Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455114 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB0  Short to +B in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a short to +B in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1AB0 Short to +B in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time


·

Outer mirror RH (outer rear view mirror indicator RH)

·

Outer mirror retractor RH

·

Harness or connector

·

Blind spot monitor sensor RH

·

Front multiplex network door ECU RH


Blind Spot Monitor Master A

WIRING DIAGRAM

E329056E81
1.573,1.229 1.729,1.427 0.156,0.198 10 false 2 1.563,1.729 1.833,1.938 0.271,0.208 10 false 1 1.375,1.365 1.531,1.563 0.156,0.198 10 false + 1.375,1.823 1.531,2.021 0.156,0.198 10 false - 0.323,2.198 0.979,2.427 0.656,0.229 10 false IND1 0.323,2.344 2.052,2.74 1.729,0.396 10 false Outer Mirror RH (Outer Rear View Mirror Indicator RH) 0.521,3.406 2.219,3.688 1.698,0.281 10 false Outer Mirror Retractor RH 2.948,1.156 3.198,1.344 0.25,0.188 10 false 8 2.906,1.625 3.375,1.823 0.469,0.198 10 false 12 3.104,3.406 4.604,4.094 1.5,0.688 10 false Front Multiplex Network Door ECU RH 4.031,1.354 4.5,1.552 0.469,0.198 10 false BSMI 4.083,1.823 4.552,2.021 0.469,0.198 10 false GND 4.563,1.354 5.031,1.552 0.469,0.198 10 false E7 4.563,1.823 5.031,2.021 0.469,0.198 10 false E7 4.583,1.146 5.052,1.344 0.469,0.198 10 false 21 4.615,1.625 5.083,1.823 0.469,0.198 10 false 1 5.969,1.365 6.438,1.563 0.469,0.198 10 false OMIR 5.781,1.24 6.25,1.438 0.469,0.198 10 false 4 5.823,3.396 6.292,3.594 0.469,0.198 10 false G56 5.813,3.583 7.021,4.198 1.208,0.615 10 false Blind Spot Monitor Sensor RH 2.875,1.344 3.677,1.708 0.802,0.365 10 false z28 3.271,1.354 3.667,1.521 0.396,0.167 10 false BSR 3.302,1.813 3.563,2 0.26,0.188 10 false - 2.875,1.823 3.646,2.104 0.771,0.281 10 false z28

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313

Result:
Result Proceed to
C1AB0 is not output A
C1AB0 is output B



A

B

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

Pre-procedure1

a.

Disconnect the blind spot monitor sensor RH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G56)Location & Routing

Click Connector(G56)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor RH

G56-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

Pre-procedure1

a.

Disconnect the G56 blind spot monitor sensor RH connector.


b.

Disconnect the IND1 outer mirror RH (outer rear view mirror indicator RH) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G56)Location & Routing

Click Connector(G56)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor RH

G56-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

Pre-procedure1

a.

Disconnect the G56 blind spot monitor sensor RH connector.


b.

Disconnect the z28 outer rear view mirror assembly RH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G56)Location & Routing

Click Connector(G56)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor RH

G56-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE OUTER MIRROR RETRACTOR RH

NG

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

Pre-procedure1

a.

Disconnect the G56 blind spot monitor sensor RH connector.


b.

Disconnect the E7 front multiplex network door ECU RH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G56)Location & Routing

Click Connector(G56)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor RH

G56-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR