This DTC is stored when the sliding roof drive gear sub-assembly detects that the map light assembly is stuck for 30 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B2342 | Switch Failure | Sliding roof drive gear sub-assembly detects map light assembly is stuck for 30 seconds or more. | ·
Sliding roof drive gear sub-assembly ·
Map light assembly ·
Harness or connector |
Sliding Roof | A |
Refer to DTC B2341.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>B2341
The roof sunshade system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to How to Proceed with Troubleshooting.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch Failure(Past) | Open switch failure signal (Past) | ON or OFF | ON: Roof sunshade open signal failure (Past)
OFF: No roof sunshade open signal failure (Past) |
- |
| Close Switch Failure(Past) | Close switch failure signal (Past) | ON or OFF | ON: Roof sunshade close signal failure (Past)
OFF: No roof sunshade close signal failure (Past) |
- |
| Tester Display |
|---|
| Open Switch Failure(Past) |
| Close Switch Failure(Past) |
| Result | Proceed to |
|---|---|
| The value of Open Switch Failure(Past) and Close Switch Failure(Past) are OFF | A |
| The value of Open Switch Failure(Past) or Close Switch Failure(Past) is not OFF | B |
A
B
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch Failure(Current) | Open switch failure signal (Current) | ON or OFF | ON: Roof sunshade open signal failure (Current)
OFF: No roof sunshade open signal failure (Current) |
- |
| Close Switch Failure(Current) | Close switch failure signal (Current) | ON or OFF | ON: Roof sunshade close signal failure (Current)
OFF: No roof sunshade close signal failure (Current) |
- |
| Tester Display |
|---|
| Open Switch Failure(Current) |
| Close Switch Failure(Current) |
| Result | Proceed to |
|---|---|
| The value of Open Switch Failure(Current) and Close Switch Failure(Current) are OFF | A |
| The value of Open Switch Failure(Current) or Close Switch Failure(Current) is not OFF | B |
A
B
Pre-procedure1
Disconnect the H4 sliding roof drive gear sub-assembly connector.
Disconnect the H8 roof shade switch (map light assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H4,H8)Location & Routingewd_type=routing;type=c,c;code=H4,H8 Click Connector(H4)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Sub-Assembly)ewd_type=component;type=c;code=H4;pinno=5,9 Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=H8;pinno=11,12 |
||
| H4-5 (OPN) or H8-11 (OPN) - Body ground | Always | 10 kΩ or higher |
| H4-9 (CLS) or H8-12 (CLS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG