Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C125600  Accumulator Low Pressure Abnormality  


DESCRIPTION

The accumulator pressure sensor is built into the brake booster with master cylinder assembly and detects the accumulator pressure.

The No. 1 skid control ECU (brake booster with master cylinder assembly) turns on the brake system warning light (red indicator) and brake system warning light (yellow indicator), and sounds the meter buzzer if it senses a decrease in the accumulator pressure.

DTC C125600 may be stored if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C125600 Accumulator Low Pressure Abnormality Significant drop in accumulator pressure continues.
(DTCs will be stored and the buzzer will sound when the above condition is met.)
·

Accumulator pressure dropped due to frequent brake pedal operation (not a malfunction)

·

Pump motor malfunction

·

Accumulator deterioration

·

Accumulator pressure sensor (brake booster with master cylinder assembly)

·

Supply voltage reduced

·

Brake booster pump assembly

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
Only C125600 is output A
C125600 and other DTCs are output B



A

2.CHECK DTC

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Inspect the brake booster pump assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP>INSPECTION

OK:

The brake booster pump assembly is normal.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.READ VALUE USING GTS (MOTOR RELAY AND ACCUMULATOR PRESSURE)

NG

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

4.READ VALUE USING GTS (MOTOR RELAY AND ACCUMULATOR PRESSURE)

Pre-procedure1

a.

Reconnect the A39 brake booster pump assembly connector.


b.

Disconnect the A2 brake pedal stroke sensor assembly connector.


c.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


Procedure1

a.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa
Max.: 24.48 MPa
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
Accumulator Pressure
50003 466 96,212
Result:
Result Proceed to
The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. A
The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. B



Post-procedure1

a.

None



A

B

5.READ VALUE USING GTS (SERVO PRESSURE)
5.READ VALUE USING GTS (SERVO PRESSURE)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A2 brake pedal stroke sensor assembly connector.


Procedure1

a.

Perform the Active Test and operate the linear solenoid (SLR) in the brake booster with master cylinder assembly.


b.

Check that the servo pressure output value does not increase when performing the Active Test.

Chassis > Brake Booster > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
ECB Solenoid (SLR) Linear solenoid reduction valve (SLR) Solenoid Start (Activate)
Solenoid SLR
(It is possible to set the current)
Vehicle condition:
·

Vehicle stopped

·

Check that park (P) is selected

·

Apply the parking brake


ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa
Max.: 24.48 MPa
Brake pedal released: 0.00 to 1.53 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake Booster > Active Test
Active Test Display
ECB Solenoid (SLR)
Data List Display
Servo Pressure
50004 466 42 210
OK:

The servo pressure output value does not increase when performing the Active Test.


HINT:
·

If the servo pressure output value increases, an internal brake fluid leak in the brake booster with master cylinder assembly is suspected.

·

Perform the Active Test with the current set to maximum.



Result:
Result Proceed to
The servo pressure output value increases. A
The servo pressure output value does not increase. B



Post-procedure1

a.

None



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE BOOSTER PUMP ASSEMBLY

for Brake Booster with Master Cylinder Assembly for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for Brake Booster with Master Cylinder Assembly for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL

for Brake Booster Pump Assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP>REMOVAL