The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front axle hub bolt removal/installation are shown below.
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.
When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Air conditioning system | After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. | - |
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1.DISABLE BRAKE CONTROL
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
2.REMOVE FRONT WHEEL
47750
3.DISCONNECT DISC BRAKE CYLINDER ASSEMBLY LH
43512
4.REMOVE FRONT DISC
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>REMOVAL
43502D
5.REMOVE FRONT AXLE HUB BOLT LH
| *a | Service Nut |
| *b | Hold |
| *c | Turn |
Temporarily install 2 service nuts to the front axle hub bolts as shown in the illustration.
Thread diameter: 14.0 mm (0.551 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Install the service nuts to prevent damage to the front axle hub bolts.
Using SST and a screwdriver or an equivalent tool to hold the front axle hub, remove the front axle hub bolt.
Do not damage the threads of the front axle hub bolts.
43502D
6.INSTALL FRONT AXLE HUB BOLT LH
Temporarily install a new front axle hub bolt to the front axle hub.
| *a | Service Nut |
| *b | Washer |
| *c | Hold |
| *d | Turn |
Install a washer and service nut to a new front axle hub bolt as shown in the illustration.
Thread diameter: 14.0 mm (0.551 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Recommended washer thickness is 5 mm (0.197 in.) or more.
Using a screwdriver or an equivalent tool to hold the front axle hub, install the front axle hub bolt by tightening the service nut.
Install the service nuts to prevent damage to the front axle hub bolts.
Do not damage the threads of the front axle hub bolts.
Remove the 3 service nuts and washer from the 3 front axle hub bolts.
43512
7.INSTALL FRONT DISC
47750
8.CONNECT DISC BRAKE CYLINDER ASSEMBLY LH
9.INSTALL FRONT WHEEL
10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
11. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART