Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM C

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P085011  Park/Neutral Switch Circuit Short to Ground  P085015  Park/Neutral Switch Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

Instead of having a parking position as one of the positions as on a conventional shift lever, a P position switch (parking switch) is provided independently under the shift lever. The switch is a momentary type, in which the button does not lock mechanically.

The P position switch (parking switch) contains resistors R1, R2, R3 and R4. When the P position switch (parking switch) is not pressed, the switch provides a combined resistance of R3 and R4; and when the P position switch (parking switch) is pressed, the switch provides a combined resistance of R1, R2, R3 and R4. The voltage at the P1 terminal of the shift control ECU varies with the changes in the resistance of the switch. The shift control ECU determines the P position switch (parking switch) operation according to this resistance signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P085011 Park/Neutral Switch Circuit Short to Ground 1. 0.5 seconds or more elapse after turning ignition switch to ON (READY) with auxiliary battery voltage 10 V or higher, P1 terminal voltage of P position switch circuit is continuously lower than specified value for 2 seconds or more
(1 trip detection logic)
·

P position switch (parking switch)

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A
P085015 Park/Neutral Switch Circuit Short to Auxiliary Battery or Open 1. 0.5 seconds or more elapse after turning ignition switch to ON (READY) with auxiliary battery voltage 10 V or higher, P1 terminal voltage of P position switch circuit is continuously higher than specified value for 2 seconds or more
(1 trip detection logic)
·

P position switch (parking switch)

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A

Related Data List
DTC No. Data List
P085011
·

P Position Switch Terminal Voltage (Gear Shift Control Module)*

·

BATT Voltage for Gear Shift Control Module


P085015

*: While the P position switch (parking switch) is being pushed, the value for Data List item "P Position Switch Terminal Voltage (Gear Shift Control Module)" will decrease.

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY


1.

Turn the ignition switch to ON (READY).

2.

Depress the brake pedal and move the shift lever to select neutral (N).

3.

Push the P position switch (parking switch) to select park (P).


WIRING DIAGRAM

C372828E06
1.021,1.844 3.958,2.073 2.938,0.229 10 false P Position Switch (Parking Switch) 1.021,1.656 1.479,1.854 0.458,0.198 10 false D17 1.365,1.021 1.677,1.219 0.313,0.198 10 false R4 2.188,0.667 2.5,0.865 0.313,0.198 10 false R1 2.188,1.021 2.5,1.219 0.313,0.198 10 false R2 2.823,1.354 3.135,1.552 0.313,0.198 10 false R3 0.865,0.74 1.177,0.938 0.313,0.198 10 false 9 1.094,0.74 1.25,0.938 0.156,0.198 10 false E 3.375,0.729 3.531,0.927 0.156,0.198 10 false S 3.583,0.729 3.896,0.927 0.313,0.198 10 false 2 4.75,0.75 5.063,0.948 0.313,0.198 10 false 10 5.031,0.75 5.344,0.948 0.313,0.198 10 false P1 4.969,1.729 5.427,1.927 0.458,0.198 10 false D93 4.979,1.906 6.823,2.073 1.844,0.167 10 false Shift Control ECU

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION


PROCEDURE

1.INSPECT P POSITION SWITCH (PARKING SWITCH)
a.

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P POSITION SWITCH (PARKING SWITCH))

NG

2.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P POSITION SWITCH (PARKING SWITCH))

Pre-procedure1

a.

Disconnect the D93 shift control ECU connector.


b.

Disconnect the D17 P position switch (parking switch) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D93,D17)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

Click Connector(D17)Instrument Panel>Instrument Panel Wire>Parking Switch

D93-10 (P1) - D17-2 (S) Always Below 1 Ω
D93-10 (P1) or D17-2 (S) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D17 P position switch (parking switch) connector.


b.

Reconnect the D93 shift control ECU connector.



OK

3.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (PARKING SWITCH) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (PARKING SWITCH) - BODY GROUND)

Pre-procedure1

a.

Disconnect the D17 P position switch (parking switch) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(D17)Location & Routing

Click Connector(D17)Instrument Panel>Instrument Panel Wire>Parking Switch

D17-9 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D17 P position switch (parking switch) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR