Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (READY)  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift state is park (P) and the brake pedal is depressed, the hybrid control system can be started by pressing the ignition switch. If the steering is unlocked, the hybrid control system can also be started by pressing the power switch with the shift state park (P) and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to ON (READY)
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Shift P Signal Pulse

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Engine/System Start Request

·

S Code Check

·

L Code Check



WIRING DIAGRAM

for LHD:
C450879E09
0.25,0.302 1.146,1.094 0.896,0.792 10 false from Auxiliary Battery 1.667,0.552 2.083,0.719 0.417,0.167 10 false STOP 2.24,0.292 2.49,0.458 0.25,0.167 10 false 1 2.417,0.375 2.594,0.573 0.177,0.198 10 false B 2.427,0.792 2.833,0.979 0.406,0.188 10 false GND 2.313,1.188 2.625,1.354 0.313,0.167 10 false A3 2.281,1.354 4.281,1.573 2,0.219 10 false Stop Light Switch Assembly 2.865,0.615 3.042,0.781 0.177,0.167 10 false IC 3.188,0.396 3.375,0.563 0.188,0.167 10 false L 3.375,0.396 3.583,0.594 0.208,0.198 10 false 2 4.969,0.292 5.229,0.458 0.26,0.167 10 false 25 4.938,0.479 5.25,0.677 0.313,0.198 10 false G37 5.323,0.396 5.823,0.604 0.5,0.208 10 false STP1 6.219,0.646 6.406,0.833 0.188,0.188 10 false IC 5.708,2.031 5.99,2.229 0.281,0.198 10 false +B 6.208,2.656 6.427,2.844 0.219,0.188 10 false IC 5.323,2.417 5.677,2.573 0.354,0.156 10 false ST2 4.958,2.323 5.198,2.49 0.24,0.167 10 false 27 4.99,4.073 6.76,4.656 1.771,0.583 10 false Certification ECU (Smart Key ECU Assembly) 5.313,5.083 5.719,5.271 0.406,0.188 10 false ST2 4.99,4.99 5.219,5.188 0.229,0.198 10 false 19 4.969,5.188 5.438,5.438 0.469,0.25 10 false A8 5.021,5.5 5.302,5.688 0.281,0.188 10 false 7 4.948,5.708 5.281,5.865 0.333,0.156 10 false A17 5.313,5.708 5.719,5.896 0.406,0.188 10 false STP 5.219,6.135 7.094,6.458 1.875,0.323 10 false EV Control ECU 3.396,1.75 3.802,1.938 0.406,0.188 10 false D92 2.396,2.771 4.083,3.063 1.688,0.292 10 false Shift Control ECU 3.021,2.354 3.375,2.542 0.354,0.188 10 false STP 3.438,2.135 3.844,2.323 0.406,0.188 10 false 18 1.927,4.833 2.333,5.021 0.406,0.188 10 false A6 1.615,3.927 4.073,4.344 2.458,0.417 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.385,3.406 3.667,3.594 0.281,0.188 10 false 37 3.01,3.5 3.417,3.688 0.406,0.188 10 false STP 2,5.958 2.406,6.146 0.406,0.188 10 false G102 2.01,6.135 3.76,6.615 1.75,0.479 10 false No. 3 Semiconductor Power Integration ECU 3.375,5.635 3.625,5.813 0.25,0.177 10 false 10 2.26,0.688 2.51,0.854 0.25,0.167 10 false 3 4.938,1.74 5.25,1.927 0.313,0.188 10 false D86 4.979,1.542 5.219,1.708 0.24,0.167 10 false 22 3.396,2.323 3.802,2.51 0.406,0.188 10 false D93 3.448,1.542 3.854,1.729 0.406,0.188 10 false 13 2.865,1.667 3.417,1.896 0.552,0.229 10 false PPOS 5.333,1.635 5.688,1.792 0.354,0.156 10 false P 3.01,5.74 3.365,5.927 0.354,0.188 10 false STP 4.948,2.51 5.26,2.698 0.313,0.188 10 false D86 6.229,1.75 6.448,1.938 0.219,0.188 10 false IC 3,4.583 3.406,4.771 0.406,0.188 10 false STP 3.385,4.469 3.667,4.656 0.281,0.188 10 false 11 1.927,5 3.844,5.396 1.917,0.396 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 1.615,3.75 2.021,3.938 0.406,0.188 10 false A5

for RHD:
C450879E07
0.25,0.302 1.146,1.094 0.896,0.792 10 false from Auxiliary Battery 1.667,0.552 2.083,0.719 0.417,0.167 10 false STOP 2.24,0.292 2.49,0.458 0.25,0.167 10 false 1 2.417,0.375 2.594,0.573 0.177,0.198 10 false B 2.427,0.792 2.833,0.979 0.406,0.188 10 false GND 2.313,1.188 2.625,1.354 0.313,0.167 10 false A3 2.281,1.354 4.281,1.573 2,0.219 10 false Stop Light Switch Assembly 2.865,0.615 3.042,0.781 0.177,0.167 10 false IC 3.188,0.396 3.375,0.563 0.188,0.167 10 false L 3.375,0.396 3.583,0.594 0.208,0.198 10 false 2 4.969,0.292 5.229,0.458 0.26,0.167 10 false 25 4.938,0.479 5.25,0.677 0.313,0.198 10 false G37 5.323,0.396 5.823,0.604 0.5,0.208 10 false STP1 6.219,0.646 6.406,0.833 0.188,0.188 10 false IC 5.708,2.031 5.99,2.229 0.281,0.198 10 false +B 6.208,2.656 6.427,2.844 0.219,0.188 10 false IC 5.323,2.417 5.677,2.573 0.354,0.156 10 false ST2 4.958,2.323 5.198,2.49 0.24,0.167 10 false 27 4.99,4.073 6.76,4.656 1.771,0.583 10 false Certification ECU (Smart Key ECU Assembly) 5.313,5.083 5.719,5.271 0.406,0.188 10 false ST2 5.031,4.99 5.26,5.188 0.229,0.198 10 false 19 4.938,5.177 5.406,5.427 0.469,0.25 10 false D15 5.042,5.5 5.323,5.688 0.281,0.188 10 false 7 4.948,5.708 5.281,5.865 0.333,0.156 10 false A17 5.313,5.708 5.719,5.896 0.406,0.188 10 false STP 5.219,6.135 7.094,6.458 1.875,0.323 10 false EV Control ECU 3.396,1.75 3.802,1.938 0.406,0.188 10 false D92 2.396,2.771 4.083,3.063 1.688,0.292 10 false Shift Control ECU 3.021,2.354 3.375,2.542 0.354,0.188 10 false STP 3.438,2.135 3.844,2.323 0.406,0.188 10 false 18 1.927,4.833 2.333,5.021 0.406,0.188 10 false A6 1.615,3.927 4.073,4.344 2.458,0.417 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.385,3.406 3.667,3.594 0.281,0.188 10 false 37 3.01,3.5 3.417,3.688 0.406,0.188 10 false STP 2,5.958 2.406,6.146 0.406,0.188 10 false G102 2.01,6.135 3.76,6.615 1.75,0.479 10 false No. 3 Semiconductor Power Integration ECU 3.375,5.635 3.625,5.813 0.25,0.177 10 false 10 2.26,0.688 2.51,0.854 0.25,0.167 10 false 3 4.938,1.74 5.25,1.927 0.313,0.188 10 false D86 4.979,1.542 5.219,1.708 0.24,0.167 10 false 22 3.396,2.323 3.802,2.51 0.406,0.188 10 false D93 3.448,1.542 3.854,1.729 0.406,0.188 10 false 13 2.865,1.667 3.417,1.896 0.552,0.229 10 false PPOS 5.333,1.635 5.688,1.792 0.354,0.156 10 false P 3.01,5.74 3.365,5.927 0.354,0.188 10 false STP 4.948,2.51 5.26,2.698 0.313,0.188 10 false D86 6.229,1.75 6.448,1.938 0.219,0.188 10 false IC 3,4.583 3.406,4.771 0.406,0.188 10 false STP 3.385,4.469 3.667,4.656 0.281,0.188 10 false 11 1.927,5 3.844,5.396 1.917,0.396 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 1.615,3.75 2.021,3.938 0.406,0.188 10 false A5

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to the Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

NOTICE:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK POWER SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Push the P position switch(shift position indication).


c.

With the brake pedal released, check that pressing the power switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) or on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG and ACC))

C

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (ACC))

D

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG))

2.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (SHIFT POSITION P)

NG

12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
3.READ VALUE USING GTS (SHIFT POSITION P)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Pulse P position signal status Normal2, Normal3, Normal4, Normal5 or Unknown Normal2: Signal normal and park (P) selected
Normal3: Signal normal and shift state other than (P)
Normal4: Signal normal and park (N) selected
Normal5: Signal normal and park other than (P) or (N) selected
Unknown: -
Use this item to determine if the P position signal is malfunctioning.
Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal Pulse
50003 223 42
OK:

The GTS display changes correctly in response to the shift state.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

9.CHECK SHIFT CONTROL ECU (OUTPUT TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Hybrid control system start request signal status OFF or ON OFF: The power switch is not pressed
ON: With the shift state park (P) and the brake pedal depressed, the power switch is pressed and held
·

When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the power switch.


OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EV CONTROL ECU)

NG

7.CHECK STEERING LOCK
5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EV CONTROL ECU)
a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D15 EV control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86,D15)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D86-27 (ST2) - D15-19 (ST2) Always Below 1 Ω
D86-27 (ST2) or D15-19 (ST2) - Other terminals and body ground Always 10 kΩ or higher



d.

Connect the D86 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B498244C60
1.604,0.115 1.969,0.354 0.365,0.24 1.021,1.99 1.219,1.99 1.219,1.99 1.219,1.073 false 1.677,0.156 2.021,0.354 0.344,0.198 10 false D86 0.698,1.938 1.292,2.135 0.594,0.198 10 false ST2 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-27 (ST2) - Body ground With the brake pedal depressed, the power switch is pressed and held → After approximately 3 sec. has elapsed, the power switch is released 8.5 V or higher → 1 V or less



Result:
Proceed to
OK
NG



OK

GO TO HYBRID CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK STEERING LOCK
a.

Check that the steering unlocks when the ignition switch is turned to ACC.

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

8.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Unable to Unlock Steering Wheel (Hybrid Control System cannot Start))

8.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Push the P position switch(shift position indication).


c.

Press the power switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Immobiliser System does not Operate Properly)

9.CHECK SHIFT CONTROL ECU (OUTPUT TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Using an oscilloscope, check the waveform.

C376309C07
4.563,0.354 4.948,0.563 0.385,0.208 4.25,2.24 4.729,1.229 true 5.438,2.229 5.156,1.24 true 0.396,0.229 0.708,0.427 0.313,0.198 10 false *a 0.99,2.906 1.302,3.104 0.313,0.198 10 false *b 5.458,2.25 5.771,2.448 0.313,0.198 10 false E 4.167,2.26 4.479,2.458 0.313,0.198 10 false P 4.635,0.375 4.948,0.573 0.313,0.198 10 false D86 0.771,3.885 1.083,4.083 0.313,0.198 10 false GND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-22 (P) - D86-18 (E) Procedure:
1.

Ignition switch ON

2.

Shift state park (P)


10 V/DIV., 10 ms./DIV. Pulse generation
(See waveform)


HINT:

The waveform will vary depending on the shift state.


OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT CONTROL ECU)
10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT CONTROL ECU)
a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D92 shift control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86,D92)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D86-22 (P) - D92-13 (PPOS) Always Below 1 Ω
D86-22 (P) or D92-13 (PPOS) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK SHIFT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK SHIFT CONTROL ECU
a.
B498244C64
1.604,0.115 1.969,0.354 0.365,0.24 2.083,1.917 1.917,1.917 1.917,1.917 1.833,1.094 false 1.677,0.167 2.021,0.365 0.344,0.198 10 false D86 2.125,1.865 2.719,2.063 0.594,0.198 10 false P 0.156,0.146 0.469,0.302 0.313,0.156 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Connect the certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-22 (P) - Body ground Procedure:
1.

Ignition switch ON

2.

Shift state park (P)


11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
a.

Disconnect the A3 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-1 (B) - Body ground Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A17 EV control ECU connector.


c.

Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the D93 shift control ECU connector.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.


g.

Disconnect the G102 semiconductor power integration ECU connector.


h.

Connect the cable to the negative (-) auxiliary battery terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,A3)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

G37-25 (STP1) - A3-2 (L) Always Below 1 Ω
G37-25 (STP1) or A3-2 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY