Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF SUNSHADE SYSTEM
RM37H0E _58 Vehicle Interior _095304 INTERIOR PANELS / TRIM _0454452 ROOF SUNSHADE SYSTEM C

INTERIOR PANELS / TRIM  ROOF SUNSHADE SYSTEM  B2341  Sensor (Motor) Failure  B2344  Position Failure  


DESCRIPTION

When the sliding roof drive gear sub-assembly detects a motor malfunction and the roof sunshade operation is stopped, DTC B2341 is stored.

When the sliding roof drive gear sub-assembly detects a gear position malfunction and the roof sunshade operation is stopped, DTC B2344 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2341 Sensor (Motor) Failure Sensor (motor) failure (When the sliding roof drive gear sub-assembly enters fail-safe mode due to a problem with the motor)
·

Sliding roof drive gear sub-assembly

·

Map light assembly

·

Harness or connector


Sliding Roof A
B2344 Position Failure Position failure (When the sliding roof drive gear sub-assembly enters fail-safe mode due to a problem with the gear position)
·

Sliding roof drive gear sub-assembly

·

Map light assembly

·

Harness or connector


Sliding Roof A

WIRING DIAGRAM

E283515E12
1.781,1.99 3.635,2.292 1.854,0.302 10 false H8 1.813,2.135 3.26,2.771 1.448,0.635 10 false Roof Sunshade Switch (Map Light Assembly) 2.948,1.448 4.802,1.75 1.854,0.302 10 false CLS 2.938,0.969 4.792,1.271 1.854,0.302 10 false OPN 2.031,0.948 3.885,1.25 1.854,0.302 10 false GND 1.75,0.948 3.604,1.25 1.854,0.302 10 false 19 3.385,0.958 3.823,1.365 0.438,0.406 10 false 11 3.385,1.458 3.823,1.865 0.438,0.406 10 false 12 5.427,0.979 5.875,1.844 0.448,0.865 10 false 5 5.427,1.448 5.875,2.313 0.448,0.865 10 false 9 5.427,1.885 5.875,2.75 0.448,0.865 10 false 2 5.635,2 6.458,2.469 0.823,0.469 10 false E 5.635,1.521 6.458,1.99 0.823,0.469 10 false CLS 5.625,1.052 6.448,1.521 0.823,0.469 10 false OPN 5.281,2.74 7.156,3.198 1.875,0.458 10 false H4 5.271,2.938 6.76,3.698 1.49,0.76 10 false Sliding Roof Drive Gear Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, it requires initialization.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION

·

The roof sunshade system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CUSTOMIZE SETTING
a.

Select the setting by referring to the table below.

Slide Roof
Tester Display Description Default Setting ECU
Front SW Auto Operation This function is used to enable or disable the auto operation. ON 0:OFF,1:ON Sliding roof drive gear sub-assembly
50006 10

Result:
Result Proceed to
Front SW Auto Operation are ON A
Front SW Auto Operation are OFF B



A

2.CHECK ROOF SUNSHADE OPERATION

B

2.CHECK ROOF SUNSHADE OPERATION
a.

Check the roof sunshade auto operation.

HINT:

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>OPERATION CHECK


OK:

Auto operation operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

4.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
3.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Sliding Roof > Clear DTCs
50002 147

Procedure1

a.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


Post-procedure1

a.

None



A

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

4.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
a.

Check that the sliding roof drive gear sub-assembly can be initialized.

HINT:

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION


OK:

Sliding roof drive gear sub-assembly can be initialized.



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DTC

NG

6.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - ROOF SUNSHADE SWITCH [MAP LIGHT ASSEMBLY] AND BODY GROUND)
5.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Sliding Roof > Clear DTCs
50002 147

Procedure1

a.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


Post-procedure1

a.

None



A

END (MALFUNCTION DUE TO INITIALIZATION FAILURE)

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - ROOF SUNSHADE SWITCH [MAP LIGHT ASSEMBLY] AND BODY GROUND)

Pre-procedure1

a.

Disconnect the H4 sliding roof drive gear sub-assembly connector.


b.

Disconnect the H8 roof sunshade switch (map light assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H4,H8)Location & Routing

Click Connector(H4)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Sub-Assembly)

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H4-9 (CLS) - H8-12 (CLS) Always Below 1 Ω
H4-9 (CLS) or H8-12 (CLS) - Body ground Always 10 kΩ or higher
H4-5 (OPN) - H8-11 (OPN) Always Below 1 Ω
H4-5 (OPN) or H8-11 (OPN) - Body ground Always 10 kΩ or higher
H4-2 (E) - Body ground Always Below 1 Ω
H8-19 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

7.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT MAP LIGHT ASSEMBLY

OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

REPLACE ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY)