The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced when performing the front axle hub inspection are shown below.
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.
When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Air conditioning system | After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. | - |
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISABLE BRAKE CONTROL
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
3.REMOVE FRONT WHEEL
47750
4.DISCONNECT DISC BRAKE CYLINDER ASSEMBLY LH
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL
43512
5.REMOVE FRONT DISC
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>REMOVAL
6.INSPECT FRONT AXLE HUB BEARING LOOSENESS
Using a dial indicator, check for looseness near the center of the front axle hub sub-assembly.
| Specified Condition |
|---|
| 0.05 mm
0.00197 in. |
Ensure that the dial indicator is set perpendicular to the measurement surface.
Keep the magnet of the dial indicator away from the front speed sensor.
If the looseness exceeds the maximum, replace the front axle hub sub-assembly.
7.INSPECT FRONT AXLE HUB RUNOUT
Using a dial indicator, check for runout on the surface of the front axle hub sub-assembly outside the front axle hub bolts.
| Specified Condition |
|---|
| 0.05 mm
0.00197 in. |
Ensure that the dial indicator is set perpendicular to the measurement surface.
Make sure to set the tip of the dial indicator towards the outside of the front axle hub bolts.
Keep the magnet of the dial indicator away from the front speed sensor.
If the runout exceeds the maximum, replace the front axle hub sub-assembly.
43512
8.INSTALL FRONT DISC
47750
9.CONNECT DISC BRAKE CYLINDER ASSEMBLY LH
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSTALLATION
10.INSTALL FRONT WHEEL
11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
12. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART