Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C051D54  Multi-axis Acceleration Sensor Module "A" Missing Calibration  C121054  Yaw Rate Sensor Missing Calibration  


DESCRIPTION

The airbag ECU assembly has a built-in yaw rate and acceleration sensor.

The No. 2 skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag ECU assembly) and the CAN communication system, DTC U012587 is output. When DTC U012587 is output together with C051D54 and/or C121054, inspect and repair the trouble areas indicated by U012587 first.


These DTCs are also output when the calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C051D54 Multi-axis Acceleration Sensor Module "A" Missing Calibration Zero point calibration of acceleration sensor undone.
·

Acceleration sensor zero point not calibrated

·

Acceleration sensor (airbag ECU assembly) installation

·

Acceleration sensor (airbag ECU assembly)

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)
C121054 Yaw Rate Sensor Missing Calibration Zero point calibration of yaw rate sensor undone.
·

Yaw rate sensor zero point not calibrated

·

Yaw rate sensor (airbag ECU assembly) installation

·

Yaw rate sensor (airbag ECU assembly)

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag ECU assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C051D54 and C121054 are not output A
C051D54 or C121054 is output B



Post-procedure1

a.

None



A

END

B

4.CHECK AIRBAG ECU ASSEMBLY INSTALLATION
4.CHECK AIRBAG ECU ASSEMBLY INSTALLATION

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Check that the yaw rate and acceleration sensor (airbag ECU assembly) has been installed properly.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION


OK:

The yaw rate and acceleration sensor (airbag ECU assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag ECU assembly) is not installed in a tilted position.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)

NG

5.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Check the yaw rate and acceleration sensor output value displayed on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Sensor Value Yaw rate sensor value Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Chassis > Brake/EPB > Data List
Tester Display
Lateral G
Forward and Rearward G
Yaw Rate Sensor Value
50003 435 25,26,29
OK:

The yaw rate and acceleration sensor output value is normal.



Result:
Proceed to
OK
NG



OK

NG