Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448240 HEADLIGHT ASSEMBLY A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E462996N01
5.74,2.333 6.76,2.51 1.021,0.177 0.938,2.719 1.271,2.719 false 5.479,2.417 5.729,2.417 false 4.833,0.375 5.094,0.375 5.094,0.375 5.094,0.615 false 5.583,1.875 6.031,1.875 false 6.156,0.24 6.604,0.24 false 6.063,0.698 5.75,0.698 false 0.74,2.573 1.021,2.927 0.281,0.354 18 false 3 6.479,1.729 6.76,2.083 0.281,0.354 18 false 1 6.094,0.583 6.375,0.938 0.281,0.354 18 false 2 5.729,1.344 6.188,1.542 0.458,0.198 10 false x 3 5.813,2.365 6.792,2.521 0.979,0.156 8 false 7.0 (71, 62 in.*lbf) 5.719,0.125 6.677,0.5 0.958,0.375 18 false 4, 5 4.354,0.781 4.813,0.979 0.458,0.198 10 false x 2 4.635,0.323 5.094,0.521 0.458,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HEADLIGHT ASSEMBLY LH - (Click here) - -
2 FRONT UPPER FENDER PROTECTOR LH 53826A - - -
3 FRONT BUMPER ASSEMBLY - - - -
4 PERFORM SYSTEM CALIBRATION - - - (Click here)
5 ADJUST HEADLIGHT AIMING - - - (Click here)

*1 CENTER HOOD CUSHION - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1.INSTALL HEADLIGHT ASSEMBLY LH

a.
E457901C01
0.469,0.323 0.896,0.688 0.427,0.365 18 false i 4.104,0.333 4.552,0.656 0.448,0.323 18 true ii,iii
V113146

Place Hand Here
V113147

Install in this Direction (1)
V113148

Install in this Direction (2) - -


i.

Set the headlight assembly LH in the installation direction (1) as shown in the illustration.


ii.

Slide the headlight assembly LH in the installation direction (2) and attach the guide.


iii.

Place your hands at the positions shown in the illustration and set the bracket to the screw seat.

NOTICE:

Do not break the bracket.




b.
E462998C01
0.438,0.385 0.594,0.583 0.156,0.198 18 true i 4.188,0.417 4.344,0.615 0.156,0.198 18 true ii
V100135

Bolt
V100136

Screw


i.

Install the headlight assembly LH with the bolt and 3 screws.

Torque:
Bolt : 7.0 N*m (71 kgf*cm, 62 in.*lbf)


ii.

Connect the connector and lock the connector lock lever and remove the protective tape.



Hide 53826A 2.INSTALL FRONT UPPER FENDER PROTECTOR LH

Hide 3.INSTALL FRONT BUMPER ASSEMBLY

Hide 4.PERFORM SYSTEM INITIALIZATION