Home › Suspension › REAR SUSPENSION › REAR LOWER ARM
RM37H0E _53 Suspension _097406 REAR SUSPENSION _0455875 REAR LOWER ARM A

REAR SUSPENSION  REAR LOWER ARM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C447174N03
3.833,0.833 3.833,0.25 3.833,0.25 4,0.25 true 5.833,2 5.833,1.25 5.833,1.25 6,1.25 true 1.167,1.25 1.167,0.5 1.167,0.5 1.333,0.5 true 5.188,3.615 5.188,3.198 5.188,3.198 5.354,3.198 true 4.167,1.833 4.167,1.417 4.167,1.417 4.333,1.417 true 3.313,1.667 3.479,1.667 3.479,1.667 3.479,1.5 true 5.5,2.792 5.333,2.792 5.333,2.792 5.333,2.625 true 0.969,2.417 1.281,2.615 0.313,0.198 10 false x 2 4.156,4.354 4.469,4.552 0.313,0.198 10 false x 2 5.406,2.458 5.719,2.656 0.313,0.198 10 false x 2 3.594,1.333 3.906,1.531 0.313,0.198 10 false x 2 4.125,3.313 4.438,3.51 0.313,0.198 10 false x 2 3.813,3.521 4.125,3.719 0.313,0.198 10 false x 4 5.406,3.021 5.688,3.375 0.281,0.354 18 false 1 1.406,0.385 1.688,0.74 0.281,0.354 18 false 2 4.406,1.26 4.688,1.615 0.281,0.354 18 false 3 6.063,1.115 6.344,1.469 0.281,0.354 18 false 4 4.073,0.083 4.354,0.438 0.281,0.354 18 false 5 5.563,2.698 5.906,2.896 0.344,0.198 10 false ●★ 2.99,1.573 3.333,1.771 0.344,0.198 10 false ●★

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 2 DIFFERENTIAL SUPPORT PROTECTOR 52384C - - -
2 NO. 1 DIFFERENTIAL SUPPORT PROTECTOR 52383E - - -
3 REAR SUSPENSION BRACE COVER 53661B - - -
4 REAR SUSPENSION MEMBER BRACE LH 52296 - - -
5 REAR SUSPENSION MEMBER BRACE RH 52295 - - -

★ Precoated part ● Non-reusable part

C448159N03
6.073,3.656 6.073,3.073 6.073,3.073 6.24,3.073 true 4.25,2.417 4.25,2.083 4.25,2.083 4.417,2.083 true 2.208,2.813 2.708,2.813 true 4.417,0.5 4.917,0.5 true 5.188,1.583 5.188,1.25 5.188,1.25 5.354,1.25 true 2.469,5.229 2.844,5.229 2.844,5.229 2.844,4.917 true 3.313,3.25 3.677,3.25 3.677,3.25 3.677,2.917 true 3.729,4.792 4.229,4.792 true 4.479,1.99 4.802,2.188 0.323,0.198 10 false *1 1.99,2.719 2.219,2.927 0.229,0.208 10 false *2 5.458,1.094 6.01,1.448 0.552,0.354 18 false 9 6.354,2.927 6.906,3.281 0.552,0.354 18 false 6 2.156,5.063 2.438,5.385 0.281,0.323 18 false 7 2.958,3.115 3.302,3.417 0.344,0.302 18 false 10 4.99,0.344 5.542,0.698 0.552,0.354 18 false 8 4.292,4.688 4.5,4.875 0.208,0.188 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

6 DISCONNECT LOWER NO. 2 SUSPENSION ARM ASSEMBLY LH - - - -
7 REMOVE LOWER NO. 2 SUSPENSION ARM ASSEMBLY LH 48730 (Click here) - -
8 TIE ROD ASSEMBLY LH 48840A - - -
9 DISCONNECT STEERING KNUCKLE LH 89408C - - -
10 REAR NO. 2 SUSPENSION ARM ASSEMBLY LH 48740F (Click here) - -

*1 REAR SUSPENSION ARM ATTACHMENT SUB-ASSEMBLY *2 REAR NO. 2 SUSPENSION TOE ADJUST PLATE
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear lower arm removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)
Wheel alignment adjustment Perform "Calibration" Electronically controlled brake system malfunctions (Click here)


HINT:
·

Use the same procedure for the RH and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 52384C 1.REMOVE NO. 2 DIFFERENTIAL SUPPORT PROTECTOR

Hide 52383E 2.REMOVE NO. 1 DIFFERENTIAL SUPPORT PROTECTOR

Hide 53661B 3.REMOVE REAR SUSPENSION BRACE COVER

Hide 52296 4.REMOVE REAR SUSPENSION MEMBER BRACE LH

Hide 52295 5.REMOVE REAR SUSPENSION MEMBER BRACE RH

a.

Use the same procedure as for the LH side.


Hide 6.REMOVE REAR TIRE

Hide 48730 7.REMOVE LOWER CONTROL ARM ASSEMBLY LH

a.
C446781C01
6.146,2.771 6.417,2.417 6.417,2.417 6.583,2.417 true 2.583,3.26 2.917,3.26 true 5.021,2.927 4.75,2.5 4.75,2.5 4.583,2.5 true 5.094,3.188 4.948,3.438 4.948,3.438 5.135,3.26 true 5.573,2.698 5.417,2.25 5.417,2.25 5.25,2.25 true 1.635,2.948 1.969,2.948 true 6,3.385 6.083,3.5 6.083,3.5 6.167,3.5 true 4.833,3.448 5.063,3.615 0.229,0.167 10 false *a 4.458,3.083 4.75,3.333 0.292,0.25 10 false *b 4.406,2.438 4.667,2.667 0.26,0.229 10 false *c 5.073,2.188 5.323,2.438 0.25,0.25 10 false *d 6.427,3.031 6.677,3.281 0.25,0.25 10 false *g 6.219,3.427 6.448,3.594 0.229,0.167 10 false *e 6.646,2.354 6.896,2.604 0.25,0.25 10 false *f 3.01,3.198 3.354,3.385 0.344,0.188 10 true SST 1.344,2.865 1.604,3.063 0.26,0.198 10 true *h 1.979,0.104 2.313,0.396 0.333,0.292 18 false i 0.49,2.031 0.927,2.323 0.438,0.292 18 true ii, iii
*a SST (Spacer B) *b 1 mm (0.0394 in.)
*c Spacer *d Center Nut
*e Body *f Claw
*g Parallel *h String


i.

Remove the nut.


ii.

Install 2 SST (spacer B) onto the lower control arm assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

SST
09960-20010  (09961-02060)

NOTICE:
·

Make sure to install the spacers (SST spacer A) as the rear axle carrier sub-assembly LH spacer may shift.

·

As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.




iii.

Using SST, disconnect the lower control arm assembly LH from the rear axle carrier sub-assembly LH.

SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and end of the SST bolt.

·

Do not damage the dust cover.

·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.





b.
C447178C01
2.531,0.104 2.813,0.458 0.281,0.354 18 true i
V100135

Bolt
V100136

Nut


i.

Remove the bolt, nut and lower control arm assembly LH.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.




Hide 48840A 8.DISCONNECT REAR STABILIZER LINK ASSEMBLY LH

a.
C447179


Hide 89408C 9.DISCONNECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

a.
C447180


Hide 48740F 10.DISCONNECT REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.
C447181C01
5.167,0.333 5.333,0.167 5.333,0.167 5.5,0.167 true 4.583,1 4.75,1 true 5.5,0.75 5.583,1 5.583,1 5.75,1 true 4.854,3.229 5.021,3.479 5.021,3.479 5.188,3.479 true 0.229,0.146 0.51,0.5 0.281,0.354 18 true i 4.031,0.094 4.26,0.458 0.229,0.365 18 true ii 5.219,3.417 5.531,3.573 0.313,0.156 10 true *a 5.531,0.115 5.844,0.271 0.313,0.156 10 false *b 5.802,0.938 6.115,1.094 0.313,0.156 10 false *c 4.344,0.917 4.583,1.083 0.24,0.167 10 false *d
*a A *b Arm
*c Slide Pin *d Axle Carrier
V100135

Front of the Vehicle - -


i.

Loosen the nut.


ii.

Using a plastic-faced hammer or equivalent, strike the part labeled A from the rear of the vehicle to maintain the clearance at the slide pin area.

NOTICE:

Be careful not to damage the arm.



iii.

Remove the nut, bolt and washer.



b.
C447182