Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD DEICER SYSTEM
RM37H0E _59 Vehicle Exterior _095305 WINDOW / GLASS _0453653 WINDSHIELD DEICER SYSTEM J

WINDOW / GLASS  WINDSHIELD DEICER SYSTEM  Windshield Deicer does not Operate  


DESCRIPTION

When the front wiper deicer switch is operated, an activation request signal is sent to the air conditioning control assembly through the direct line. The air conditioning control assembly sends an operation request signal to the air conditioning amplifier assembly via LIN communication, and when the air conditioning amplifier assembly receives the operation request signal, the system turns on the front wiper deicer relay (DEICER) and operates the windshield deicer system.

WIRING DIAGRAM

E458437E01
1.177,2.188 2.906,2.427 1.729,0.24 10 false Front Wiper Deicer Switch 1.208,2.021 1.823,2.219 0.615,0.198 10 false D108 0.938,1.021 1.25,1.219 0.313,0.198 10 false IG 0.708,1.021 0.865,1.219 0.156,0.198 10 false 5 0.917,0.469 1.76,0.698 0.844,0.229 10 false IG1 D NO.3 2.479,0.24 4.177,0.479 1.698,0.24 10 false from IG1 D NO.1 Relay 2.573,4.031 3.177,4.25 0.604,0.219 10 false DEICER 3.302,4.344 4.875,4.74 1.573,0.396 10 false Front Wiper Deicer Relay (DEICER) 5.563,4.156 7.115,4.521 1.552,0.365 10 false Air Conditioning Amplifier Assembly 1.927,5.927 2.542,6.125 0.615,0.198 10 false A45 1.927,6.115 4.646,6.354 2.719,0.24 10 false Windshield Glass (Windshield Deicer Wire) 3.906,5.344 4.063,5.542 0.156,0.198 10 false B 2.438,5.333 2.594,5.531 0.156,0.198 10 false E 2.74,1.01 3.083,1.229 0.344,0.219 10 false IND- 2.896,1.458 3.052,1.656 0.156,0.198 10 false E 3.146,1.01 3.302,1.208 0.156,0.198 10 false 4 3.146,1.469 3.302,1.667 0.156,0.198 10 false 2 5.99,1.313 6.604,1.51 0.615,0.198 10 false LIN1 3.958,1.115 4.573,1.313 0.615,0.198 10 false IND 5.99,3.271 6.604,3.469 0.615,0.198 10 false FDEF 4.583,3.156 4.74,3.354 0.156,0.198 10 false 1 4.573,3.698 4.729,3.896 0.156,0.198 10 false 5 3.51,3.167 3.667,3.365 0.156,0.198 10 false 2 3.51,3.708 3.667,3.906 0.156,0.198 10 false 3 4.135,5.344 4.292,5.542 0.156,0.198 10 false 1 2.24,5.333 2.396,5.531 0.156,0.198 10 false 2 0.292,3.781 1.76,4.021 1.469,0.24 10 false from Auxiliary Battery 5.563,3.979 6.021,4.177 0.458,0.198 10 false D81 5.677,3.156 5.99,3.354 0.313,0.198 10 false 22 3.969,1.563 4.583,1.76 0.615,0.198 10 false DFAC 3.75,1 3.99,1.198 0.24,0.198 10 false 1 3.75,1.458 3.906,1.656 0.156,0.198 10 false 6 4.813,1.313 5.427,1.51 0.615,0.198 10 false LIN1 3.792,2.031 4.25,2.229 0.458,0.198 10 false D90 3.802,2.208 5.271,2.594 1.469,0.385 10 false Air Conditioning Control Assembly 0.51,6.469 2.167,6.698 1.656,0.229 10 false : LIN Communication Line 5.229,1.167 5.438,1.385 0.208,0.219 10 false 3 5.76,1.167 5.969,1.385 0.208,0.219 10 false 7 0.708,3.25 2.031,3.479 1.323,0.229 10 false from IG1 Relay 2.406,3.469 3.354,3.677 0.948,0.208 10 false R/B-IG1 NO.2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses and relay for circuits related to this system before performing the following procedure.

·

If the windshield deicer system is operated when the auxiliary battery voltage is low, due to the electrical load limit control that gives voltage supply priority to the power steering system, the windshield deicer system may not operate. In this case, check the vehicle control history of the power steering system and check that "Battery Voltage Drop: X208F" is not stored before proceeding with troubleshooting.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>VEHICLE CONTROL HISTORY



PROCEDURE

1.CHECK AIR CONDITIONING SYSTEM
a.

Check air conditioning system.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:

Both the windshield deicer system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.


OK:

The air conditioning system operates normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range
Deicer Relay (Front) Windshield glass (windshield deicer) OFF or ON
Body Electrical > Air Conditioner > Active Test
Tester Display
Deicer Relay (Front)
50004 121 38
OK:

The windshield deicer system operates normally.



Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT WIPER DEICER SWITCH

NG

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [WINDSHIELD DEICER WIRE] - BATTERY)
3.INSPECT FRONT WIPER DEICER SWITCH

OK

4.CHECK WIRE HARNESS AND CONNECTOR (FRONT WIPER DEICER SWITCH - BATTERY)

NG

REPLACE FRONT WIPER DEICER SWITCH

4.CHECK WIRE HARNESS AND CONNECTOR (FRONT WIPER DEICER SWITCH - BATTERY)
a.

Disconnect the D108 front wiper deicer switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D108)Location & Routing

Click Connector(D108)Instrument Panel>Instrument Panel Wire>Front Wiper Deicer Switch

D108-5 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS AND CONNECTOR (FRONT WIPER DEICER SWITCH - AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS AND CONNECTOR (FRONT WIPER DEICER SWITCH - AIR CONDITIONING CONTROL ASSEMBLY)
a.

Disconnect the D108 front wiper deicer switch connector.


b.

Disconnect the D90 air conditioning control assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D108,D90)Location & Routing

Click Connector(D108)Instrument Panel>Instrument Panel Wire>Front Wiper Deicer Switch

Click Connector(D90)Instrument Panel>Instrument Panel Wire>Air Conditioning Control Assembly

D108-2 (E) - D90-6 (DFAC) Always Below 1 Ω
D108-4 (IND-) - D90-1 (IND) Always Below 1 Ω
D108-2 (E) or D90-6 (DFAC) - Body ground Always 10 kΩ or higher
D108-4 (IND-) or D90-1 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK AIR CONDITIONING CONTROL ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK AIR CONDITIONING CONTROL ASSEMBLY
a.

b.

Check that the windshield deicer system operates normally.

OK:

The windshield deicer system operates normally.



Result:
Proceed to
OK
NG



OK

END (AIR CONDITIONING CONTROL ASSEMBLY IS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [WINDSHIELD DEICER WIRE] - BATTERY)
a.

Disconnect the A45 windshield glass (windshield deicer wire) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A45)Location & Routing

Click Connector(A45)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Wiper Deicer (Windshield Glass)

A45-1 (B) - Body ground Ignition switch ON, front wiper deicer switch off Below 1 V
Ignition switch ON, front wiper deicer switch on 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [WINDSHIELD DEICER WIRE] - BODY GROUND)

NG

9.INSPECT FRONT WIPER DEICER RELAY (DEICER)
8.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [WINDSHIELD DEICER WIRE] - BODY GROUND)
a.

Disconnect the A45 windshield glass (windshield deicer wire) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A45)Location & Routing

Click Connector(A45)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Wiper Deicer (Windshield Glass)

A45-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD GLASS (WINDSHIELD DEICER WIRE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT FRONT WIPER DEICER RELAY (DEICER)

OK

10.CHECK HARNESS AND CONNECTOR (FRONT WIPER DEICER RELAY [DEICER] - BATTERY)

NG

REPLACE FRONT WIPER DEICER RELAY (DEICER)

10.CHECK HARNESS AND CONNECTOR (FRONT WIPER DEICER RELAY [DEICER] - BATTERY)
a.
B472073C02
0.156,0.115 0.469,0.313 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Front Wiper Deicer Relay [DEICER])


Remove the front wiper deicer relay (DEICER) from the No. 1 front compartment relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Front wiper deicer relay (DEICER) terminal 2 - Body ground Ignition switch ON 11 to 14 V
front wiper deicer relay (DEICER) terminal 3 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FRONT WIPER DEICER RELAY [DEICER] - AIR CONDITIONING AMPLIFIER ASSEMBLY AND WINDSHIELD GLASS [WINDSHIELD DEICER WIRE])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (FRONT WIPER DEICER RELAY [DEICER] - AIR CONDITIONING AMPLIFIER ASSEMBLY AND WINDSHIELD GLASS [WINDSHIELD DEICER WIRE])
a.

Remove the front wiper deicer relay (DEICER) from the No. 1 front compartment relay block.


b.

Disconnect the A45 windshield glass (windshield deicer wire) connector.


c.

Disconnect the D81 air conditioning amplifier assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A45,D81)Location & Routing

Click Connector(A45)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Wiper Deicer (Windshield Glass)

Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assembly

Front wiper deicer relay (DEICER) terminal 5 - A45-1 (B) Always Below 1 Ω
Front wiper deicer relay (DEICER) terminal 1 - D81-22 (FDEF) Always Below 1 Ω
Front wiper deicer relay (DEICER) terminal 5 or A45-1 (B) - Body ground Always 10 kΩ or higher
Front wiper deicer relay (DEICER) terminal 1 or D81-22 (FDEF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR