Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2020.11–2021.08
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448416 LIGHTING SYSTEM U

LIGHTING (EXT)  LIGHTING SYSTEM  TERMINALS OF ECU  


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E453982C01
1.083,3.198 1.49,3.458 0.406,0.26 3.24,3.198 3.646,3.458 0.406,0.26 5.448,3.208 5.854,3.469 0.406,0.26 3.24,7.708 3.646,7.969 0.406,0.26 1.823,4.542 2.229,4.802 0.406,0.26 5.385,4.479 5.792,4.74 0.406,0.26 1.125,6.177 1.531,6.438 0.406,0.26 3.573,6.115 3.979,6.375 0.406,0.26 6.25,6.146 6.656,6.406 0.406,0.26 5.271,6.146 5.677,6.406 0.406,0.26 1.625,1.781 1.906,1.781 false 1.625,1.427 1.906,1.427 false 1.625,1.115 1.906,1.115 false 1.573,0.604 1.573,0.24 1.573,0.24 1.781,0.24 false 1.99,1.729 2.302,1.927 0.313,0.198 10 false D14 1.979,1.063 2.292,1.26 0.313,0.198 10 false D12 1.99,1.375 2.302,1.573 0.313,0.198 10 false D11 3.75,0.927 3.906,1.125 0.156,0.198 10 false A 1.833,0.177 2.146,0.375 0.313,0.198 10 false *1 5.531,3.271 5.844,3.469 0.313,0.198 10 false D12 3.323,3.271 3.635,3.469 0.313,0.198 10 false D11 1.177,3.271 1.49,3.469 0.313,0.198 10 false D14 3.417,7.76 3.573,7.958 0.156,0.198 10 false A 0.833,1.031 1.146,1.229 0.313,0.198 10 false 4H 0.854,1.646 1.167,1.844 0.313,0.198 10 false 4F 0.854,2.01 1.167,2.208 0.313,0.198 10 false 4L 0.865,2.229 1.177,2.427 0.313,0.198 10 false 4K 5.823,1.042 6.135,1.24 0.313,0.198 10 false 4D 5.813,1.615 6.125,1.813 0.313,0.198 10 false 4A 1.958,4.615 2.271,4.813 0.313,0.198 10 false 4A 5.51,4.542 5.823,4.74 0.313,0.198 10 false 4D 1.271,6.24 1.583,6.438 0.313,0.198 10 false 4F 3.688,6.177 4,6.375 0.313,0.198 10 false 4H 6.417,6.208 6.729,6.406 0.313,0.198 10 false 4L 5.406,6.219 5.719,6.417 0.313,0.198 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect the instrument panel junction block assembly connectors.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A-32 (IG) - Body ground Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
A-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-11 (GND1) - Body ground Ground Always Below 1 Ω


c.

Install the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


d.

Measure the voltage and pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

D11-12 (HRY2) - Body ground H-LP RH relay drive output 15 seconds or more after ignition switch turned off Below 1 V
Ignition switch ON or within 15 seconds after ignition switch turned off 11 to 14 V
4B-29 - Body ground BKUP LP relay drive output Ignition switch off, shift lever not in R Below 1 V
Ignition switch ON, shift lever in R 11 to 14 V
4F-19 (HRLY) - Body ground*1 H-LP LH relay drive output 15 seconds or more after ignition switch turned off Below 1 V
Ignition switch ON or within 15 seconds after ignition switch turned off 11 to 14 V
4F-20 (HRLY) - Body ground*2 H-LP LH relay drive output 15 seconds or more after ignition switch turned off Below 1 V
Ignition switch ON or within 15 seconds after ignition switch turned off 11 to 14 V
D11-23 (CLTB) - G12-25 (CLTE) Automatic light control sensor power supply output Ignition switch ON 11 to 14 V
D11-24 (CLTS) - Body ground Automatic light control sensor signal input Ignition switch off Below 1 V
Ignition switch ON Pulse generation
(See waveform 1)
D11-26(AHBI) - Body ground Auto high beam switch signal input Auto high beam switch off 11 to 14 V
Auto high beam switch on Below 1 V
D14-21(AHID) - Body ground Auto high beam switch indicator drive output Ignition switch ON, auto high beam switch off 11 to 14 V
Ignition switch ON, auto high beam switch on Below 1 V
D11-16 (HEAD) - Body ground Light control switch in HEAD position signal input Light control switch in HEAD position Below 1 V
Light control switch not in HEAD position 11 to 14 V


e.
E302989E04
2.844,1.625 3.292,1.844 0.448,0.219 12 false GND

Waveform 1

Item Content
Terminal No. (Symbol) D11-24 (CLTS) - Body ground
Tool Setting 2 V/DIV., 10 ms./DIV.
Condition Ignition switch ON

HINT:

The communication waveform changes according to the surrounding brightness.




CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (w/ Adaptive High Beam System)


E457143N01
1.75,0.167 2.208,0.438 0.458,0.271 4.667,0.313 5.125,0.573 0.458,0.26 6.219,0.344 6.677,0.604 0.458,0.26 1.865,0.208 2.323,0.406 0.458,0.198 10 false A26 6.396,0.385 6.854,0.583 0.458,0.198 10 false C 4.833,0.354 5.292,0.552 0.458,0.198 10 false B

a.

Disconnect the A26 headlight ECU sub-assembly LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A26-4 (IG) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A26-13 (ECUB) - Body ground Power supply
·

15 seconds or more after ignition switch turned off

·

Taillights off


Below 1 V
·

Ignition switch ON or within 15 seconds after ignition switch turned off

·

Taillights on


11 to 14 V
A26-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the A26 headlight ECU sub-assembly LH connector.

HINT:
·

Since the A26 headlight ECU sub-assembly LH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.

·

Since the B and C headlight ECU sub-assembly RH connectors are connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A26-16 (SBR) - A26-15 (SGR) Rear height control sensor sub-assembly LH power supply Ignition switch off Below 1 V
Ignition switch ON 4.75 to 5.25 V
A26-17 (SHRL) - A26-15 (SGR) Rear height control sensor sub-assembly LH signal input Ignition switch ON, vehicle unloaded, vehicle stopped (value decreases as the front of the vehicle is raised)
A26-20 (LINL) - Body ground LIN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A26-21(LCL) - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A26-22(LCH) - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A26-23(CANL) - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A26-24(CANH) - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
B-2 - B-3 Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 10.69 to 15.34 V
B-10 - B-1 Daytime running lights/clearance lights power source Daytime running lights and clearance lights off Below 1 V
Daytime running lights and clearance lights on 11 to 14 V
B-16 - B-1 Daytime running lights/clearance lights control signal output Clearance lights off Below 1 V
Daytime running lights and clearance lights on Pulse generation
B-9 - B-17 Headlight leveling motor power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
C-6 - C-1 Light control LED ECU power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
C-3 - Body ground LIN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
C-13 - Body ground LIN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation



CHECK HEADLIGHT ECU SUB-ASSEMBLY RH (w/ Adaptive High Beam System)


E457143N02
1.75,0.167 2.208,0.438 0.458,0.271 4.667,0.313 5.125,0.573 0.458,0.26 6.219,0.344 6.677,0.604 0.458,0.26 1.854,0.208 2.313,0.406 0.458,0.198 10 false A27 6.396,0.385 6.854,0.583 0.458,0.198 10 false C 4.833,0.354 5.292,0.552 0.458,0.198 10 false B

a.

Disconnect the A27 headlight ECU sub-assembly RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A27-4 (IG) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A27-13 (ECUB) - Body ground Power supply Below 1 V
·

Ignition switch ON or within 15 seconds after ignition switch turned off

·

Taillights on


11 to 14 V
A27-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the A27 headlight ECU sub-assembly RH connector.

HINT:
·

Since the A27 headlight ECU sub-assembly RH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.

·

Since the B and C headlight ECU sub-assembly RH connectors are connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A27-20 (LINL) - Body ground LIN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A26-23(CANL) - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A26-24(CANH) - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
B-2 - B-3 Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 10.69 to 15.34 V
B-10 - B-1 Daytime running lights/clearance lights power source Daytime running lights and clearance lights off Below 1 V
Daytime running lights and clearance lights on 11 to 14 V
B-16 - B-1 Daytime running lights/clearance lights control signal output Clearance lights off Below 1 V
Daytime running lights and clearance lights on Pulse generation
B-9 - B-17 Headlight leveling motor power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
C-6 - C-1 Light control LED ECU power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
C-3 - Body ground LIN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
C-13 - Body ground LIN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation



CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (w/o Adaptive High Beam System)


E457144N01
2.156,0.156 2.646,0.396 0.49,0.24 5.531,0.271 6.021,0.51 0.49,0.24 2.292,0.198 2.75,0.396 0.458,0.198 10 false A26 5.74,0.313 6.198,0.51 0.458,0.198 10 false B

a.

Disconnect the A26 headlight ECU sub-assembly LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A26-4 (IG) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A26-13 (ECUB) - Body ground Power supply
·

15 seconds or more after ignition switch turned off

·

Taillights off


Below 1 V
·

Ignition switch ON or within 15 seconds after ignition switch turned off

·

Taillights on


11 to 14 V
A26-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the A26 headlight ECU sub-assembly LH connector.

HINT:
·

Since the A26 headlight ECU sub-assembly LH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.

·

Since the B and C headlight ECU sub-assembly RH connectors are connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A26-16 (SBR) - A26-15 (SGR) Rear height control sensor sub-assembly LH power supply Ignition switch off Below 1 V
Ignition switch ON 4.75 to 5.25 V
A26-17 (SHRL) - A26-15 (SGR) Rear height control sensor sub-assembly LH signal input Ignition switch ON, vehicle unloaded, vehicle stopped (value decreases as the front of the vehicle is raised)
A26-20 (LINL) - Body ground LIN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A26-23 (CANL) - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A26-24 (CANH) - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
B-4 - B-5 Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 10.69 to 15.34 V
B-10 - B-1 Daytime running lights/clearance lights control signal output Daytime running lights and clearance lights off Below 1 V
Daytime running lights and clearance lights on 11 to 14 V
B-16 - B-1 Daytime running lights/clearance lights control signal output Clearance lights off Below 1 V
Daytime running lights and clearance lights on Pulse generation
B-7 - B-17 Headlight leveling motor power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
B-8 - B-17 Headlight leveling motor output signal
·

Ignition switch ON and Low beam hedlight on

·

Vehicle stationary


Below 1 V
·

Ignition switch ON and Low beam hedlight on

·

Vehicle height changed and hold 3 second or more


11 to 14 V
B-20 - B-11 High beam headlights drive output High beam headlights off Below 1 V
High beam headlights on 11 to 14 V



CHECK HEADLIGHT ECU SUB-ASSEMBLY RH (w/o Adaptive High Beam System)


E457144N02
2.156,0.156 2.646,0.396 0.49,0.24 5.531,0.271 6.021,0.51 0.49,0.24 2.292,0.198 2.75,0.396 0.458,0.198 10 false A27 5.74,0.313 6.198,0.51 0.458,0.198 10 false B

a.

Disconnect the A27 headlight ECU sub-assembly RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A27-4 (IG) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A27-13 (ECUB) - Body ground Power supply
·

15 seconds or more after ignition switch turned off

·

Taillights off


Below 1 V
·

Ignition switch ON or within 15 seconds after ignition switch turned off

·

Taillights on


11 to 14 V
A27-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the A27 headlight ECU sub-assembly RH connector.

HINT:
·

Since the A27 headlight ECU sub-assembly RH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.

·

Since the B and C headlight ECU sub-assembly RH connectors are connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A27-23 (CANL) - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A27-24 (CANH) - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
B-4 - B-5 Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 10.69 to 15.34 V
B-10 - B-1 Daytime running lights/clearance lights control signal output Daytime running lights and clearance lights off Below 1 V
Daytime running lights and clearance lights on 11 to 14 V
B-16 - B-1 Daytime running lights/clearance lights control signal output Clearance lights off Below 1 V
Daytime running lights and clearance lights on Pulse generation
B-7 - B-17 Headlight leveling motor power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
B-8 - B-17 Headlight leveling motor output signal
·

Ignition switch ON and Low beam hedlight on

·

Vehicle stationary


Below 1 V
·

Ignition switch ON and Low beam hedlight on

·

Vehicle height changed and hold 3 second or more


11 to 14 V
B-20 - B-11 High beam headlights drive output High beam headlights off Below 1 V
High beam headlights on 11 to 14 V



CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH


B340248N32
4.698,0.406 5.125,0.688 0.427,0.281 3.438,0.198 3.865,0.479 0.427,0.281 4.813,0.469 5.125,0.667 0.313,0.198 10 false z28 3.542,0.271 3.854,0.469 0.313,0.198 10 false E7

a.

Disconnect the E7 front multiplex network door ECU RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E7-1 (GND) - Body ground Ground Always Below 1 Ω
E7-6 (BDR) - Body ground Power supply Ignition switch off 11 to 14 V


c.

Reconnect the E7 front multiplex network door ECU RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
z28-2 (B) - z28-12 (-) Door mirror footwell light signal
·

Ignition switch off

·

Turn the light control switch to the AUTO position

·

Cover the automatic light control sensor with a lightproof object

·

All door lock → all door unlock (operate wireless unlock or smart unlock)


Below 1 V



CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH


B340248N33
4.698,0.406 5.125,0.688 0.427,0.281 3.438,0.198 3.865,0.479 0.427,0.281 4.813,0.469 5.125,0.667 0.313,0.198 10 false z29 3.542,0.271 3.854,0.469 0.313,0.198 10 false E25

a.

Disconnect the E25 front multiplex network door ECU LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E25-1 (GND) - Body ground Ground Always Below 1 Ω
E25-6 (BDR) - Body ground Power supply Ignition switch off 11 to 14 V


c.

Reconnect the E25 front multiplex network door ECU LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
z29-2 (B) - z29-12 (-) Door mirror footwell light signal
·

Ignition switch off

·

Turn the light control switch to the AUTO position

·

Cover the automatic light control sensor with a lightproof object

·

All door lock → all door unlock (operate wireless unlock or smart unlock)


Below 1 V





CHECK NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU


Click herePower Source / Network>POWER DISTRIBUTION>POWER INTEGRATION SYSTEM>TERMINALS OF ECU