Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C05C051  Brake Pedal Position Sensor "A" Not Programmed  


DESCRIPTION

When the No. 1 skid control ECU (brake booster with master cylinder assembly) judges that the zero point calibration of the brake pedal stroke sensor assembly is incomplete, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C05C051 Brake Pedal Position Sensor "A" Not Programmed The brake pedal stroke sensor assembly zero point calibration is not performed.
(Normal brake pedal stroke sensor assembly zero point not memorized.)
·

Valid brake pedal stroke sensor assembly zero point not memorized.

(Calibration not performed or not completed)

·

Wire harness and connector

·

Brake pedal stroke sensor assembly


Brake Booster A Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
HINT:

During Dealer Mode, related DTCs are cleared.



CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

HINT:

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT




Result:
Proceed to
NEXT



NEXT

2.CLEAR ZERO POINT VALUE FOR BRAKE PEDAL STROKE SENSOR ASSEMBLY
2.CLEAR ZERO POINT VALUE FOR BRAKE PEDAL STROKE SENSOR ASSEMBLY
a.

Clear the zero point value for the brake pedal stroke sensor assembly.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


Chassis > Brake/EPB > Utility
Tester Display
Reset Memory
50005 435 4560

Result:
Proceed to
NEXT



NEXT

3.PERFORM BRAKE PEDAL STROKE SENSOR ASSEMBLY ZERO POINT CALIBRATION
3.PERFORM BRAKE PEDAL STROKE SENSOR ASSEMBLY ZERO POINT CALIBRATION
a.

Perform brake pedal stroke sensor assembly zero point calibration.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Result:
Result Proceed to
Only C05C051 is output A
DTCs are not output B
C05C051 and other DTCs are output C



Post-procedure1

a.

None



A

6.RECONFIRM DTC

B

END

C

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

6.RECONFIRM DTC
a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

7.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

7.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A2 brake pedal stroke sensor assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure3

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A2)Location & Routing

Click Connector(A2)Instrument Panel>Front Compartment Main Wire>Brake Pedal Stroke Sensor Assembly

A2-4 (VCSK) - A2-5 (SKG) Ignition switch ON 4.84 to 5.16 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR