When the seat heater switch (rear left) is operated, the air conditioning amplifier assembly receives the signal from the cooler control assembly via the LIN communication line and operates the rear left side seat heater.
If the auxiliary battery voltage is low, the seat heater system may not operate. When "High Power Consumption Partial Limit on AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the auxiliary battery, referring to On-vehicle Inspection for the charging system.
Click herePower Source / Network>BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
If the seat heater system is operated when the auxiliary battery voltage is low, due to the electrical load limit control that gives voltage supply priority to the power steering system, the seat heater system may not operate. In this case, check the vehicle control history of the power steering system and check that "Battery Voltage Drop: X208F" is not stored before proceeding with troubleshooting.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>VEHICLE CONTROL HISTORY
Inspect the fuses for circuits related to this system before performing the following procedure.
Perform the Active Test according to the display on the GTS.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Left Seat Heater | Rear left side seat heater operation | OFF/ON | - |
| Tester Display |
|---|
| Rear Left Seat Heater |
Rear left side seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioner amplifier assembly with a new one or known good one.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| Proceed to |
|---|
| OK |
OK
Check the rear left side seat heater operation.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>OPERATION CHECK
Rear left side seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M3 seat heater control sub-assembly (rear seat LH) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(M3)Location & Routingewd_type=routing;type=c;code=M3 Click Connector(M3)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Heater Control Sub-Assembly LHewd_type=component;type=c;code=M3;pinno=1 |
||
| M3-1 (B1) - Body ground | Ignition switch ON | 11 to 14 V |
| M3-1 (B1) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the D79 air conditioning amplifier assembly connector.
Disconnect the M3 seat heater control sub-assembly (rear seat LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D79,M3)Location & Routingewd_type=routing;type=c,c;code=D79,M3 Click Connector(D79)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=D79;pinno=24 Click Connector(M3)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Heater Control Sub-Assembly LHewd_type=component;type=c;code=M3;pinno=5 |
||
| D79-24 (SM2L) - M3-5 (SWR) | Always | Below 1 Ω |
| D79-24 (SM2L) or M3-5 (SWR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M1 seatback heater assembly LH connector.
Disconnect the M3 seat heater control sub-assembly (rear seat LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(M1,M3)Location & Routingewd_type=routing;type=c,c;code=M1,M3 Click Connector(M1)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Heater Assembly LHewd_type=component;type=c;code=M1;pinno=4,1 Click Connector(M3)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Heater Control Sub-Assembly LHewd_type=component;type=c;code=M3;pinno=10,7 |
||
| M1-4 - M3-10(E) | Always | Below 1 Ω |
| M1-1 - M3-7(HTR) | Always | Below 1 Ω |
| M1-4 or M3-10 (E) - Body ground | Always | 10 kΩ or higher |
| M1-1 or M3-7(HTR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M1 seatback heater assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(M1)Location & Routingewd_type=routing;type=c;code=M1 Click Connector(M1)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Heater Assembly LHewd_type=component;type=c;code=M1;pinno=5 |
||
| M1-5 - Body ground | Always | Below 1 Ω |
| M1-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
OK
NG
Replace the seat heater control sub-assembly (rear seat LH) with a new one or known good one.
Click hereVehicle Interior>SEAT>SEAT HEATER CONTROL (for Rear Seat)>REMOVAL
| Proceed to |
|---|
| OK |
OK
Check the rear left side seat heater operation.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>OPERATION CHECK
Rear left side seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG