Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457023 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2658  Short in Sensor with Motor Power Supply Circuit  


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2658 Short in Sensor with Motor Power Supply Circuit Problem with the voltage supplied to the position control sensor.
·

Position control ECU assembly LH (for LHD)

·

Position control ECU assembly RH (for RHD)

·

Slide motor (front seat adjuster assembly LH) (for LHD)

·

Slide motor (front seat adjuster assembly RH) (for RHD)

·

Power seat tilt motor assembly LH (for LHD)

·

Power seat tilt motor assembly RH (for RHD)

·

Power seat lifter motor assembly LH (for LHD)

·

Power seat lifter motor assembly RH (for RHD)

·

Reclining motor (front seatback frame sub-assembly LH) (for LHD)

·

Reclining motor (front seatback frame sub-assembly RH) (for RHD)

·

Harness or connector


Driver Seat A

WIRING DIAGRAM

E407951E06
2.083,1.229 3.073,1.5 0.99,0.271 10 false Slide Motor 2.927,0.552 3.5,0.833 0.573,0.281 10 false 2 1.948,0.563 2.521,0.844 0.573,0.281 10 false 3 1.021,2.771 4.781,3.156 3.76,0.385 10 false Power Seat Tilt Motor Assembly LH (Front Vertical Motor)*1, Power Seat Tilt Motor Assembly RH (Front Vertical Motor)*2 1.302,4.031 3.948,4.396 2.646,0.365 10 false Power Seat Lifter Motor Assembly LH*1, Power Seat Lifter Motor Assembly RH*2 0.969,6.021 3.75,6.396 2.781,0.375 10 false Front Seatback Frame Sub-assembly LH*1, Front Seatback Frame Sub-assembly RH*2 2.01,5.615 3.042,5.792 1.031,0.177 10 false Reclining Motor 5.229,6.583 5.802,6.865 0.573,0.281 10 false SGND 5.24,5.042 5.813,5.323 0.573,0.281 10 false SSRR 5.229,3.573 5.698,3.76 0.469,0.188 10 false SSRL 5.229,2.365 5.792,2.573 0.563,0.208 10 false SSFV 5.24,0.667 5.813,0.948 0.573,0.281 10 false SSRS 4.906,0.552 5.479,0.833 0.573,0.281 10 false 26 4.938,2.24 5.188,2.427 0.25,0.188 10 false 10 4.948,3.448 5.146,3.635 0.198,0.188 10 false 25 4.927,4.927 5.5,5.208 0.573,0.281 10 false 11 4.938,6.469 5.51,6.75 0.573,0.281 10 false 12 4.448,7.104 6.854,7.656 2.406,0.552 10 false Position Control ECU Assembly LH*1, Position Control ECU Assembly RH*2 1.917,2.24 2.052,2.406 0.135,0.167 10 false 3 1.917,3.469 2.042,3.646 0.125,0.177 10 false 3 1.958,4.948 2.531,5.229 0.573,0.281 10 false 3 2.906,2.24 3.094,2.427 0.188,0.188 10 false 2 2.917,3.448 3.063,3.625 0.146,0.177 10 false 2 2.958,4.927 3.531,5.208 0.573,0.281 10 false 2 2.083,1.083 2.958,1.396 0.875,0.313 10 false L26*1, L1*2 1.063,2.615 1.875,2.792 0.813,0.177 10 false L27*1, L2*2 1.281,3.865 2.177,4.052 0.896,0.188 10 false L28*1, L3*2 2.031,5.458 3.021,5.719 0.99,0.26 10 false L55*1, L49*2 4.417,6.927 5.615,7.198 1.198,0.271 10 false L43*1, L17*2 0.698,7.427 2.385,7.625 1.688,0.198 10 false *1: for LHD 1.896,7.427 3.583,7.625 1.688,0.198 10 false *2: for RHD 1.177,1.563 3.615,1.917 2.438,0.354 10 false Front Seat Adjuster Assembly LH*1, Front Seat Adjuster Assembly RH*2

CAUTION / NOTICE / HINT

*1: for LHD

*2: for RHD


NOTICE:

Initializing the position control ECU assembly LH*1 or RH*2 will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly LH*1 or RH*2 after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CLEAR DTC

B

16.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2658 is not output A
B2658 is output B



A

B

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY LH])
4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY LH])

Pre-procedure1

a.

Disconnect the L43 position control ECU assembly LH connector.


b.

Disconnect the L26 slide motor (front seat adjuster assembly LH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L43,L26)Location & Routing

Click Connector(L43)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L26)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Slide Position Motor LH (Front Seat Adjuster Assembly LH)

L43-26 (SSRS) - L26-2 Always Below 1 Ω
L43-26 (SSRS) or L26-2 - Body ground Always 10 kΩ or higher
L43-12 (SGND) - L26-3 Always Below 1 Ω
L43-12 (SGND) or L26-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK POSITION CONTROL ECU ASSEMBLY LH (SLIDE MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POSITION CONTROL ECU ASSEMBLY LH (SLIDE MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L26 slide motor (front seat adjuster assembly LH) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L26)Location & Routing

Click Connector(L26)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Slide Position Motor LH (Front Seat Adjuster Assembly LH)

L26-2 - L26-3 Slide switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - POWER SEAT TILT MOTOR ASSEMBLY LH)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - POWER SEAT TILT MOTOR ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the L43 position control ECU assembly LH connector.


b.

Disconnect the L27 power seat tilt motor assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L43,L27)Location & Routing

Click Connector(L43)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L27)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Tilt Position Motor LH (Front Seat Adjuster Assembly LH)

L43-10 (SSFV) - L27-2 Always Below 1 Ω
L43-10 (SSFV) or L27-2 - Body ground Always 10 kΩ or higher
L43-12 (SGND) - L27-3 Always Below 1 Ω
L43-12 (SGND) or L27-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.CHECK POSITION CONTROL ECU ASSEMBLY LH (FRONT VERTICAL MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK POSITION CONTROL ECU ASSEMBLY LH (FRONT VERTICAL MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L27 power seat tilt motor assembly LH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L27)Location & Routing

Click Connector(L27)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Tilt Position Motor LH (Front Seat Adjuster Assembly LH)

L27-2 - L27-3 Front vertical switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - POWER SEAT LIFTER MOTOR ASSEMBLY LH)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY LH

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - POWER SEAT LIFTER MOTOR ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the L43 position control ECU assembly LH connector.


b.

Disconnect the L28 power seat lifter motor assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L43,L28)Location & Routing

Click Connector(L43)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L28)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Lift Position Motor LH (Front Seat Adjuster Assembly LH)

L43-25 (SSRL) - L28-2 Always Below 1 Ω
L43-25 (SSRL) or L28-2 - Body ground Always 10 kΩ or higher
L43-12 (SGND) - L28-3 Always Below 1 Ω
L43-12 (SGND) or L28-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

9.CHECK POSITION CONTROL ECU ASSEMBLY LH (LIFTER MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK POSITION CONTROL ECU ASSEMBLY LH (LIFTER MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L28 power seat lifter motor assembly LH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L28)Location & Routing

Click Connector(L28)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Lift Position Motor LH (Front Seat Adjuster Assembly LH)

L28-2 - L28-3 Rear lifter switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

10.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY LH])

NG

REPLACE POSITION CONTROL ECU ASSEMBLY LH

10.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY LH])

Pre-procedure1

a.

Disconnect the L43 position control ECU assembly LH connector.


b.

Disconnect the L55 reclining motor (front seatback frame sub-assembly LH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L43,L55)Location & Routing

Click Connector(L43)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L55)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Reclining Position Motor LH (Front Seat Adjuster Assembly LH)

L43-11 (SSRR) - L55-2 Always Below 1 Ω
L43-11 (SSRR) or L55-2 - Body ground Always 10 kΩ or higher
L43-12 (SGND) - L55-3 Always Below 1 Ω
L43-12 (SGND) or L55-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

11.CHECK POSITION CONTROL ECU ASSEMBLY LH (RECLINING MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK POSITION CONTROL ECU ASSEMBLY LH (RECLINING MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L55 reclining motor (front seatback frame sub-assembly LH) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L55)Location & Routing

Click Connector(L55)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Reclining Position Motor LH (Front Seat Adjuster Assembly LH)

L55-2 - L55-3 Reclining switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

12.REPLACE FRONT VERTICAL MOTOR (POWER SEAT TILT MOTOR ASSEMBLY LH)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY LH

12.REPLACE FRONT VERTICAL MOTOR (POWER SEAT TILT MOTOR ASSEMBLY LH)

Pre-procedure1

a.

Replace the front vertical motor (power seat tilt motor assembly LH) with a new or known good one.

HINT:

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL



b.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Procedure1

a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
Result:
Result Proceed to
B2658 is not output A
B2658 is output B



Post-procedure1

a.

None



A

END (FRONT VERTICAL MOTOR [POWER SEAT TILT MOTOR ASSEMBLY LH] WAS DEFECTIVE)

B

13.REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY LH
13.REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY LH

Pre-procedure1

a.

Replace the power seat lifter motor assembly LH with a new or known good one.

HINT:

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL



b.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Procedure1

a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
Result:
Result Proceed to
B2658 is not output A
B2658 is output B



Post-procedure1

a.

None



A

END (POWER SEAT LIFTER MOTOR ASSEMBLY LH WAS DEFECTIVE)

B

14.REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)
14.REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

Pre-procedure1

a.

Replace the slide motor (front seat adjuster assembly LH) with a new or known good one.

HINT:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY



b.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Procedure1

a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
Result:
Result Proceed to
B2658 is not output A
B2658 is output B



Post-procedure1

a.

None



A

END (SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY LH])

B

15.REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
15.REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH)

Pre-procedure1

a.

Replace the reclining motor (front seatback frame sub-assembly LH) with a new or known good one.

HINT:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY



b.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Procedure1

a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
Result:
Result Proceed to
B2658 is not output A
B2658 is output B



Post-procedure1

a.

None



A

END (RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY LH] WAS DEFECTIVE)

B

REPLACE POSITION CONTROL ECU ASSEMBLY LH

16.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

17.CHECK FOR DTC
17.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2658 is not output A
B2658 is output B



A

B

18.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY RH])
18.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY RH])

Pre-procedure1

a.

Disconnect the L17 position control ECU assembly RH connector.


b.

Disconnect the L1 slide motor (front seat adjuster assembly RH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L17,L1)Location & Routing

Click Connector(L17)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L1)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Slide Position Motor RH (Front Seat Adjuster Assembly RH)

L17-26 (SSRS) - L1-2 Always Below 1 Ω
L17-26 (SSRS) or L1-2 - Body ground Always 10 kΩ or higher
L17-12 (SGND) - L1-3 Always Below 1 Ω
L17-12 (SGND) or L1-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

19.CHECK POSITION CONTROL ECU ASSEMBLY RH (SLIDE MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK POSITION CONTROL ECU ASSEMBLY RH (SLIDE MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L1 slide motor (front seat adjuster assembly RH) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L1)Location & Routing

Click Connector(L1)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Slide Position Motor RH (Front Seat Adjuster Assembly RH)

L1-2 - L1-3 Slide switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

20.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - POWER SEAT TILT MOTOR ASSEMBLY RH)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY RH

20.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - POWER SEAT TILT MOTOR ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the L17 position control ECU assembly RH connector.


b.

Disconnect the L2 power seat tilt motor assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L17,L2)Location & Routing

Click Connector(L17)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L2)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Tilt Position Motor RH (Front Seat Adjuster Assembly RH)

L17-10 (SSFV) - L2-2 Always Below 1 Ω
L17-10 (SSFV) or L2-2 - Body ground Always 10 kΩ or higher
L17-12 (SGND) - L2-3 Always Below 1 Ω
L17-12 (SGND) or L2-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

21.CHECK POSITION CONTROL ECU ASSEMBLY RH (FRONT VERTICAL MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK POSITION CONTROL ECU ASSEMBLY RH (FRONT VERTICAL MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L2 power seat tilt motor assembly RH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L2)Location & Routing

Click Connector(L2)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Tilt Position Motor RH (Front Seat Adjuster Assembly RH)

L2-2 - L2-3 Front vertical switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

22.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - POWER SEAT LIFTER MOTOR ASSEMBLY RH)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY RH

22.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - POWER SEAT LIFTER MOTOR ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the L17 position control ECU assembly RH connector.


b.

Disconnect the L3 power seat lifter motor assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L17,L3)Location & Routing

Click Connector(L17)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L3)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Lift Position Motor RH (Front Seat Adjuster Assembly RH)

L17-25 (SSRL) - L3-2 Always Below 1 Ω
L17-25 (SSRL) or L3-2 - Body ground Always 10 kΩ or higher
L17-12 (SGND) - L3-3 Always Below 1 Ω
L17-12 (SGND) or L3-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

23.CHECK POSITION CONTROL ECU ASSEMBLY RH (LIFTER MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK POSITION CONTROL ECU ASSEMBLY RH (LIFTER MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L3 power seat lifter motor assembly RH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L3)Location & Routing

Click Connector(L3)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Lift Position Motor RH (Front Seat Adjuster Assembly RH)

L3-2 - L3-3 Rear lifter switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

24.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY RH])

NG

REPLACE POSITION CONTROL ECU ASSEMBLY RH

24.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY RH])

Pre-procedure1

a.

Disconnect the L17 position control ECU assembly RH connector.


b.

Disconnect the L49 reclining motor (front seatback frame sub-assembly RH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L17,L49)Location & Routing

Click Connector(L17)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L49)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Reclining Position Motor RH (Front Seat Adjuster Assembly RH)

L17-11 (SSRR) - L49-2 Always Below 1 Ω
L17-11 (SSRR) or L49-2 - Body ground Always 10 kΩ or higher
L17-12 (SGND) - L49-3 Always Below 1 Ω
L17-12 (SGND) or L49-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

25.CHECK POSITION CONTROL ECU ASSEMBLY RH (RECLINING MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK POSITION CONTROL ECU ASSEMBLY RH (RECLINING MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L49 reclining motor (front seatback frame sub-assembly RH) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L49)Location & Routing

Click Connector(L49)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Reclining Position Motor RH (Front Seat Adjuster Assembly RH)

L49-2 - L49-3 Reclining switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

26.REPLACE FRONT VERTICAL MOTOR (POWER SEAT TILT MOTOR ASSEMBLY RH)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY RH

26.REPLACE FRONT VERTICAL MOTOR (POWER SEAT TILT MOTOR ASSEMBLY RH)

Pre-procedure1

a.

Replace the front vertical motor (power seat tilt motor assembly RH) with a new or known good one.

HINT:

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL



b.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Procedure1

a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
Result:
Result Proceed to
B2658 is not output A
B2658 is output B



Post-procedure1

a.

None



A

END (FRONT VERTICAL MOTOR [POWER SEAT TILT MOTOR ASSEMBLY RH] WAS DEFECTIVE)

B

27.REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY RH
27.REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY RH

Pre-procedure1

a.

Replace the power seat lifter motor assembly RH with a new or known good one.

HINT:

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL



b.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Procedure1

a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
Result:
Result Proceed to
B2658 is not output A
B2658 is output B



Post-procedure1

a.

None



A

END (POWER SEAT LIFTER MOTOR ASSEMBLY RH WAS DEFECTIVE)

B

28.REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)
28.REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)

Pre-procedure1

a.

Replace the slide motor (front seat adjuster assembly RH) with a new or known good one.

HINT:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY



b.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Procedure1

a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
Result:
Result Proceed to
B2658 is not output A
B2658 is output B



Post-procedure1

a.

None



A

END (SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY RH] WAS DEFECTIVE)

B

29.REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH)
29.REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH)

Pre-procedure1

a.

Replace the reclining motor (front seatback frame sub-assembly RH) with a new or known good one.

HINT:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY



b.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Procedure1

a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
Result:
Result Proceed to
B2658 is not output A
B2658 is output B



Post-procedure1

a.

None



A

END (RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY RH] WAS DEFECTIVE)

B

REPLACE POSITION CONTROL ECU ASSEMBLY RH