Home › Brake › BRAKE (REAR) › REAR BRAKE
RM37H0E _54 Brake _097303 BRAKE (REAR) _0455483 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C450043N05
6.438,0.188 6.854,0.188 false 6.458,0.604 6.813,0.604 false 4.667,1.24 4.792,1.01 4.792,1.01 4.958,1.01 true 6.479,1.052 6.833,1.052 false 6.229,0.042 6.479,0.344 0.25,0.302 18 false 1 5.052,0.875 5.385,1.229 0.333,0.354 18 false 3 6.24,0.469 6.563,0.771 0.323,0.302 18 false 2 6.229,0.906 6.521,1.198 0.292,0.292 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - - - (Click here)
3 REAR WHEEL - - - -
4 DRAIN BRAKE FLUID - - (Click here) -

C451998N02
3.479,4.167 5.25,5.417 1.771,1.25 0.167,2.667 1.917,4.333 1.75,1.667 2,3.656 3.365,5.406 1.365,1.75 1.323,1.083 4.073,2.479 2.75,1.396 2.406,4.917 2.406,4.135 false 2.25,4.917 2.854,4.917 2.854,4.917 2.854,4.5 true 4.125,4.51 3.875,4.51 false 4.833,5 4.635,5 true 1.135,3.646 1.385,3.646 true 0.417,3.135 0.667,3.135 true 3.083,2.25 3.083,1.667 3.083,1.667 2.844,1.667 true 2.583,2.083 3.083,2.083 true 1.615,1.542 1.865,1.542 true 3.396,1.563 3.5,1.333 3.5,1.333 3.583,1.333 true 3.5,3 2.333,3 2.333,3 2.333,3.063 true 3.042,3.427 3.042,3 true 4.5,3.75 4.333,3.75 4.333,3.75 4.333,4.167 false 1.146,4.333 1.146,4.635 1.146,4.635 0.979,4.635 false 1.833,4.917 2,4.917 true 1.146,1.385 1.313,1.385 true 4.208,4.438 4.521,4.635 0.313,0.198 10 false *1 0.927,3.594 1.188,3.792 0.26,0.198 10 false *1 0.219,3.063 0.49,3.302 0.271,0.24 10 false *2 4.885,4.927 5.104,5.125 0.219,0.198 10 false *2 1.406,1.469 1.698,1.75 0.292,0.281 10 false *3 3,2.302 3.292,2.583 0.292,0.281 10 false *4 3.667,1.24 3.958,1.521 0.292,0.281 10 false *5 3.594,2.927 3.885,3.208 0.292,0.281 10 false *6 1.594,4.76 1.896,5.073 0.302,0.313 18 false 6 4.563,3.604 4.875,3.938 0.313,0.333 18 false 7 0.76,4.51 1.073,4.844 0.313,0.333 18 false 7 2.042,4.844 2.333,5.125 0.292,0.281 10 false *7 0.917,1.24 1.229,1.573 0.313,0.333 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

5 REAR DISC BRAKE FITTING KIT 04948 - - -
6 REAR DISC BRAKE PAD KIT 04466 (Click here) - -
7 REAR DISC BRAKE ANTI-SQUEAL SHIM 04946 - - -

*1 NO. 1 ANTI-SQUEAL SHIM *2 NO. 2 ANTI-SQUEAL SHIM
*3 PIN HOLD CLIP *4 HOLE PIN
*5 NO. 1 ANTI-RATTLE SPRING *6 INNER ANTI-RATTLE SPRING
*7 REAR DISC BRAKE PAD - -

C450052N02
5.521,2.365 5.667,1.542 5.667,1.542 5.917,1.542 true 6.781,4.073 6.698,4.073 6.698,4.073 6.615,4.323 true 2.5,5 2.75,5 2.75,5 3,4.448 true 1.219,3.813 1.469,3.813 1.469,3.813 1.635,3.229 true 0.75,2.365 1.021,2.365 true 0.563,2.99 0.833,2.99 true 1,3.688 1.281,4.042 0.281,0.354 18 false 8 2.292,4.875 2.615,5.188 0.323,0.313 18 false 9 6.823,3.927 7.135,4.292 0.313,0.365 18 false 10 6.26,1.396 6.708,1.833 0.448,0.438 18 false 11 0.375,2.292 0.844,2.542 0.469,0.25 10 false ● *1 0.167,2.927 0.594,3.219 0.427,0.292 10 false ● *2 2.271,0.438 2.552,0.625 0.281,0.188 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

8 REAR FLEXIBLE HOSE LH 47319F - - -
9 REAR DISC BRAKE CYLINDER ASSEMBLY LH 47850 - - -
10 PARKING BRAKE SHOE ADJUSTING HOLE PLUG 42491 - - -
11 REAR DISC LH 42432 (Click here)

*1 UNION BOLT *2 GASKET
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear brake removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Rear disc (Including removal and installation)

·

Parking brake shoe (Including removal and installation)


Parking brake bedding Electric parking brake system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH and LH sides, except where indicated.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

Click here(Click here)
NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISABLE BRAKE CONTROL

a.
C451326N01
0.417,0.031 0.698,0.385 0.281,0.354 18 false i

i.

Wait at least 2 minutes after turning the power switch off.

NOTICE:

When the brake pedal is depressed or the door courtesy switch is turned on even if the ignition switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



ii.

Disconnect the connector from the brake master cylinder reservoir assembly


iii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL


iv.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


v.

Check that the brake pedal cannot be further depressed.



Hide 3.REMOVE REAR WHEEL

Hide 4.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 04948 5.REMOVE REAR DISC BRAKE FITTING KIT

Hide 04466 6.REMOVE REAR DISC BRAKE PAD KIT

Z101186

Click here(Click here)

Hide 04946 7.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM

Hide 47319F 8.DISCONNECT REAR FLEXIBLE HOSE LH

a.
C450055


Hide 47850 9.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.
C450056


Hide 42491 10.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.
C451327


Hide 42432 11.REMOVE REAR DISC LH

a.
C450057C02
2.188,0.875 2.521,0.875 2.521,0.875 2.521,0.948 true 2.208,0.948 2.854,0.948 true 3.99,0.042 4.302,0.344 0.313,0.302 18 false ii 0.438,0.052 0.708,0.333 0.271,0.281 18 false i 2.927,0.875 3.24,1.073 0.313,0.198 10 false *a
*a Matchmark - -
V113147

Contract - -


i.

Put matchmarks on the rear disc LH and the rear axle hub and bearing assembly LH.

HINT:

Not required when replacing the rear disc LH.



ii.

Release the parking brake and remove the rear disc LH.

HINT:

If the rear disc LH cannot be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.