
A spiral cable sub-assembly malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
Instrument panel wire
·
Spiral cable sub-assembly
·
Horn button assembly
·
Airbag sensor assembly |
| B1802/51 | Short to GND in Driver Side Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.
·
A horn button assembly malfunction.
·
A spiral cable sub-assembly malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
Instrument panel wire
·
Spiral cable sub-assembly
·
Horn button assembly
·
Airbag sensor assembly |
| B1803/51 | Short to B+ in Driver Side Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.
·
A horn button assembly malfunction.
·
A spiral cable sub-assembly malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
Instrument panel wire
·
Spiral cable sub-assembly
·
Horn button assembly
·
Airbag sensor assembly |
When installing the spiral cable sub-assembly and steering wheel, be sure to adjust the spiral cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the battery
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag sensor assembly, refer to initialization.*
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
*: w/ VSC
To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Turn the ignition switch off.
| *1 | Driver Side Squib | *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly | *4 | Connector G |
| *5 | SST | - | - |
| *a | Front view of wire harness connector (to Horn Button Assembly) |
*b | Color: Orange |
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the horn button assembly.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector G (orange connector).
Never connect the tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output |
| DTC B1800/51, B1801/51, B1802/51 or B1803/51 is output |
Codes other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector G.
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output
for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD (for Type A)>REMOVAL
for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD (for Type B)>REMOVAL
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is output
Disconnect the connector from the airbag sensor assembly.
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
Check that the connectors (on the airbag sensor assembly side and horn button assembly side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Connector G |
| *a | Front view of wire harness connector (to Horn Button Assembly) |
| *b | Color: Orange |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z2-2 (D+) - Body ground | Ignition switch ON | Below 1 V |
| z2-1 (D-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-2 (D+) - z2-1 (D-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-2 (D+) - z2-1 (D-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-2 (D+) - Body ground | Always | 1 MΩ or higher |
| z2-1 (D-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
Connect the connectors to the horn button assembly and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output |
| DTC B1800/51, B1801/51, B1802/51 or B1803/51 is output |
Codes other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is output
Disconnect the instrument panel wire connector from the spiral cable sub-assembly.
| *1 | Horn Button Assembly | *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly | *4 | Instrument Panel Wire |
| *5 | Cowl Wire | *6 | Connector E |
| *a | Rear view of wire harness connector (to Spiral Cable Sub-assembly) |
- | - |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L29-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| L29-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L29-1 (D+) - L29-2 (D-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L29-1 (D+) - L29-2 (D-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L29-1 (D+) - Body ground | Always | 1 MΩ or higher |
| L29-2 (D-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel wire connector from the cowl wire.
| *A | for LHD | *B | for RHD |
| *1 | Horn Button Assembly | *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly | *4 | Instrument Panel Wire |
| *5 | Cowl Wire | *6 | Connector C |
| *a | Front view of wire harness connector (to Instrument Panel Wire) |
- | - |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| IL4-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| IL4-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| IL7-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| IL7-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IL4-1 (D+) - IL4-2 (D-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IL7-1 (D+) - IL7-2 (D-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IL4-1 (D+) - IL4-2 (D-) | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IL7-1 (D+) - IL7-2 (D-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IL4-1 (D+) - Body ground | Always | 1 MΩ or higher |
| IL4-2 (D-) - Body ground | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IL7-1 (D+) - Body ground | Always | 1 MΩ or higher |
| IL7-2 (D-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG