Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457023 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2650  Slide Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly LH (for LHD) or RH (for RHD) does not receive a slide motor position sensor signal despite the seat having been moved forward or backward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2650 Slide Sensor Malfunction Slide motor position sensor signal not received when power seat moved forward or backward.
·

Position control ECU assembly LH (for LHD)

·

Position control ECU assembly RH (for RHD)

·

Slide motor (front seat adjuster assembly LH) (for LHD)

·

Slide motor (front seat adjuster assembly RH) (for RHD)

·

Harness or connector


Driver Seat A

WIRING DIAGRAM

for LHD:


E395539E16
4.802,0.552 5.156,0.781 0.354,0.229 10 false L41 4.823,1.073 5.135,1.271 0.313,0.198 10 false L41 4.813,1.583 5.125,1.781 0.313,0.198 10 false L43 4.802,2.094 5.177,2.365 0.375,0.271 10 false L43 2.208,0.49 2.365,0.688 0.156,0.198 10 false 4 2.208,0.99 2.365,1.188 0.156,0.198 10 false 1 2.219,1.479 2.406,1.698 0.188,0.219 10 false 2 2.219,1.99 2.458,2.281 0.24,0.292 10 false 3 4.865,0.333 5.021,0.531 0.156,0.198 10 false 1 4.896,0.844 5.115,1.094 0.219,0.25 10 false 5 4.854,1.354 5.125,1.583 0.271,0.229 10 false 26 4.844,1.865 5.042,2.073 0.198,0.208 10 false 12 1.406,2.49 1.813,2.823 0.406,0.333 10 false L26 5.135,2.583 6.469,3.333 1.333,0.75 10 false Position Control ECU Assembly LH 1.385,2.677 2.917,2.875 1.531,0.198 10 false Slide Motor LH 0.542,3.094 3.031,3.354 2.49,0.26 10 false Front Seat Adjuster Assembly LH 5.24,0.573 5.854,0.771 0.615,0.198 10 false SLD+ 5.24,1.104 5.854,1.302 0.615,0.198 10 false SLD- 5.24,1.615 5.854,1.813 0.615,0.198 10 false SSRS 5.24,2.125 5.854,2.323 0.615,0.198 10 false SGND


for RHD:


E395539E15
4.823,0.573 5.135,0.771 0.313,0.198 10 false L15 4.844,1.094 5.156,1.292 0.313,0.198 10 false L15 4.813,1.604 5.125,1.802 0.313,0.198 10 false L17 4.823,2.115 5.135,2.313 0.313,0.198 10 false L17 2.208,0.49 2.365,0.688 0.156,0.198 10 false 4 2.208,0.99 2.365,1.188 0.156,0.198 10 false 1 2.219,1.521 2.375,1.719 0.156,0.198 10 false 2 2.219,2.031 2.375,2.229 0.156,0.198 10 false 3 4.885,0.344 5.042,0.542 0.156,0.198 10 false 1 4.896,0.865 5.052,1.063 0.156,0.198 10 false 5 4.854,1.375 5.052,1.573 0.198,0.198 10 false 26 4.854,1.885 5.052,2.094 0.198,0.208 10 false 12 1.396,2.521 1.708,2.719 0.313,0.198 10 false L1 5.031,2.615 6.365,3.125 1.333,0.51 10 false Position Control ECU Assembly RH 1.365,2.698 2.896,2.896 1.531,0.198 10 false Slide Motor RH 0.521,3.063 3.125,3.521 2.604,0.458 10 false Front Seat Adjuster Assembly RH 5.24,0.573 5.854,0.771 0.615,0.198 10 false SLD+ 5.24,1.104 5.854,1.302 0.615,0.198 10 false SLD- 5.24,1.615 5.854,1.813 0.615,0.198 10 false SSRS 5.24,2.125 5.854,2.323 0.615,0.198 10 false SGND


CAUTION / NOTICE / HINT

*1: for LHD

*2: for RHD


NOTICE:

Initializing the position control ECU assembly LH*1 or RH*2 will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly LH*1 or RH*2 after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CLEAR DTC

B

9.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2650 is not output A
B2650 is output B



A

B

4.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
4.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
OK:

Slide motor operates normally.



Result:
Proceed to
OK
NG



OK

5.CHECK POSITION CONTROL ECU ASSEMBLY LH (SLIDE MOTOR CIRCUIT)

NG

7.INSPECT FRONT SEAT ADJUSTER ASSEMBLY LH (SLIDE MOTOR)
5.CHECK POSITION CONTROL ECU ASSEMBLY LH (SLIDE MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L26 slide motor (front seat adjuster assembly LH) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L26)Location & Routing

Click Connector(L26)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Slide Position Motor LH (Front Seat Adjuster Assembly LH)

L26-2 - L26-3 Slide switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH

NG

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY LH])
6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY LH])

Pre-procedure1

a.

Disconnect the L43 position control ECU assembly LH connector.


b.

Disconnect the L26 slide motor (front seat adjuster assembly LH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L43,L26)Location & Routing

Click Connector(L43)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L26)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Slide Position Motor LH (Front Seat Adjuster Assembly LH)

L43-26 (SSRS) - L26-2 Always Below 1 Ω
L43-26 (SSRS) or L26-2 - Body ground Always 10 kΩ or higher
L43-12 (SGND) - L26-3 Always Below 1 Ω
L43-12 (SGND) or L26-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT SEAT ADJUSTER ASSEMBLY LH (SLIDE MOTOR)

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>INSPECTION

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY LH])

NG

REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY LH])

Pre-procedure1

a.

Disconnect the L41 position control ECU assembly LH connector.


b.

Disconnect the L26 slide motor (front seat adjuster assembly LH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L41,L26)Location & Routing

Click Connector(L41)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L26)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Slide Position Motor LH (Front Seat Adjuster Assembly LH)

L41-1 (SLD+) - L26-4 Always Below 1 Ω
L41-1 (SLD+) or L26-4 - Body ground Always 10 kΩ or higher
L41-5 (SLD-) - L26-1 Always Below 1 Ω
L41-5 (SLD-) or L26-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2650 is not output A
B2650 is output B



A

B

11.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
11.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
OK:

Slide motor operates normally.



Result:
Proceed to
OK
NG



OK

12.CHECK POSITION CONTROL ECU ASSEMBLY RH (SLIDE MOTOR CIRCUIT)

NG

14.INSPECT FRONT SEAT ADJUSTER ASSEMBLY RH (SLIDE MOTOR)
12.CHECK POSITION CONTROL ECU ASSEMBLY RH (SLIDE MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L1 slide motor (front seat adjuster assembly RH) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L1)Location & Routing

Click Connector(L1)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Slide Position Motor RH (Front Seat Adjuster Assembly RH)

L1-2 - L1-3 Slide switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

NG

13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - FRONT SEAT ADJUSTER ASSEMBLY RH)
13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - FRONT SEAT ADJUSTER ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the L17 position control ECU assembly RH connector.


b.

Disconnect the L1 slide motor (front seat adjuster assembly RH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L17,L1)Location & Routing

Click Connector(L17)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L1)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Slide Position Motor RH (Front Seat Adjuster Assembly RH)

L17-26 (SSRS) - L1-2 Always Below 1 Ω
L17-26 (SSRS) or L1-2 - Other Body ground Always 10 kΩ or higher
L17-12 (SGND) - L1-3 Always Below 1 Ω
L17-12 (SGND) or L1-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT FRONT SEAT ADJUSTER ASSEMBLY RH (SLIDE MOTOR)

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>INSPECTION

Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY RH])

NG

REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY RH])

Pre-procedure1

a.

Disconnect the L15 position control ECU assembly RH connector.


b.

Disconnect the L1 slide motor (front seat adjuster assembly RH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L15,L1)Location & Routing

Click Connector(L15)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L1)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Slide Position Motor RH (Front Seat Adjuster Assembly RH)

L15-1 (SLD+) - L1-4 Always Below 1 Ω
L15-1 (SLD+) or L1-4 - Body ground Always 10 kΩ or higher
L15-5 (SLD-) - L1-1 Always Below 1 Ω
L15-5 (SLD-) or L1-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR