Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE COMPARTMENT DOOR OPENER SYSTEM
RM37H0E _59 Vehicle Exterior _095314 DOOR / HATCH _0453655 LUGGAGE COMPARTMENT DOOR OPENER SYSTEM J

DOOR / HATCH  LUGGAGE COMPARTMENT DOOR OPENER SYSTEM  Luggage Compartment Door Opener does not Operate Using Any Operation  


DESCRIPTION

The luggage compartment door opener system controls the main body ECU (multiplex network body ECU) and operates the luggage compartment door lock assembly (closer motor). If the luggage compartment door opener system does not operate using any of the operations, a malfunction related to the luggage compartment door opener system operation conditions or main body ECU (multiplex network body ECU) malfunction are possible causes.

WIRING DIAGRAM

E456442E01
0.917,0.396 1.813,0.604 0.896,0.208 10 false TRUNK OPN 2.125,2.25 3.271,2.604 1.146,0.354 10 false Trunk Open Relay (TRUNK OPN) 0.969,5.76 3.688,6.01 2.719,0.25 10 false Luggage Compartment Door Lock Assembly 0.99,5.563 1.302,5.76 0.313,0.198 10 false K1 0.792,7.49 3.833,7.708 3.042,0.219 10 false Luggage Door Opening Cancel Switch Assembly 0.802,7.313 1.26,7.51 0.458,0.198 10 false D87 5.448,7.708 7.083,8.063 1.635,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 2.479,0.167 3.917,0.385 1.438,0.219 10 false from Auxiliary Battery 4.365,4.469 5.583,4.865 1.219,0.396 10 false Driver Side Junction Block Assembly 3.75,1.208 4.063,1.406 0.313,0.198 10 false 4F 3.729,3.708 4.042,3.906 0.313,0.198 10 false 4H 5.542,3.708 5.698,3.906 0.156,0.198 10 false A 5.542,1.208 5.698,1.406 0.156,0.198 10 false A 5.885,1.198 6.344,1.396 0.458,0.198 10 false TR+ 5.885,3.708 6.344,3.906 0.458,0.198 10 false LGCY 5.885,6.906 6.5,7.135 0.615,0.229 10 false TMSW 5.469,6.906 5.927,7.104 0.458,0.198 10 false D11 5.521,6.688 5.833,6.885 0.313,0.198 10 false 27 5.542,0.979 5.698,1.177 0.156,0.198 10 false 6 5.552,3.479 5.708,3.677 0.156,0.198 10 false 4 3.75,0.969 4.063,1.167 0.313,0.198 10 false 32 3.75,3.49 4.063,3.688 0.313,0.198 10 false 27 1.281,1.083 1.438,1.281 0.156,0.198 10 false 1 1.281,1.542 1.438,1.74 0.156,0.198 10 false 5 2.365,1.083 2.521,1.281 0.156,0.198 10 false 2 2.365,1.542 2.521,1.74 0.156,0.198 10 false 3 1.948,2.156 2.104,2.354 0.156,0.198 10 false 4 1.146,4.594 1.302,4.792 0.156,0.198 10 false 3 1.146,4.979 1.302,5.177 0.156,0.198 10 false 1 3.26,4.979 3.417,5.177 0.156,0.198 10 false 2 1.396,4.594 1.708,4.792 0.313,0.198 10 false D+ 1.396,4.979 1.708,5.177 0.313,0.198 10 false B 2.99,4.979 3.302,5.177 0.313,0.198 10 false E 2.99,6.792 3.302,6.99 0.313,0.198 10 false B 1.406,6.792 1.719,6.99 0.313,0.198 10 false L 3.25,6.792 3.406,6.99 0.156,0.198 10 false 2 1.156,6.781 1.313,6.979 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check power door lock control system operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Power door lock control system is normal.



Result:
Proceed to
OK
NG



OK

2.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

NG

2.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check wireless door lock control system operation.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Wireless door lock control system is normal.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS

NG

3.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Trunk and Back-Door Open Luggage door condition signal OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Trunk and Back-Door Open
50004 123 3
OK:

The luggage door operates normally according to the GTS operation.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS

NG

7.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
4.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Trunk Main SW Luggage door opening cancel switch assembly signal OFF or ON OFF: Luggage door opening cancel switch assembly off
ON: Luggage door opening cancel switch assembly on
-
Luggage Courtesy SW Luggage door courtesy light switch signal OFF or ON OFF: Luggage door closed
ON: Luggage door open
-
Body Electrical > Main Body > Data List
Tester Display
Trunk Main SW
Luggage Courtesy SW
50003 123 94,53
OK:

The Data List item changes according to the operation of the luggage door opening cancel switch assembly.



Result:
Result Proceed to
The Data List changes according to each operation A
The Data List "Trunk Main SW" does not change according to the luggage door opening cancel switch assembly being operated B
The Data List "Luggage Courtesy SW" does not change according to the luggage door opening or closing C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

5.INSPECT LUGGAGE DOOR OPENING CANCEL SWITCH ASSEMBLY

C

5.INSPECT LUGGAGE DOOR OPENING CANCEL SWITCH ASSEMBLY

OK

6.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR OPENING CANCEL SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE LUGGAGE DOOR OPENING CANCEL SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR OPENING CANCEL SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the D87 luggage door opening cancel switch assembly connector.


b.

Disconnect the D11 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D87,D11)Location & Routing

Click Connector(D87)Instrument Panel>Instrument Panel Wire>Luggage Door Opening Switch Assembly Cancel

Click Connector(D11)Instrument Panel>Instrument Panel Wire>Main Body ECU

D87-2 (B) - D11-27 (TMSW) Always Below 1 Ω
D87-1 (L) - Body ground Always Below 1 Ω
D87-2 (B) or D11-27 (TMSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

OK

8.INSPECT TRUNK OPEN RELAY (TRUNK OPN)

NG

REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

8.INSPECT TRUNK OPEN RELAY (TRUNK OPN)

Click hereVehicle Exterior>DOOR / HATCH>RELAY>INSPECTION

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - TRUNK OPEN RELAY [TRUNK OPN] AND BODY GROUND)

NG

REPLACE TRUNK OPEN RELAY (TRUNK OPN)

9.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - TRUNK OPEN RELAY [TRUNK OPN] AND BODY GROUND)
a.

Disconnect the K1 luggage compartment door lock assembly connector.


b.

Remove the trunk open relay (TRUNK OPN) from the Luggage room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K1)Location & Routing

Click Connector(K1)Body>No. 1 Back Door Wire>Luggage Compartment Door Lock Assembly

K1-1 (B) - Trunk open relay (TRUNK OPN) terminal 3 Always Below 1 Ω
K1-2 (E) - Body ground Always Below 1 Ω
K1-1 (B) or Trunk open relay (TRUNK OPN) terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (TRUNK OPEN RELAY [TRUNK OPN] - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (TRUNK OPEN RELAY [TRUNK OPN] - BATTERY AND BODY GROUND)
a.
B403332C04
0.115,0.063 0.427,0.219 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Trunk Open Relay [TRUNK OPN])


Remove the trunk open relay (TRUNK OPN) from the Luggage room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Trunk open relay (TRUNK OPN) terminal 4 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Trunk open relay (TRUNK OPN) terminal 1 - Body ground Ignition switch off 11 to 14 V
Trunk open relay (TRUNK OPN) terminal 5 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (TRUNK OPEN RELAY [TRUNK OPN] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (TRUNK OPEN RELAY [TRUNK OPN] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Remove the trunk open relay (TRUNK OPN) from the Luggage room relay block assembly.


b.

Disconnect the 4F driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Trunk open relay (TRUNK OPN) terminal 2 - 4F-32 Always Below 1 Ω
Trunk open relay (TRUNK OPN) terminal 2 or 4F-32 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.
E364899E02
1.448,0.219 1.906,0.5 0.458,0.281 1.49,1.99 1.885,2.281 0.396,0.292 0.76,2.583 1,3.104 1,3.104 1.24,3.104 true 1.594,0.281 1.917,0.583 0.323,0.302 10 false 4F 1.646,2.052 1.802,2.25 0.156,0.198 10 false A 1.344,3 1.802,3.198 0.458,0.198 10 false TR+

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-32- A-6 (TR+) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY