Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM C

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P176D12  IG2 Signal (Gear Shift Control Module "A") Circuit Short to Auxiliary Battery  


DESCRIPTION

The shift control ECU detects that the IG2 signal is stuck ON by comparing it with the IG control status signal sent from the certification ECU (smart key ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P176D12 IG2 Signal (Gear Shift Control Module "A") Circuit Short to Auxiliary Battery 8 seconds elapse after turning ignition switch to ON (READY) and then turn ignition switch off. Even when IG control status signal from certification ECU (smart key ECU assembly) is OFF, IG2 signal is ON continuously for 10 seconds or more
(1 trip detection logic)
·

Certification ECU (smart key ECU assembly)

·

Shift Control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 15 seconds or more.

2.

Turn the ignition switch off and wait for 2 minutes or more.


WIRING DIAGRAM

for LHD:
C453761E03
0.375,0.813 1.885,1.031 1.51,0.219 10 false from Auxiliary Battery 2.99,0.656 3.146,0.854 0.156,0.198 10 false 3 3.979,0.667 4.135,0.865 0.156,0.198 10 false 5 3,1.083 3.156,1.281 0.156,0.198 10 false 2 3.958,1.125 4.115,1.323 0.156,0.198 10 false 1 4.25,0.938 5.063,1.115 0.813,0.177 10 false IG2 P NO.2 5.24,0.677 5.552,0.875 0.313,0.198 10 false 27 5.542,0.708 6,0.906 0.458,0.198 10 false IG2 5.51,1.417 5.969,1.615 0.458,0.198 10 false D92 5.51,1.625 6.813,1.844 1.302,0.219 10 false Shift Control ECU 3.344,1.646 3.802,1.854 0.458,0.208 10 false IG2 P 0.885,3.448 1.865,3.635 0.979,0.188 10 false LUG-IG1 NO.1 0.823,2.396 0.979,2.594 0.156,0.198 10 false 3 1.833,2.406 1.99,2.604 0.156,0.198 10 false 5 0.813,2.833 0.969,3.031 0.156,0.198 10 false 1 1.823,2.844 1.979,3.042 0.156,0.198 10 false 2 0.854,1.417 1.833,1.604 0.979,0.188 10 false LUG-IG1 NO.1 3.302,2.958 3.615,3.156 0.313,0.198 10 false 4H 3.292,2.729 3.604,2.938 0.313,0.208 10 false 10 5.521,2.969 5.833,3.167 0.313,0.198 10 false 4D 5.521,2.76 5.833,2.958 0.313,0.198 10 false 18 0.323,5.24 0.781,5.438 0.458,0.198 10 false D86 2.25,4.854 2.563,5.052 0.313,0.198 10 false 17 1.74,4.979 2.354,5.177 0.615,0.198 10 false IG1D 0.313,5.51 3.625,5.813 3.313,0.302 10 false Certification ECU (Smart Key ECU Assembly) 3.385,3.448 6.135,3.74 2.75,0.292 10 false Driver Side Junction Block Assembly

for RHD:
C450041E01
0.375,0.813 1.885,1.031 1.51,0.219 10 false from Auxiliary Battery 2.99,0.656 3.146,0.854 0.156,0.198 10 false 3 3.979,0.667 4.135,0.865 0.156,0.198 10 false 5 3,1.083 3.156,1.281 0.156,0.198 10 false 2 3.958,1.125 4.115,1.323 0.156,0.198 10 false 1 4.25,0.938 5.063,1.115 0.813,0.177 10 false IG2 P NO.2 5.24,0.677 5.552,0.875 0.313,0.198 10 false 27 5.542,0.708 6,0.906 0.458,0.198 10 false IG2 5.51,1.417 5.969,1.615 0.458,0.198 10 false D92 5.51,1.625 6.813,1.844 1.302,0.219 10 false Shift Control ECU 3.344,1.646 3.802,1.854 0.458,0.208 10 false IG2 P 0.927,3.094 1.906,3.281 0.979,0.188 10 false LUG-IG1 NO.1 0.813,2.115 0.969,2.313 0.156,0.198 10 false 3 1.823,2.104 1.979,2.302 0.156,0.198 10 false 5 0.823,2.531 0.979,2.729 0.156,0.198 10 false 1 1.823,2.552 1.979,2.75 0.156,0.198 10 false 2 0.854,1.417 1.833,1.604 0.979,0.188 10 false LUG-IG1 NO.1 2.615,2.677 2.927,2.875 0.313,0.198 10 false 5H 2.635,2.49 2.948,2.688 0.313,0.198 10 false 20 4.854,2.688 5.167,2.885 0.313,0.198 10 false 5D 4.833,2.5 5.146,2.698 0.313,0.198 10 false 16 1.031,5.021 1.344,5.219 0.313,0.198 10 false 4A 1.083,4.823 1.24,5.021 0.156,0.198 10 false 4 3.281,5.021 3.594,5.219 0.313,0.198 10 false 4D 3.271,4.823 3.583,5.021 0.313,0.198 10 false 19 4.823,5.5 5.281,5.698 0.458,0.198 10 false D86 5.063,4.896 5.375,5.094 0.313,0.198 10 false 17 5.375,5 5.99,5.198 0.615,0.198 10 false IG1D 4.813,5.719 7,6.156 2.188,0.438 10 false Certification ECU (Smart Key ECU Assembly) 1.188,5.438 4.063,5.635 2.875,0.198 10 false Driver Side Junction Block Assembly 2.76,3.104 5.698,3.313 2.938,0.208 10 false Passenger Side Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (SHIFT CONTROL ECU CONNECTOR)
a.
for LHD
C452170

for RHD:
C450295

Check the connector connections and contact pressure of the relevant terminals for the shift control ECU connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK SHIFT CONTROL ECU

NG

CONNECT SECURELY

2.CHECK SHIFT CONTROL ECU

Pre-procedure1

a.

Disconnect the D92 shift control ECU connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-27 (IG2) - Body ground Ignition switch off → Ignition switch ON 1 V or less → 8 V or higher


NOTICE:

Turning the ignition switch to ON with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the D92 shift control ECU connector.



OK

3.CHECK DTC OUTPUT

NG

6.INSPECT RELAY (IG2 P)
3.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Check for DTCs and freeze frame data and then write them down.

Powertrain > EV > Trouble Codes
50001 397

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.


b.

Leave the vehicle as is for 60 seconds or more.

NOTICE:
·

Do not connect the GTS.

·

Do not depress the brake pedal.

·

Do not open/close any of the doors.





NEXT

5.CHECK DTC OUTPUT (SIMULATION TEST)
5.CHECK DTC OUTPUT (SIMULATION TEST)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 15 seconds or more.


b.

Turn the ignition switch off and wait for 2 minutes or more.


c.

Turn the ignition switch to ON.


Procedure1

a.

Check if DTCs are output.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P176D12 is not output A
P176D12 is output B



Post-procedure1

a.

Turn the ignition switch off.



A

END

B

6.INSPECT RELAY (IG2 P)

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - LUGGAGE ROOM RELAY BLOCK (IG2 P RELAY))

NG

REPLACE RELAY (IG2 P)

7.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - LUGGAGE ROOM RELAY BLOCK (IG2 P RELAY))

Pre-procedure1

a.

Disconnect the D92 shift control ECU connector.


b.

Remove the IG2 P relay from the luggage room relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-27 (IG2) or luggage room relay block IG2 P relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the IG2 P relay.


b.

Reconnect the D92 shift control ECU connector.



OK

8.INSPECT RELAY (LUG-IG1-NO.1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT RELAY (LUG-IG1-NO.1)
a.

Inspect the LUG-IG1-NO.1 relay.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - LUGGAGE ROOM RELAY BLOCK (IG2 P RELAY))

NG

REPLACE RELAY (LUG-IG1-NO.1)

9.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - LUGGAGE ROOM RELAY BLOCK (IG2 P RELAY))

Pre-procedure1

a.

Remove the IG2 P relay from the luggage room relay block.


b.

Remove the LUG-IG1 NO.1 relay from the luggage room relay block.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (Check for Short):
Tester Connection Condition Specified Condition
Luggage room relay block LUG-IG1 NO.1 relay terminal 3 or luggage room relay block IG2 P relay terminal 2 - Body ground and other terminals Always Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the LUG-IG1 NO.1 relay.


b.

Install the IG2 P relay.



OK

10.CHECK HARNESS AND CONNECTOR (LUG-IG1 NO.1 RELAY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (LUG-IG1 NO.1 RELAY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

Pre-procedure1

a.

Remove the LUG-IG1 NO.1 relay from the luggage room relay block.


b.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Luggage room relay block LUG-IG1 NO.1 relay terminal 2 or D86-17 (IG1D) - Body ground and other terminals Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Install the LUG-IG1 NO.1 relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR