Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455114 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a short to +B in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1AB1 Short to +B in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time


·

Outer mirror LH (outer rear view mirror indicator LH)

·

Outer mirror retractor LH

·

Harness or connector

·

Blind spot monitor sensor LH

·

Front multiplex network door ECU LH


Blind Spot Monitor Slave A

WIRING DIAGRAM

E329056E82
1.583,1.25 1.74,1.448 0.156,0.198 10 false 2 1.583,1.729 1.74,1.927 0.156,0.198 10 false 1 1.375,1.365 1.531,1.563 0.156,0.198 10 false + 1.375,1.823 1.531,2.021 0.156,0.198 10 false - 0.323,2.198 0.979,2.427 0.656,0.229 10 false IND2 0.323,2.344 2.042,2.74 1.719,0.396 10 false Outer Mirror LH (Outer Rear View Mirror Indicator LH) 0.479,3.385 2.813,3.781 2.333,0.396 10 false Outer Mirror Retractor LH 2.885,1.344 3.354,1.542 0.469,0.198 10 false z29 2.948,1.156 3.417,1.354 0.469,0.198 10 false 8 3.281,1.354 3.75,1.552 0.469,0.198 10 false BSL 3.135,3.396 4.646,4.042 1.51,0.646 10 false Front Multiplex Network Door ECU LH 4.031,1.375 4.5,1.573 0.469,0.198 10 false BSMI 4.094,1.833 4.563,2.031 0.469,0.198 10 false GND 4.542,1.344 5.01,1.542 0.469,0.198 10 false E25 4.583,1.146 5.052,1.344 0.469,0.198 10 false 21 4.615,1.635 5.083,1.833 0.469,0.198 10 false 1 5.969,1.375 6.438,1.573 0.469,0.198 10 false OMIL 5.781,1.25 6.25,1.448 0.469,0.198 10 false 4 5.885,3.396 6.354,3.594 0.469,0.198 10 false G60 5.885,3.552 7.115,4.177 1.229,0.625 10 false Blind Spot Monitor Sensor LH 2.917,1.625 3.188,1.792 0.271,0.167 10 false 12 3.302,1.802 3.542,1.969 0.24,0.167 10 false - 2.875,1.823 3.344,2.021 0.469,0.198 10 false z29 4.542,1.823 5.01,2.021 0.469,0.198 10 false E25

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Result Proceed to
C1AB1 is not output A
C1AB1 is output B



A

B

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

Pre-procedure1

a.

Disconnect the blind spot monitor sensor LH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G60)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G60-4 (OMIL) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

Pre-procedure1

a.

Disconnect the G60 blind spot monitor sensor LH connector.


b.

Disconnect the IND2 outer mirror LH (outer rear view mirror indicator LH) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G60)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G60-4 (OMIL) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

Pre-procedure1

a.

Disconnect the G60 blind spot monitor sensor LH connector.


b.

Disconnect the z29 outer rear view mirror assembly LH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G60)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G60-4 (OMIL) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE OUTER MIRROR RETRACTOR LH

NG

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

Pre-procedure1

a.

Disconnect the G60 blind spot monitor sensor LH connector.


b.

Disconnect the E25 front multiplex network door ECU LH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G60)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G60-4 (OMIL) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR