Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM C

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P176A87  Lost Communication with Fail Safe Signal (Gear Shift Control Module "A") Missing Message  


DESCRIPTION

The shift control ECU sends SBFS (fail-safe) signals to the EV control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P176A87 Lost Communication with Fail Safe Signal (Gear Shift Control Module "A") Missing Message The SBFS (fail-safe) signals sent from the shift control ECU cannot be received by the EV control ECU continuously for 2 seconds or more.
(1 trip detection logic)
·

Shift control ECU

·

EV control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY


1.

Turn the ignition switch to ON (READY) and wait for 2 minutes or more.


WIRING DIAGRAM

C453872E01
0.677,2.979 1.135,3.177 0.458,0.198 10 false D92 0.677,3.146 2.813,3.313 2.135,0.167 10 false Shift Control ECU 4.75,1.823 5.208,2.021 0.458,0.198 10 false D15 5.063,3.115 6.885,3.417 1.823,0.302 10 false EV Control ECU 2.208,1.719 2.365,1.917 0.156,0.198 10 false 3 4.792,1.625 5.104,1.823 0.313,0.198 10 false 10 1.75,1.74 2.521,1.948 0.771,0.208 10 false SBFS 5.115,1.719 5.771,1.885 0.656,0.167 10 false SBFS 4.76,2.5 5.219,2.698 0.458,0.198 10 false A17 5.177,2.521 5.49,2.719 0.313,0.198 10 false E1 4.844,2.313 5,2.51 0.156,0.198 10 false 4 4.375,2.052 4.688,2.25 0.313,0.198 10 false *1 2.792,0.604 4.479,0.802 1.688,0.198 10 false *1: for LHD 2.802,0.958 4.49,1.156 1.688,0.198 10 false *2: for RHD 4.385,1.823 4.698,2.021 0.313,0.198 10 false A8 4.385,1.625 4.698,1.823 0.313,0.198 10 false 10 4.781,2.042 5.094,2.24 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION


PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK SHIFT CONTROL ECU (CHECK SBFS TERMINAL WAVEFORM)

B

4.CHECK SHIFT CONTROL ECU (CHECK SBFS TERMINAL WAVEFORM)
2.CHECK SHIFT CONTROL ECU (CHECK SBFS TERMINAL WAVEFORM)

Pre-procedure1

a.
C449917C05
0.698,0.302 1.031,0.51 0.333,0.208 2.427,0.302 2.76,0.51 0.333,0.208 2.344,1.771 2.354,1.177 true 0.927,1.813 0.948,1.031 true 2.188,1.844 2.646,2.01 0.458,0.167 10 false SBFS 0.76,0.333 1.219,0.531 0.458,0.198 10 false A17 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.167,2.313 0.479,2.51 0.313,0.198 10 false *b 2.927,3.646 3.385,3.844 0.458,0.198 10 false GND 0.823,1.865 1.063,2.01 0.24,0.146 10 false E1 2.5,0.333 2.958,0.531 0.458,0.198 10 false A8
*a Front view of wire harness connector
(to EV Control ECU)
*b Waveform (Fail-safe signal)


Disconnect the EV control ECU connector.


Procedure1

a.

Connect an oscilloscope between the EV control ECU connector terminals specified in the table below.


b.

Turn the ignition switch to ON and measure the waveform.

Tester Connection Condition Equipment Setting

Click Location & Routing(A8,A17)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-10 (SBFS) - A17-4 (E1) Ignition switch ON 10 V/DIV., 20 ms./DIV.

NOTICE:

Turning the ignition switch to ON with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

The waveforms differ when the shift control ECU is malfunctioning.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the EV control ECU connector.



OK

NG

3.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - EV CONTROL ECU)
3.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the D92 shift control ECU connector.


b.

Disconnect the A8 EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A8,D92)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

A8-10 (SBFS) - D92-3 (SBFS) Always Below 1 Ω
A8-10 (SBFS) or D92-3 (SBFS) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the A8 EV control ECU connector.


b.

Reconnect the D92 shift control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SHIFT CONTROL ECU (CHECK SBFS TERMINAL WAVEFORM)

Pre-procedure1

a.
C449917C06
0.698,0.302 1.031,0.51 0.333,0.208 2.406,0.271 2.74,0.479 0.333,0.208 2.344,1.771 2.354,1.177 true 0.927,1.813 0.948,1.031 true 2.188,1.844 2.646,2.01 0.458,0.167 10 false SBFS 0.771,0.344 1.229,0.542 0.458,0.198 10 false A17 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.167,2.313 0.479,2.51 0.313,0.198 10 false *b 2.927,3.646 3.385,3.844 0.458,0.198 10 false GND 0.823,1.865 1.063,2.01 0.24,0.146 10 false E1 2.458,0.313 2.917,0.51 0.458,0.198 10 false D15
*a Front view of wire harness connector
(to EV Control ECU)
*b Waveform (Fail-safe signal)


Disconnect the EV control ECU connector.


Procedure1

a.

Connect an oscilloscope between the EV control ECU connector terminals specified in the table below.


b.

Turn the ignition switch to ON and measure the waveform.

Tester Connection Condition Equipment Setting

Click Location & Routing(D15,A17)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

D15-10 (SBFS) - A17-4 (E1) Ignition switch ON 10 V/DIV., 20 ms./DIV.

NOTICE:

Turning the ignition switch to ON with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

The waveforms differ when the shift control ECU is malfunctioning.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the EV control ECU connector.



OK

NG

5.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - EV CONTROL ECU)
5.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the D92 shift control ECU connector.


b.

Disconnect the D15 EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D15,D92)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D15-10 (SBFS) - D92-3 (SBFS) Always Below 1 Ω
D15-10 (SBFS) or D92-3 (SBFS) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D15 EV control ECU connector.


b.

Reconnect the D92 shift control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR