Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457023 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly LH (for LHD) or RH (for RHD) does not receive a reclining motor position sensor signal despite the seat having been moved forward or rearward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2651 Reclining Sensor Malfunction Reclining motor position sensor signal not received when power seat moved forward or rearward.
·

Position control ECU assembly LH (for LHD)

·

Position control ECU assembly RH (for RHD)

·

Reclining motor (front seatback frame sub-assembly LH) (for LHD)

·

Reclining motor (front seatback frame sub-assembly RH) (for RHD)

·

Harness or connector


Driver Seat A

WIRING DIAGRAM

for LHD:


E395539E17
4.813,0.552 5.177,0.771 0.365,0.219 10 false L41 4.802,1.073 5.115,1.271 0.313,0.198 10 false L42 4.813,1.573 5.156,1.813 0.344,0.24 10 false L43 4.823,2.083 5.135,2.281 0.313,0.198 10 false L43 2.198,0.479 2.375,0.719 0.177,0.24 10 false 1 2.208,0.99 2.406,1.25 0.198,0.26 10 false 4 2.198,1.49 2.469,1.76 0.271,0.271 10 false 2 2.208,1.99 2.458,2.26 0.25,0.271 10 false 3 4.844,0.302 5.073,0.51 0.229,0.208 10 false 10 4.885,0.844 5.094,1.073 0.208,0.229 10 false 6 4.854,1.354 5.125,1.573 0.271,0.219 10 false 11 4.854,1.885 5.052,2.094 0.198,0.208 10 false 12 1.375,2.51 1.688,2.708 0.313,0.198 10 false L55 5.104,2.604 6.448,3.063 1.344,0.458 10 false Position Control ECU Assembly LH 1.344,2.688 2.948,3.01 1.604,0.323 10 false Reclining Motor LH 0.573,3.094 3.427,3.479 2.854,0.385 10 false Front Seatback Frame Sub-assembly LH 5.24,0.573 5.854,0.771 0.615,0.198 10 false RCL+ 5.24,1.104 5.854,1.302 0.615,0.198 10 false RCL- 5.24,1.615 5.854,1.813 0.615,0.198 10 false SSRR 5.24,2.125 5.854,2.323 0.615,0.198 10 false SGND


for RHD:


E395539E18
4.823,0.542 5.135,0.74 0.313,0.198 10 false L15 4.823,1.063 5.135,1.26 0.313,0.198 10 false L16 4.813,1.604 5.125,1.802 0.313,0.198 10 false L17 4.823,2.115 5.135,2.313 0.313,0.198 10 false L17 2.198,0.469 2.385,0.698 0.188,0.229 10 false 4 2.208,0.99 2.406,1.208 0.198,0.219 10 false 1 2.219,1.49 2.396,1.708 0.177,0.219 10 false 2 2.219,1.99 2.427,2.229 0.208,0.24 10 false 3 4.844,0.313 5.104,0.573 0.26,0.26 10 false 10 4.885,0.844 5.115,1.094 0.229,0.25 10 false 6 4.844,1.354 5.042,1.552 0.198,0.198 10 false 11 4.854,1.885 5.052,2.094 0.198,0.208 10 false 12 1.385,2.49 1.792,2.708 0.406,0.219 10 false L49 5.031,2.615 6.365,3.125 1.333,0.51 10 false Position Control ECU Assembly RH 1.365,2.677 2.896,2.875 1.531,0.198 10 false Reclining Motor RH 0.521,3.063 3.135,3.646 2.615,0.583 10 false Front Seatback Frame Sub-assembly RH 5.24,0.573 5.854,0.771 0.615,0.198 10 false SLD+ 5.24,1.104 5.854,1.302 0.615,0.198 10 false SLD- 5.24,1.615 5.854,1.813 0.615,0.198 10 false SSRS 5.24,2.125 5.854,2.323 0.615,0.198 10 false SGND


CAUTION / NOTICE / HINT

*1: for LHD

*2: for RHD


NOTICE:

Initializing the position control ECU assembly LH*1 or RH*2 will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly LH*1 or RH*2 after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CLEAR DTC

B

9.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2651 is not output A
B2651 is output B



A

B

4.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING)
4.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
OK:

Reclining motor operates normally.



Result:
Proceed to
OK
NG



OK

5.CHECK POSITION CONTROL ECU ASSEMBLY LH (RECLINING MOTOR CIRCUIT)

NG

7.INSPECT FRONT SEAT BACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)
5.CHECK POSITION CONTROL ECU ASSEMBLY LH (RECLINING MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L55 reclining motor (front seatback frame sub-assembly LH) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L55)Location & Routing

Click Connector(L55)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Reclining Position Motor LH (Front Seat Adjuster Assembly LH)

L55-2 - L55-3 Reclining switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT SEAT BACK FRAME SUB-ASSEMBLY LH

NG

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY LH])
6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY LH])

Pre-procedure1

a.

Disconnect the L43 position control ECU assembly LH connector.


b.

Disconnect the L55 reclining motor (front seatback frame sub-assembly LH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L43,L55)Location & Routing

Click Connector(L43)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L55)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Reclining Position Motor LH (Front Seat Adjuster Assembly LH)

L43-11 (SSRR) - L55-2 Always Below 1 Ω
L43-11 (SSRR) or L55-2 - Body ground Always 10 kΩ or higher
L43-12 (SGND) - L55-3 Always Below 1 Ω
L43-12 (SGND) or L55-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT SEAT BACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>INSPECTION

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY LH])

NG

REPLACE FRONT SEAT BACK FRAME SUB-ASSEMBLY LH

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY LH])

Pre-procedure1

a.

Disconnect the L41 and L42 position control ECU assembly LH connectors.


b.

Disconnect the L55 reclining motor (front seatback frame sub-assembly LH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L41,L55,L42)Location & Routing

Click Connector(L41)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L55)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Reclining Position Motor LH (Front Seat Adjuster Assembly LH)

Click Connector(L42)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

L41-10 (RCL+) - L55-1 Always Below 1 Ω
L41-10 (RCL+) or L55-1 - Other terminals and body ground Always 10 kΩ or higher
L42-6 (RCL-) - L55-4 Always Below 1 Ω
L42-6 (RCL-) or L55-4 - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2651 is not output A
B2651 is output B



A

B

11.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING)
11.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
OK:

Reclining motor operates normally.



Result:
Proceed to
OK
NG



OK

12.CHECK POSITION CONTROL ECU ASSEMBLY RH (RECLINING MOTOR CIRCUIT)

NG

14.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY RH (RECLINING MOTOR)
12.CHECK POSITION CONTROL ECU ASSEMBLY RH (RECLINING MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L49 reclining motor (front seatback frame sub-assembly RH) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L49)Location & Routing

Click Connector(L49)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Reclining Position Motor RH (Front Seat Adjuster Assembly RH)

L49-2 - L49-3 Reclining switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY RH

NG

13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY RH])
13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY RH])

Pre-procedure1

a.

Disconnect the L17 position control ECU assembly RH connector.


b.

Disconnect the L49 reclining motor (front seatback frame sub-assembly RH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L17,L49)Location & Routing

Click Connector(L17)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L49)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Reclining Position Motor RH (Front Seat Adjuster Assembly RH)

L17-11 (SSRR) - L49-2 Always Below 1 Ω
L17-11 (SSRR) or L49-2 - Other terminals and body ground Always 10 kΩ or higher
L17-12 (SGND) - L49-3 Always Below 1 Ω
L17-12 (SGND) or L49-3 - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY RH (RECLINING MOTOR)

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>INSPECTION

Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY RH])

NG

REPLACE FRONT SEAT BACK FRAME SUB-ASSEMBLY RH

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY RH])

Pre-procedure1

a.

Disconnect the L15 and L16 position control ECU assembly RH connectors.


b.

Disconnect the L49 reclining motor (front seatback frame sub-assembly RH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L15,L49,L16)Location & Routing

Click Connector(L15)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L49)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Reclining Position Motor RH (Front Seat Adjuster Assembly RH)

Click Connector(L16)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

L15-10 (RCL+) - L49-1 Always Below 1 Ω
L15-10 (RCL+) or L49-1 - Body ground Always 10 kΩ or higher
L16-6 (RCL-) - L49-4 Always Below 1 Ω
L16-6 (RCL-) or L49-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR