Before performing pre-disposal deployment of any pop up hood lifter, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.
Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.
If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.
When scrapping a vehicle equipped with an SRS or disposing of the curtain shield airbag assembly LH LH, be sure to deploy the airbag first in accordance with the following procedure. If any abnormality occurs with the airbag deployment, contact the Service Department of the distributor.
53470
2.DISPOSE OF POP UP HOOD LIFTER ASSEMBLY LH (When Installed in Vehicle)
When disposing of a pop up hood lifter assembly LH, use an unneeded vehicle to deploy the pop up hood lifter assembly LH.
Be sure to observe the following procedure when deploying the pop up hood lifter assembly LH.
Prepare a battery as the power source to deploy the pop up hood lifter assembly LH.
Check the function of SST.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL
Refer to Precaution.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>PEDESTRIAN PROTECTION SYSTEM>PRECAUTION
Disconnect the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Remove the front fender reinforcement top sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL
Disconnect pop up hood lifter connector.
When disconnecting any pop up hood lifter connector, take care not to damage the wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
Install SST.
Connect SST to the pop up hood lifter assembly LH connector.
Do not deploy if the pop up hood lifter assembly LH is loose.
If deployed while the pop up hood lifter assembly LH is loose, the pop up hood lifter assembly LH may fly off and cause serious injuries.
Connect SST together (09082-00700 and 09082-00820).
To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock.
| *a | 10 m (32.8 ft.) or more |
Move SST at least 10 m (32.8 ft.) away from the engine compartment of the vehicle.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Close the engine hood.
Check that the engine hood is locked.
Deploy the pop up hood lifter assembly LH.
Check that no one is within a 10 m (32.8 ft.) radius of the vehicle.
Press SST activation switch to deploy the pop up hood lifter assembly LH.
Do not deploy with people inside or around the vehicle.
If deployed with people inside or around the vehicle, serious injuries may occur.
The pop up hood lifter assembly LH is deployed as the LED of SST activation switch comes on.
Remove the pop up hood lifter assembly LH.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>POP UP HOOD LIFTER>REMOVAL
The pop up hood lifter assembly LH becomes extremely hot when the pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.
If not left alone for 30 minutes or more, burns may occur when touched.
Do not apply water etc. to a pop up hood lifter assembly LH with a deployed pop up hood lifter assembly LH.
If water is applied to the pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.
Always wear safety glasses and gloves when handling a deployed pop up hood lifter assembly LH.
If the pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
After removal, quickly seal the pop up hood lifter assembly LH in a plastic bag.
Place the pop up hood lifter assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.
The pop up hood lifter assembly LH becomes extremely hot when the pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.
If not left alone for 30 minutes or more, burns may occur when touched.
Do not apply water etc. to a pop up hood lifter assembly LH with a deployed pop up hood lifter assembly LH.
If water is applied to the pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.
Always wear safety glasses and gloves when handling a deployed pop up hood lifter assembly LH.
If the pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
Never dispose of a pop up hood lifter assembly LH with an undeployed pop up hood lifter assembly LH.
If an undeployed pop up hood lifter assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.
Always wash your hands with water after completing the operation.
53470
3.DISPOSE OF POP UP HOOD LIFTER ASSEMBLY LH (When not Installed in Vehicle)
Be sure to observe the following procedure when deploying the pop up hood lifter assembly LH.
Prepare a battery as the power source to deploy the pop up hood lifter assembly LH.
Check the function of SST.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL
Refer to Precaution.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>PEDESTRIAN PROTECTION SYSTEM>PRECAUTION
Disconnect the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Remove the pop up hood lifter assembly LH.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>POP UP HOOD LIFTER>REMOVAL
| *1 | Pop Up Hood Cover |
Remove the pop up hood cover.
Install SST.
Connect SST to the pop up hood lifter assembly LH.
| *a | Wire Diameter |
|
Stripped Wire |
Using braided wire, tie down the pop up hood lifter assembly LH to an unneeded tire.
Cross-sectional area of stripped wire
1.25 mm2 (0.0019 in.2) or more
If the wire is too thin or an alternative object is used to tie down the pop up hood lifter assembly LH, it may snap when the pop up hood lifter assembly LH is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2 (0.0019 in.2).
To calculate the area of the cross-sectional area of stripped wire:
Cross sectional area = 3.14 x (Diameter)2 / 4
| *a | Width |
| *b | Inner Diameter |
| *c | extended section |
Position the pop up hood lifter assembly LH inside the tire as shown in the illustration.
Must exceed the following dimensions
185 mm (7.28 in.)
360 mm (1.18 ft.)
| *a | Extended Section |
| *b | Remove looseness |
Do not install the pop up hood lifter assembly LH with the extended section facing outside.
When securing the pop up hood lifter assembly LH, make sure there is no looseness in the wire harness.
If the extended section is facing outside or the wire harness is loosely wrapped, the deployed pop up hood lifter assembly LH and tire may fly off and cause serious injuries.
The tire may be damaged by the pop up hood lifter assembly LH deployment, so use unneeded tire.
Through the wire to pop up hood lifter installation hole.
Place the tires.
| *a | Tires (2 or more) |
Place at least 2 tires under the tire to which the pop up hood lifter assembly LH is tied.
Place at least 2 tires onto the tire to which the pop up hood lifter assembly LH is tied. The top tire should have a wheel installed.
Do not place SST connector under the tire because it could be damaged.
The wheel and tires may be damaged by the pop up hood lifter assembly LH deployment, so use an unneeded wheel and tires.
Tie the tires together with 2 wires.
Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the pop up hood lifter assembly LH is deployed.
Install SST.
| *a | 10 m (32.8 ft.) or more |
Connect SST together (09082-00700 and 09082-00820).
To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.
Move SST at least 10 m (32.8 ft.) away from the pop up hood lifter assembly LH tied down to the tire.
Deploy the pop up hood lifter assembly LH.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the pop up hood lifter assembly LH is tied.
Press SST activation switch to deploy the pop up hood lifter assembly LH.
Do not deploy with people around the tire.
If deployed with people around the tire, serious injuries may occur.
The pop up hood lifter assembly LH is deployed as the LED of SST activation switch comes on.
Dispose of the pop up hood lifter assembly LH.
The pop up hood lifter assembly LH becomes extremely hot when the pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.
If not left alone for 30 minutes or more, burns may occur when touched.
Do not apply water etc. to a pop up hood lifter assembly LH with a deployed pop up hood lifter assembly LH.
If water is applied to the pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.
Always wear safety glasses and gloves when handling a deployed pop up hood lifter assembly LH.
If the pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
Never dispose of a pop up hood lifter assembly LH with an undeployed pop up hood lifter assembly LH.
If an undeployed pop up hood lifter assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.
Always wash your hands with water after completing the operation.
Remove the pop up hood lifter assembly LH from the tire.
Place the pop up hood lifter assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.