Home › Vehicle Exterior › LIGHTING (EXT) › SWITCH HOUSING
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448248 SWITCH HOUSING A

LIGHTING (EXT)  SWITCH HOUSING  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E463009N01
5.896,0.615 5.531,0.615 false 3.604,2.448 3.604,1.802 false 1.854,2.198 1.854,1.885 false 5.427,2.719 6,2.719 false 6.083,2.583 6.365,2.938 0.281,0.354 18 false 1 1.802,2.24 2.083,2.594 0.281,0.354 18 false 3 6.292,0.49 6.573,0.844 0.281,0.354 18 false 2 3.531,2.5 3.813,2.854 0.281,0.354 18 false 4 0.969,1.938 1.25,2.292 0.281,0.354 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY 84306 - - -
2 WINDSHIELD WIPER SWITCH ASSEMBLY 84650 (Click here) - -
3 TURN SIGNAL SWITCH 84329 (Click here) - -
4 STEERING WHEEL SWITCH HOUSING 84319 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering wheel switch housing removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Steering sensor (Including removal and installation) Steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 84650 2.REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY

Z101186

Click here(Click here)

Hide 84329 3.REMOVE TURN SIGNAL SWITCH

Z101186

Click here(Click here)

Hide 84319 4.REMOVE STEERING WHEEL SWITCH HOUSING

a.
E458626C01
0.604,0.104 0.885,0.458 0.281,0.354 18 false i 4.021,0.094 4.219,0.365 0.198,0.271 18 true ii
V113147

Remove in this Direction - -


i.

Using pliers, loosen and hold the plastic tie clamp.


ii.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the steering wheel switch housing as shown in the illustration.