The position control ECU assembly LH (for LHD) or RH (for RHD) controls the power seat switch signal from the front power seat switch LH (for LHD) or RH (for RHD) and drives the motors.
for LHD:
for RHD:
*1: for LHD
*2: for RHD
Inspect the fuses for circuits related to this system before performing the following procedure.
Initializing the position control ECU assembly LH*1 or RH*2 will clear the seat position memory.
Make sure to initialize the position control ECU assembly LH*1 or RH*2 after replacing the seat assembly or any related parts (including removal and installation).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Check that each function of the power seat operates normally by using the front power seat switch LH.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| All power seat functions do not operate | A |
| One or more power seat functions do not operate | B |
A
B
Disconnect the L41 and L43 position control ECU assembly LH connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L41,L43)Location & Routingewd_type=routing;type=c,c;code=L41,L43 Click Connector(L41)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LHewd_type=component;type=c;code=L41;pinno=3 Click Connector(L43)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LHewd_type=component;type=c;code=L43;pinno=15,1 |
||
| L41-3 - Body ground | Ignition switch off | 11 to 14 V |
| L43-15 - Body ground | Ignition switch off | 11 to 14 V |
| L43-1 - Body ground | Ignition switch ON | 11 to 14 V |
| L43-1 - Body ground | Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L41)Location & Routingewd_type=routing;type=c;code=L41 Click Connector(L41)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LHewd_type=component;type=c;code=L41;pinno=2 |
||
| L41-2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the L34 front power seat switch LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L34)Location & Routingewd_type=routing;type=c;code=L34 Click Connector(L34)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Switch LHewd_type=component;type=c;code=L34;pinno=20 |
||
| L34-20 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that each function of the power seat operates normally by using the front power seat switch RH.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| All power seat functions do not operate | A |
| One or more power seat functions do not operate | B |
A
B
Disconnect the L15 and L17 position control ECU assembly RH connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L15,L17)Location & Routingewd_type=routing;type=c,c;code=L15,L17 Click Connector(L15)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RHewd_type=component;type=c;code=L15;pinno=3 Click Connector(L17)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RHewd_type=component;type=c;code=L17;pinno=15,1 |
||
| L15-3 - Body ground | Ignition switch off | 11 to 14 V |
| L17-15 - Body ground | Ignition switch off | 11 to 14 V |
| L17-1 - Body ground | Ignition switch ON | 11 to 14 V |
| L17-1 - Body ground | Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L15)Location & Routingewd_type=routing;type=c;code=L15 Click Connector(L15)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RHewd_type=component;type=c;code=L15;pinno=2 |
||
| L15-2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the L9 front power seat switch RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L9)Location & Routingewd_type=routing;type=c;code=L9 Click Connector(L9)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Switch RHewd_type=component;type=c;code=L9;pinno=11 |
||
| L9-11 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG