If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, telematics transceiver or speakers.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
If sound cannot be heard from any speaker, inspect all of them.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly and front No. 3 speaker assembly | A |
| Front No. 2 speaker assembly | B |
| Rear No. 2 speaker assembly and rear speaker assembly | C |
| Rear No. 3 speaker assembly | D |
| No. 1 speaker with box assembly | E |
A
B
C
D
E
Disconnect the G54 stereo component amplifier assembly connector.
Disconnect the E1 and E19 front No. 1 speaker assembly connectors.
Disconnect the D88 and D89 front No. 3 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G54,D89,E19,D88,E1)Location & Routingewd_type=routing;type=c,c,c,c,c;code=G54,D89,E19,D88,E1 Click Connector(G54)Body>Floor Wire / No. 3 Floor Wire>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=G54;pinno=4,19,15,30 Click Connector(D89)Instrument Panel>Instrument Panel Wire>Front No. 3 Speaker Assembly LHewd_type=component;type=c;code=D89;pinno=4,2,3,1 Click Connector(E19)Body>Front Door Wire LH / Front Door Wire RH>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=E19;pinno=2,1 Click Connector(D88)Instrument Panel>Instrument Panel Wire>Front No. 3 Speaker Assembly RHewd_type=component;type=c;code=D88;pinno=4,2,3,1 Click Connector(E1)Body>Front Door Wire LH / Front Door Wire RH>Front No. 1 Speaker Assembly RHewd_type=component;type=c;code=E1;pinno=2,1 |
||
| G54-4 (FL+) - D89-4 (TWL+) | Always | Below 1 Ω |
| G54-19 (FL-) - D89-2 (TWL-) | Always | Below 1 Ω |
| D89-3 (+) - E19-2 (+) | Always | Below 1 Ω |
| D89-1 (-) - E19-1 (-) | Always | Below 1 Ω |
| G54-15 (FR+) - D88-4 (TWR+) | Always | Below 1 Ω |
| G54-30 (FR-) - D88-2 (TWR-) | Always | Below 1 Ω |
| D88-3 (+) - E1-2 (+) | Always | Below 1 Ω |
| D88-1 (-) - E1-1 (-) | Always | Below 1 Ω |
| G54-4 (FL+) - Body ground | Always | 10 kΩ or higher |
| G54-19 (FL-) - Body ground | Always | 10 kΩ or higher |
| D89-3 (+) - Body ground | Always | 10 kΩ or higher |
| D89-1 (-) - Body ground | Always | 10 kΩ or higher |
| G54-15 (FR+) - Body ground | Always | 10 kΩ or higher |
| G54-30 (FR-) - Body ground | Always | 10 kΩ or higher |
| D88-3 (+) - Body ground | Always | 10 kΩ or higher |
| D88-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 3 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G54 stereo component amplifier assembly connector.
Disconnect the D82 and D83 front No. 2 speaker assembly connectors.
Disconnect the D59 front No. 2 speaker assembly CTR connector.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G54,D82,D83,D59)Location & Routingewd_type=routing;type=c,c,c,c;code=G54,D82,D83,D59 Click Connector(G54)Body>Floor Wire / No. 3 Floor Wire>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=G54;pinno=6,21,5,20,13,28 Click Connector(D82)Instrument Panel>Instrument Panel Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=D82;pinno=2,1 Click Connector(D83)Instrument Panel>Instrument Panel Wire>Front No .2 Speaker Assembly LHewd_type=component;type=c;code=D83;pinno=2,1 Click Connector(D59)Instrument Panel>Instrument Panel Wire>Front No. 2 Speaker Assemblyewd_type=component;type=c;code=D59;pinno=2,1 |
||
| G54-6 (TWR+) - D82-2 (+) | Always | Below 1 Ω |
| G54-21 (TWR-) - D82-1 (-) | Always | Below 1 Ω |
| G54-5 (TWL+) - D83-2 (+) | Always | Below 1 Ω |
| G54-20 (TWL-) - D83-1 (-) | Always | Below 1 Ω |
| G54-13 (CTR+) - D59-2 (+) | Always | Below 1 Ω |
| G54-28 (CTR-) - D59-1 (-) | Always | Below 1 Ω |
| G54-6 (TWR+) - Body ground | Always | 10 kΩ or higher |
| G54-21 (TWR-) - Body ground | Always | 10 kΩ or higher |
| G54-5 (TWL+) - Body ground | Always | 10 kΩ or higher |
| G54-20 (TWL-) - Body ground | Always | 10 kΩ or higher |
| G54-13 (CTR+) - Body ground | Always | 10 kΩ or higher |
| G54-28 (CTR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G54 stereo component amplifier assembly connector.
Disconnect the F7 and F18 rear speaker assembly connectors.
Disconnect the F6 and F17 rear No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G54,F6,F7,F17,F18)Location & Routingewd_type=routing;type=c,c,c,c,c;code=G54,F6,F7,F17,F18 Click Connector(G54)Body>Floor Wire / No. 3 Floor Wire>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=G54;pinno=12,27,11,26 Click Connector(F6)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear No. 2 Speaker Assembly RHewd_type=component;type=c;code=F6;pinno=4,2,3,1 Click Connector(F7)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=F7;pinno=2,1 Click Connector(F17)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear No. 2 Speaker Assembly LHewd_type=component;type=c;code=F17;pinno=4,2,3,1 Click Connector(F18)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=F18;pinno=2,1 |
||
| G54-12 (RR+) - F6-4 (+TW) | Always | Below 1 Ω |
| G54-27 (RR-) - F6-2 (-TW) | Always | Below 1 Ω |
| F6-3 (+) - F7-2 (+) | Always | Below 1 Ω |
| F6-1 (-) - F7-1 (-) | Always | Below 1 Ω |
| G54-11 (RL+) - F17-4 (+TW) | Always | Below 1 Ω |
| G54-26 (RL-) - F17-2 (-TW) | Always | Below 1 Ω |
| F17-3 (+) - F18-2 (+) | Always | Below 1 Ω |
| F17-1 (-) - F18-1 (-) | Always | Below 1 Ω |
| G54-12 (RR+) - Body ground | Always | 10 kΩ or higher |
| G54-27 (RR-) - Body ground | Always | 10 kΩ or higher |
| F6-3 (+) - Body ground | Always | 10 kΩ or higher |
| F6-1 (-) - Body ground | Always | 10 kΩ or higher |
| G54-11 (RL+) - Body ground | Always | 10 kΩ or higher |
| G54-26 (RL-) - Body ground | Always | 10 kΩ or higher |
| F17-3 (+) - Body ground | Always | 10 kΩ or higher |
| F17-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left rear speaker is defective, inspect by interchanging the right one with the left one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G54 stereo component amplifier assembly connector.
Disconnect the G17 and G18 rear No. 3 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G54,G17,G18)Location & Routingewd_type=routing;type=c,c,c;code=G54,G17,G18 Click Connector(G54)Body>Floor Wire / No. 3 Floor Wire>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=G54;pinno=10,25,9,24 Click Connector(G17)Body>Floor Wire / No. 3 Floor Wire>Rear No. 3 Speaker Assembly RHewd_type=component;type=c;code=G17;pinno=2,1 Click Connector(G18)Body>Floor Wire / No. 3 Floor Wire>Rear No. 3 Speaker Assembly LHewd_type=component;type=c;code=G18;pinno=2,1 |
||
| G54-10 (SR+) - G17-2 (+) | Always | Below 1 Ω |
| G54-25 (SR-) - G17-1 (-) | Always | Below 1 Ω |
| G54-9 (SL+) - G18-2 (+) | Always | Below 1 Ω |
| G54-24 (SL-) - G18-1 (-) | Always | Below 1 Ω |
| G54-10 (SR+) - Body ground | Always | 10 kΩ or higher |
| G54-25 (SR-) - Body ground | Always | 10 kΩ or higher |
| G54-9 (SL+) - Body ground | Always | 10 kΩ or higher |
| G54-24 (SL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G54 stereo component amplifier assembly connector.
Disconnect the G19 rear No. 1 speaker with box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G54,G19)Location & Routingewd_type=routing;type=c,c;code=G54,G19 Click Connector(G54)Body>Floor Wire / No. 3 Floor Wire>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=G54;pinno=8,23,7,22 Click Connector(G19)Body>Floor Wire / No. 3 Floor Wire>No. 1 Speaker with Box Assemblyewd_type=component;type=c;code=G19;pinno=4,3,2,1 |
||
| G54-8 (WF1+) - G19-4 (WF1+) | Always | Below 1 Ω |
| G54-23 (WF1-) - G19-3 (WF1-) | Always | Below 1 Ω |
| G54-7 (WF2+) - G19-2 (WF2+) | Always | Below 1 Ω |
| G54-22 (WF2-) - G19-1 (WF2-) | Always | Below 1 Ω |
| G54-8 (WF1+) - Body ground | Always | 10 kΩ or higher |
| G54-23 (WF1-) - Body ground | Always | 10 kΩ or higher |
| G54-7 (WF2+) - Body ground | Always | 10 kΩ or higher |
| G54-22 (WF2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG