Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0448369 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B593225N02
6.104,2.25 7.083,2.448 0.979,0.198 6.073,2.198 7.115,2.51 1.042,0.313 2.51,1.677 2.99,1.677 false 6.375,0.5 6.854,0.5 false 6.385,0.167 6.896,0.167 false 5.01,1.948 5.563,1.948 false 6.104,2.354 5.74,2.354 false 6.385,0.802 6.865,0.802 false 6.198,0.031 6.479,0.385 0.281,0.354 18 false 5 6.198,0.375 6.479,0.729 0.281,0.354 18 false 3 3.094,1.573 3.375,1.927 0.281,0.354 18 false 2 5.771,1.844 6.052,2.198 0.281,0.354 18 false 1 6.167,2.271 7.156,2.49 0.99,0.219 8 false 9.0 (92, 80 in.*lbf) 5.948,0.667 6.458,1.021 0.51,0.354 18 false 4, 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT AIRBAG SENSOR LH 89174A (Click here) - -
2 HEADLIGHT ASSEMBLY LH - - - -
3 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)
5 CHECK SRS WARNING LIGHT - (Click here) - -
6 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

CAUTION / NOTICE / HINT

PROCEDURE

Hide 89174A 1.INSTALL FRONT AIRBAG SENSOR LH

a.
B605562C01
1.042,0.458 1.833,0.458 true 0.458,0.104 0.74,0.458 0.281,0.354 18 false i 4.49,0.156 4.771,0.51 0.281,0.354 18 false ii 0.813,0.375 1.042,0.604 0.229,0.229 10 true *a
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B593226N02
2.063,0.958 2.229,1.26 0.167,0.302 18 true i 2.26,2.063 2.542,2.344 0.281,0.281 18 true iv 1.375,0.375 1.542,0.656 0.167,0.281 18 true ii 3.917,0.094 4.198,0.375 0.281,0.281 18 true iii

i.

Attach the claw to hold the front airbag sensor LH in place.


ii.

Install the front airbag sensor LH with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the front airbag sensor LH has been dropped, replace it with a new one.

·

When installing the front airbag sensor LH, be careful that the SRS wiring does not interfere with or is not pinched between other parts.




iii.

Check that there is no looseness in the installation parts of the front airbag sensor LH.


iv.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR




Hide 2.INSTALL HEADLIGHT ASSEMBLY LH

Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4. PERFORM DIAGNOSTIC SYSTEM CHECK

Hide 6. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART