Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2020.11–2021.08
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448416 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2439  Headlight LH Circuit  B243A  Headlight RH Circuit  


DESCRIPTION

The headlight ECU sub-assembly supplies internally boosted voltage to the LED so that the current supplied to the LED is always maintained at a constant value.

These DTCs are also output when the headlight ECU sub-assembly detects malfunctions while monitoring the applied voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B2439 Headlight LH Circuit
Detection condition:

Ignition switch ON , low beam headlights illuminated


Malfunction status:
·

LED malfunction

·

Open/short in LED circuit


Malfunction duration:

10 seconds or more


·

Headlight unit LH

·

Headlight unit assembly LH

·

Headlight ECU sub-assembly LH


AFS A w/ Adaptive High Beam System
B243A Headlight RH Circuit
Detection condition:

Ignition switch ON , low beam headlights illuminated


Malfunction status:
·

LED malfunction

·

Open/short in LED circuit


Malfunction duration:

10 seconds or more


·

Headlight unit RH

·

Headlight unit assembly RH

·

Headlight ECU sub-assembly RH


AFS (Sub) A w/ Adaptive High Beam System

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B2439 Headlight LH Circuit
Detection condition:

Ignition switch ON , low beam headlights illuminated


Malfunction status:
·

LED malfunction

·

Open/short in LED circuit


Malfunction duration:

10 seconds or more


·

Headlight unit LH

·

Headlight unit assembly LH

·

Headlight ECU sub-assembly LH


HL AutoLeveling A w/o Adaptive High Beam System
B243A Headlight RH Circuit
Detection condition:

Ignition switch ON , low beam headlights illuminated


Malfunction status:
·

LED malfunction

·

Open/short in LED circuit


Malfunction duration:

10 seconds or more


·

Headlight unit RH

·

Headlight unit assembly RH

·

Headlight ECU sub-assembly RH


HL AutoLeveling (Sub) A w/o Adaptive High Beam System

WIRING DIAGRAM

w/ Adaptive High Beam System:


E361141E05
5.167,2.948 7.135,3.219 1.969,0.271 10 false B 2.542,2.708 4.615,3.021 2.073,0.313 10 false Headlight Unit Assembly 1.427,1.219 2.385,1.552 0.958,0.333 10 false Lo/Hi Beam 5.146,3.104 7.115,3.375 1.969,0.271 10 false Headlight ECU Sub-assembly 2.813,1.417 3.448,1.781 0.635,0.365 10 false 1 5.708,1.427 6.344,1.792 0.635,0.365 10 false 2 5.708,0.865 6.344,1.229 0.635,0.365 10 false 3 2.823,0.865 3.458,1.229 0.635,0.365 10 false 4 1.229,2.021 3.302,2.333 2.073,0.313 10 false D 1.229,2.167 3.302,2.479 2.073,0.313 10 false Headlight Unit


w/o Adaptive High Beam System:


E401934E03
5.167,2.948 7.135,3.219 1.969,0.271 10 false B 2.542,2.708 4.615,3.021 2.073,0.313 10 false Headlight Unit Assembly 1.458,1.208 2.417,1.542 0.958,0.333 10 false Lo Beam 5.146,3.104 7.115,3.375 1.969,0.271 10 false Headlight ECU Sub-assembly 2.813,1.417 3.448,1.781 0.635,0.365 10 false 1 5.615,1.427 6.25,1.792 0.635,0.365 10 false 4 5.604,0.865 6.24,1.229 0.635,0.365 10 false 5 2.823,0.865 3.458,1.229 0.635,0.365 10 false 4 1.229,2.021 3.302,2.333 2.073,0.313 10 false D 1.229,2.167 3.302,2.479 2.073,0.313 10 false Headlight Unit


CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>REGISTRATION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Adaptive High Beam System A
w/o Adaptive High Beam System B



A

2.CLEAR DTC

B

10.CLEAR DTC
2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Body Electrical > AFS (Sub) > Clear DTCs
50002 413
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

Pre-procedure1

a.

10 seconds elapse after turning the ignition switch to ON and illuminating the low beam headlights using the light control switch.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Body Electrical > AFS (Sub) > Trouble Codes
50001 413
Result:
Result Proceed to
Only B2439 for AFS is output A
Only B243A for AFS (Sub) is output B
None of the above conditions are met C



Malfunction Content System Relevant DTC
Headlight ECU sub-assembly LH AFS B2439 Headlight LH Circuit
Headlight ECU sub-assembly RH AFS (Sub) B243A Headlight RH Circuit

Post-procedure1

a.

None



A

4.CHECK HEADLIGHT UNIT ASSEMBLY LH

B

7.CHECK HEADLIGHT UNIT ASSEMBLY RH

C

4.CHECK HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.

Interchange the headlight unit assembly LH with RH and connect the connectors to them.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL



Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

5.CHECK HEADLIGHT UNIT ASSEMBLY LH
5.CHECK HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.

10 seconds elapse after turning the ignition switch ON and illuminating the low beam headlights using the light control switch.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2439 is not output A
B2439 is output B



Post-procedure1

a.

None



A

6.CHECK HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

6.CHECK HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.
E459081C02
1.448,0.094 1.854,0.427 0.406,0.333 1.521,1.896 1.927,2.229 0.406,0.333 1.625,0.188 1.781,0.385 0.156,0.198 10 false B 1.677,1.99 1.833,2.188 0.156,0.198 10 false D 0.583,0.146 0.896,0.302 0.313,0.156 10 false *a 0.594,2 0.906,2.156 0.313,0.156 10 false *b
*a Component without harness connected
(Headlight ECU Sub-assembly LH)
*b Component without harness connected
(Headlight Unit LH)


Remove the headlight unit LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - D-1 Always Below 1 Ω
B-3 - D-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

7.CHECK HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Interchange the headlight unit assembly RH with LH and connect the connectors to them.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL



Procedure1

a.

Clear the DTCs.

Body Electrical > AFS (Sub) > Clear DTCs
50002 413
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

8.CHECK HEADLIGHT UNIT ASSEMBLY RH
8.CHECK HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

10 seconds elapse after turning the ignition switch ON and illuminating the low beam headlights using the light control switch.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS (Sub) > Trouble Codes
50001 413
Result:
Result Proceed to
B243A is not output A
B243A is output B



Post-procedure1

a.

None



A

9.CHECK HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

9.CHECK HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight unit RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

a.
E459081C02
1.448,0.094 1.854,0.427 0.406,0.333 1.521,1.896 1.927,2.229 0.406,0.333 1.625,0.188 1.781,0.385 0.156,0.198 10 false B 1.677,1.99 1.833,2.188 0.156,0.198 10 false D 0.583,0.146 0.896,0.302 0.313,0.156 10 false *a 0.594,2 0.906,2.156 0.313,0.156 10 false *b
*a Component without harness connected
(Headlight ECU Sub-assembly LH)
*b Component without harness connected
(Headlight Unit LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - D-1 Always Below 1 Ω
B-3 - D-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

10.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC

Pre-procedure1

a.

10 seconds elapse after turning the ignition switch to ON and illuminating the low beam headlights using the light control switch.


Procedure1

a.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
Result:
Result Proceed to
Only B2439 for HL AutoLeveling is output A
Only B243A for HL AutoLeveling (Sub) is output B
None of the above conditions are met C



Malfunction Content System Relevant DTC
Headlight ECU sub-assembly LH HL AutoLeveling B2439 Headlight LH Circuit
Headlight ECU sub-assembly RH HL AutoLeveling (Sub) B243A Headlight RH Circuit

Post-procedure1

a.

None



A

12.CHECK HEADLIGHT UNIT ASSEMBLY LH

B

15.CHECK HEADLIGHT UNIT ASSEMBLY RH

C

12.CHECK HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.

Interchange the headlight unit assembly LH with RH and connect the connectors to them.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL



Procedure1

a.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

13.CHECK HEADLIGHT UNIT ASSEMBLY LH
13.CHECK HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.

10 seconds elapse after turning the ignition switch ON and illuminating the low beam headlights using the light control switch.


Procedure1

a.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Result:
Result Proceed to
B2439 is not output A
B2439 is output B



Post-procedure1

a.

None



A

14.CHECK HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

14.CHECK HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.
E459081C02
1.448,0.094 1.854,0.427 0.406,0.333 1.521,1.896 1.927,2.229 0.406,0.333 1.625,0.188 1.781,0.385 0.156,0.198 10 false B 1.677,1.99 1.833,2.188 0.156,0.198 10 false D 0.583,0.146 0.896,0.302 0.313,0.156 10 false *a 0.594,2 0.906,2.156 0.313,0.156 10 false *b
*a Component without harness connected
(Headlight ECU Sub-assembly LH)
*b Component without harness connected
(Headlight Unit LH)


Remove the headlight unit LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 - D-1 Always Below 1 Ω
B-5 - D-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

15.CHECK HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Interchange the headlight unit assembly RH with LH and connect the connectors to them.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL



Procedure1

a.

Clear the DTCs.

Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

16.CHECK HEADLIGHT UNIT ASSEMBLY RH
16.CHECK HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

10 seconds elapse after turning the ignition switch ON and illuminating the low beam headlights using the light control switch.


Procedure1

a.

Check for DTCs.

Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
Result:
Result Proceed to
B243A is not output A
B243A is output B



Post-procedure1

a.

None



A

17.CHECK HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

17.CHECK HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight unit RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

a.
E459081C02
1.448,0.094 1.854,0.427 0.406,0.333 1.521,1.896 1.927,2.229 0.406,0.333 1.625,0.188 1.781,0.385 0.156,0.198 10 false B 1.677,1.99 1.833,2.188 0.156,0.198 10 false D 0.583,0.146 0.896,0.302 0.313,0.156 10 false *a 0.594,2 0.906,2.156 0.313,0.156 10 false *b
*a Component without harness connected
(Headlight ECU Sub-assembly LH)
*b Component without harness connected
(Headlight Unit LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 - D-1 Always Below 1 Ω
B-5 - D-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH