Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448416 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog light.

WIRING DIAGRAM

E457465E01
0.438,1.427 2.063,1.969 1.625,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 6.333,1.677 6.792,1.875 0.458,0.198 10 false CPU 5.594,2.615 6.052,2.813 0.458,0.198 10 false IPD 5.708,2.063 6.167,2.26 0.458,0.198 10 false +B 2.635,2.49 2.792,2.688 0.156,0.198 10 false B 0.625,4.438 3.031,4.635 2.406,0.198 10 false : CXPI Communication Line 1.25,3.25 3.698,3.448 2.448,0.198 10 false J28 1.427,2.49 1.583,2.688 0.156,0.198 10 false E 2.896,2.49 3.052,2.688 0.156,0.198 10 false 1 1.188,2.49 1.344,2.688 0.156,0.198 10 false 2 1.698,2.906 4.146,3.104 2.448,0.198 10 false Rear Fog Light 5.052,2.49 5.208,2.688 0.156,0.198 10 false L 4.667,2.49 5.125,2.688 0.458,0.198 10 false 18 4.854,3.396 5.469,3.594 0.615,0.198 10 false G102 4.854,3.542 7.083,4.156 2.229,0.615 10 false No. 2 Semiconductor Power Integration ECU 1.271,3.427 3.719,3.625 2.448,0.198 10 false Rear Light Lens and Body

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

First, confirm that there is no malfunction in the power integration system. Refer to the How to Proceed with Troubleshooting procedure.

Click herePower Source / Network>POWER DISTRIBUTION>POWER INTEGRATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Fog Light Input Signal Rear fog light switch input signal OFF or ON OFF: Rear fog light switch off
ON: Rear fog light switch on
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Rear Fog Light Input Signal
50003 412 71
OK:

Display changes according to the rear fog light switch operation.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

2.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Fog Light Output Signal Rear fog light output condition OFF or ON OFF: Rear fog light not illuminated
ON: Rear fog light illuminated
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Rear Fog Light Output Signal
50003 412 77
OK:

Display changes according to the rear fog light switch operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

3.READ VALUE USING GTS
a.

Turn the rear fog light switch on.


b.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Status of Rear Fog Light Fuse Rear fog light fuse Connect or Disconnect Connect: Fuse not shut off
Disconnect: Fuse shut off
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Status of Rear Fog Light Fuse
50003 412 91
OK:

The Data List value displays "Connect".



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.CHECK REAR FOG LIGHT SOCKET AND WIRE
4.CHECK REAR FOG LIGHT SOCKET AND WIRE
a.

Disconnect the J28 rear fog light socket and wire connector.


b.

Turn the rear fog light switch off.


c.

Turn the rear fog light switch on.


d.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Status of Rear Fog Light Fuse Rear fog light fuse Connect or Disconnect Connect: Fuse not shut off
Disconnect: Fuse shut off
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Status of Rear Fog Light Fuse
50003 412 91
OK:

The Data List value displays "Connect".



Result:
Proceed to
OK
NG



OK

REPLACE REAR FOG LIGHT SOCKET AND WIRE

NG

5.CHECK HARNESS AND CONNECTOR (REAR LIGHT LENS AND BODY - NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU)
5.CHECK HARNESS AND CONNECTOR (REAR LIGHT LENS AND BODY - NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU)
a.

Disconnect the J28 rear light lens and body LH connector.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(J28,G102)Location & Routing

Click Connector(J28)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>Rear Fog Light

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

J28-1(B) or G102-18(L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR