| *1 | CABLE SUPPORT BRACKET | *2 | PARKING BRAKE SHOE HOLD DOWN SPRING CUP |
| *3 | PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING | *4 | PARKING BRAKE SHOE HOLD DOWN SPRING PIN |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
High temperature grease | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1.APPLY HIGH TEMPERATURE GREASE
46505
2.INSTALL PARKING BRAKE ANCHOR BLOCK SUB-ASSEMBLY
42450B
3.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH
4.CONNECT PARKING BRAKE CABLE
46602
5.INSTALL PARKING BRAKE SHOE LEVER SUB-ASSEMBLY LH
| *A | for LH Side | *B | for RH Side |
| *1 | Parking Brake Anchor Block Sub-assembly | - | - |
| *a | Pin | - | - |
|
High Temperature Grease | - | - |
Connect the parking brake cable to the parking brake shoe lever sub-assembly LH.
Apply high temperature grease to the areas of the parking brake anchor block sub-assembly which make contact with the parking brake shoe lever sub-assembly LH.
Check that the parking brake shoe lever sub-assembly is installed so that the pin is positioned as shown in the illustration.
| *1 | Parking Brake Shoe Lever Sub-assembly LH | - | - |
| *a | Parking Brake Inner Cable | - | - |
|
Top of Vehicle | - | - |
Check that the parking brake inner cable and parking brake shoe lever sub-assembly LH are securely connected by trying to pull them apart.
46580
6.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH
Using SST, install the No. 1 parking brake shoe assembly LH with the parking brake shoe hold down spring cup, parking brake shoe hold down compression spring and parking brake shoe hold down spring pin.
46590
7.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH
Using SST, install the No. 2 parking brake shoe assembly LH with the parking brake shoe hold down spring cup, parking brake shoe hold down compression spring and parking brake shoe hold down spring pin.
47406A
8.INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET
|
High Temperature Grease | - | - |
Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.
Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly LH and No. 2 parking brake shoe assembly LH.
Because the left and right parking brake shoe adjusting screw set are not interchangeable, verify the part number when installing the parking brake shoe adjusting screw set.
46550E
9.INSTALL NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING
Using SST, install the parking brake shoe return tension spring.
46550A
10.INSTALL NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING
Using SST, install the parking brake shoe return tension spring.
11. CHECK PARKING BRAKE INSTALLATION
| *A | for LH Side | *B | for RH Side |
|
Front of the Vehicle | - | - |
Check that each part is installed properly.
There should be no oil or grease on the friction surfaces of the shoe linings or discs.
47491A
13.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
15.ADJUST PARKING BRAKE
16.INSTALL REAR WHEEL
17. CHECK PARKING BRAKE CABLE INSTALLATION
| *a | Drive Shaft | *b | Shaft Boot |
| *c | Parking Brake Cable | - | - |
With the vehicle on the ground, check that the gap between the parking brake cable and drive shaft, and the gap between the parking brake cable and shaft boot are 10 mm (0.394 in.) or more.
Make sure that the cable is not twisted.
19. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
20.PERFORM PARKING BRAKE SHOE BEDDING