Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448416 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Back-up Light Circuit  


DESCRIPTION

The illumination of the back-up lights is controlled by release signals sent to the No. 2 semiconductor power integration ECU from the shift control ECU.

WIRING DIAGRAM

E384726E06
0.531,1.719 3.135,1.917 2.604,0.198 10 false D92 0.531,1.875 3.135,2.073 2.604,0.198 10 false Shift Control ECU 1.26,1.063 3.865,1.26 2.604,0.198 10 false BL 1.583,0.969 4.188,1.167 2.604,0.198 10 false 15 4.74,0.958 5.375,1.271 0.635,0.313 10 false 11 5.031,0.958 5.667,1.271 0.635,0.313 10 false +S 6.302,1.958 6.938,2.271 0.635,0.313 10 false CPU 5.667,2.292 6.302,2.604 0.635,0.313 10 false +B 5.542,2.896 6.177,3.208 0.635,0.313 10 false IPD 5.031,2.792 5.667,3.104 0.635,0.313 10 false L 4.99,3.677 6.76,4.073 1.771,0.396 10 false G102 5,3.854 6.771,4.25 1.771,0.396 10 false No. 3 Semiconductor Power Integration ECU 4.813,2.792 5.448,3.104 0.635,0.313 10 false 4 3.615,2.771 4.25,3.083 0.635,0.313 10 false 2 3.615,4.552 4.25,4.865 0.635,0.313 10 false 2 0.573,4.552 1.208,4.865 0.635,0.313 10 false 4 0.563,2.771 1.198,3.083 0.635,0.313 10 false 4 2.406,6.604 3.042,6.917 0.635,0.313 10 false REV 1.781,7.271 3.635,7.625 1.854,0.354 10 false G13 1.781,7.427 3.635,7.781 1.854,0.354 10 false Parking Assist ECU 2.833,6.51 3.469,6.823 0.635,0.313 10 false 14 3.385,4.531 4.021,4.844 0.635,0.313 10 false B 3.396,2.792 4.031,3.104 0.635,0.313 10 false B 0.792,2.802 1.427,3.115 0.635,0.313 10 false E 0.792,4.552 1.427,4.865 0.635,0.313 10 false E 1.75,3.104 3.302,3.438 1.552,0.333 10 false Back-up Light 1.719,4.844 3.271,5.177 1.552,0.333 10 false Back-up Light 1.25,3.813 3.438,4.167 2.188,0.354 10 false K6 1.25,3.99 3.438,4.344 2.188,0.354 10 false Rear Light Assembly LH 1.25,5.573 3.438,5.927 2.188,0.354 10 false K10 1.25,5.74 3.438,6.094 2.188,0.354 10 false Rear Light Assembly RH 1.115,5.167 3.302,5.521 2.188,0.354 10 false Rear Light Socket and Wire RH 1.219,3.417 3.406,3.771 2.188,0.354 10 false Rear Light Socket and Wire LH

CAUTION / NOTICE / HINT

NOTICE:
·

First, confirm that there is no malfunction in the power integration system. Refer to the How to Proceed with Troubleshooting procedure.

Click herePower Source / Network>POWER DISTRIBUTION>POWER INTEGRATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.READ VALUE USING GTS
a.

Turn the ignition switch to ON.


b.

Changes the shift lever R position.


c.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Status of Back-up Light Fuse Back-up light fuse Connect or Disconnect Connect: Fuse not shut off
Disconnect: Fuse shut off
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Status of Back-up Light Fuse
50003 412 93
OK:

The Data List value displays "Connect".



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

7.CHECK REAR LIGHT ASSEMBLY LH
2.READ VALUE USING GTS
a.

Turn the ignition switch to ON.


b.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back-up Light Input Signal Back-up light input condition OFF or ON OFF: Shift lever in any position other than R
ON: Shift lever in R
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Back-up Light Input Signal
50003 412 73
OK:

Display changes according to shift lever operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

5.CHECK SHIFT CONTROL ECU
3.READ VALUE USING GTS
a.

Turn the ignition switch to ON.


b.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back-up Light Output Signal Back-up light output condition OFF or ON OFF: Back-up light not illuminated
ON: Back-up light illuminated
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Back-up Light Output Signal
50003 412 79
OK:

Display changes according to shift lever operation.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR LIGHT LENS AND BODY LH - NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU)

NG

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

4.CHECK HARNESS AND CONNECTOR (REAR LIGHT LENS AND BODY LH - NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU)
a.

Disconnect the K6 rear light lens and body LH connector.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K6,G102)Location & Routing

Click Connector(K6)Body>No. 1 Back Door Wire>Rear Light Assembly LH

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

K6-2 (B) - G102-4 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK SHIFT CONTROL ECU
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G102)Location & Routing

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

G102-11 (+S) - Body ground Ignition switch ON ((READY), shift lever R position 7.25 to 14.65 V
Ignition switch ON ((READY), shift lever except R position Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

NG

6.CHECK HARNESS AND CONNECTOR (NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU - SHIFT CONTROL ECU)
6.CHECK HARNESS AND CONNECTOR (NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU - SHIFT CONTROL ECU)
a.

Disconnect the D92 shift control ECU connector.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G102,D92)Location & Routing

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

G102-11 (+S) - D92-15 (BL) Always Below 1 Ω
G102-11 (+S) or D92-15 (BL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK REAR LIGHT ASSEMBLY LH
a.

Disconnect the K6 rear light assembly LH connector.


b.

Turn the ignition switch to ON.


c.

Changes the shift lever except R position.


d.

Changes the shift lever R position.


e.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Status of Back-up Light Fuse Back-up light fuse Connect or Disconnect Connect: Fuse not shut off
Disconnect: Fuse shut off
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Status of Back-up Light Fuse
50003 412 93
OK:

The Data List value displays "Connect".



Result:
Proceed to
OK
NG



OK

8.CHECK REAR LIGHT SOCKET AND WIRE LH

NG

9.CHECK REAR LIGHT ASSEMBLY RH
8.CHECK REAR LIGHT SOCKET AND WIRE LH
a.

Disconnect the rear light socket and wire LH connector.


b.

Reconnect the K6 rear light assembly LH connector.


c.

Turn the ignition switch to ON.


d.

Changes the shift lever except R position.


e.

Changes the shift lever R position.


f.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Status of Back-up Light Fuse Back-up light fuse Connect or Disconnect Connect: Fuse not shut off
Disconnect: Fuse shut off
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Status of Back-up Light Fuse
50003 412 93
OK:

The Data List value displays "Connect".



Result:
Proceed to
OK
NG



OK

REPLACE REAR LIGHT SOCKET AND WIRE LH

NG

REPLACE REAR LIGHT ASSEMBLY LH

9.CHECK REAR LIGHT ASSEMBLY RH
a.

Disconnect the K10 rear light assembly RH connector.


b.

Turn the ignition switch to ON.


c.

Changes the shift lever except R position.


d.

Changes the shift lever R position.


e.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Status of Back-up Light Fuse Back-up light fuse Connect or Disconnect Connect: Fuse not shut off
Disconnect: Fuse shut off
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Status of Back-up Light Fuse
50003 412 93
OK:

The Data List value displays "Connect".



Result:
Proceed to
OK
NG



OK

10.CHECK REAR LIGHT SOCKET AND WIRE RH

NG

11.CHECK PARKING ASSIST ECU
10.CHECK REAR LIGHT SOCKET AND WIRE RH
a.

Disconnect the rear light socket and wire RH connector.


b.

Reconnect the K10 rear light assembly RH connector.


c.

Turn the ignition switch to ON.


d.

Changes the shift lever except R position.


e.

Changes the shift lever R position.


f.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Status of Back-up Light Fuse Back-up light fuse Connect or Disconnect Connect: Fuse not shut off
Disconnect: Fuse shut off
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Status of Back-up Light Fuse
50003 412 93
OK:

The Data List value displays "Connect".



Result:
Proceed to
OK
NG



OK

REPLACE REAR LIGHT SOCKET AND WIRE RH

NG

REPLACE REAR LIGHT ASSEMBLY RH

11.CHECK PARKING ASSIST ECU
a.

Disconnect the G13 parking assist ECU connector.


b.

Turn the ignition switch to ON.


c.

Changes the shift lever except R position.


d.

Changes the shift lever R position.


e.

Using the GTS, read the Data List.

Body Electrical > Power Integration No.3 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Status of Back-up Light Fuse Back-up light fuse Connect or Disconnect Connect: Fuse not shut off
Disconnect: Fuse shut off
-
Body Electrical > Power Integration No.3 > Data List
Tester Display
Status of Back-up Light Fuse
50003 412 93
OK:

The Data List value displays "Connect".



Result:
Proceed to
OK
NG



OK

NG

12.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT CIRCUIT)
12.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT CIRCUIT)
a.

Disconnect the K6 rear light lens and body LH connector.


b.

Disconnect the K10 rear light lens and body RH connector.


c.

Disconnect the G13 parking assist ECU connector.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.


e.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K6,G102)Location & Routing

Click Connector(K6)Body>No. 1 Back Door Wire>Rear Light Assembly LH

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

K6-2 (B) or G102-4 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR