Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID TRANSAXLE OIL SEAL
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0442245 HYBRID TRANSAXLE OIL SEAL A

Q710 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear drive shat oil seal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

* The vehicle height changes because of suspension or tire replacement.

Replaced Part or PerformedProcedure Necessary Procedure Effect/Inoperative Functionwhen Necessary Procedurenot Performed Link
·

Rear disc (Including removal and installation)

·

Parking brake shoe (Including removal and installation)

·

Parking brake actuator assembly with bracket (Removed and installed)


Parking brake bedding Electric parking brake system (Click here)
Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust sttering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)

PROCEDURE

Hide 42340D 2.REMOVE REAR DRIVE SHAFT OIL SEAL LH

a.
C428287N02
1.115,2.688 1.417,3.083 1.417,3.083 1.5,3.083 false 1.563,3.01 2.021,3.208 0.458,0.198 10 false SST

Using SST, remove the rear drive shaft oil seal LH from the FCV with motor transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the FCV with motor transaxle assembly.



Hide 42330G 3.REMOVE REAR DRIVE SHAFT OIL SEAL RH

a.
C428288N02
1.833,2.604 2.302,2.604 false 1.563,2.531 1.958,2.719 0.396,0.188 10 false SST

Using SST, remove the rear drive shaft oil seal RH from the FCV with motor transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the FCV with motor transaxle assembly.



Hide 42330G 4.INSTALL REAR DRIVE SHAFT OIL SEAL RH

a.
C428289C01
2.208,1.073 2.375,1.073 2.375,1.073 2.375,0.719 false 2.198,0.906 2.281,0.906 2.281,0.906 2.281,0.74 false 2.385,0.26 2.698,0.417 0.313,0.156 10 false *a 2.031,0.802 2.26,1 0.229,0.198 10 false *b 2.031,0.979 2.344,1.135 0.313,0.156 10 false *c
*a Depth
*b Inner Lip
*c Outer Lip


Using SST and a hammer, install a new rear drive shaft oil seal RH to the FCV with motor transaxle assembly.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the rear drive shaft oil seal RH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the rear drive shaft oil seal RH.

·

Do not install the rear drive shaft oil seal RH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the rear drive shaft oil seal RH.




Hide 42340D 5.INSTALL REAR DRIVE SHAFT OIL SEAL LH

a.
C428290C02
2.188,2.135 2.625,2.823 2.625,2.823 1.75,2.24 true 1.229,0.969 1.385,0.969 1.385,0.969 1.385,0.521 false 1.167,0.75 1.281,0.75 1.281,0.75 1.281,0.5 false 2.656,2.75 3.01,2.958 0.354,0.208 10 false SST 1.458,0.292 1.76,0.521 0.302,0.229 10 false *a 1.052,0.885 1.354,1.115 0.302,0.229 10 false *b 1,0.656 1.302,0.885 0.302,0.229 10 false *c
*a Depth
*b Inner Lip
*c Outer Lip


Using SST and a hammer, install a new rear drive shaft oil seal LH to the FCV with motor transaxle assembly.

SST
09649-17010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the rear drive shaft oil seal LH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the rear drive shaft oil seal LH.

·

Do not install the rear drive shaft oil seal LH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the rear drive shaft oil seal LH.