Refer to DTC C110000.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C110000
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| P057A12 | Brake Pedal Position Sensor "A" Circuit Short to Battery | The sensor output voltage 1 (SKS1) is 4.7 V or more for 0.2 seconds or more. | ·
Wire harness and connector ·
Brake pedal stroke sensor assembly |
Brake Booster | A | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| P057A14 | Brake Pedal Position Sensor "A" Circuit Short to Ground or Open | The sensor output voltage 1 (SKS1) is less than 0.3 V for 0.2 seconds or more. | ·
Wire harness and connector ·
Brake pedal stroke sensor assembly |
Brake Booster | A | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| P057A1F | Brake Pedal Position Sensor "A" Circuit Intermittent | The difference between the current value and previous value of the sensor output voltage 1 (SKS1) is 8.5% or more for 0.2 seconds or more. | ·
Wire harness and connector ·
Brake pedal stroke sensor assembly |
Brake Booster | A | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
Refer to DTC C110000.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C110000
After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.
Check and adjust the brake pedal height.
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT
Adjust the brake pedal stroke sensor assembly.
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>INSTALLATION
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A2 brake pedal stroke sensor assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A5,A2)Location & Routingewd_type=routing;type=c,c;code=A5,A2 Click Connector(A2)Instrument Panel>Front Compartment Main Wire>Brake Pedal Stroke Sensor Assemblyewd_type=component;type=c;code=A2;pinno=6 |
||
| A5-3 (SKS1) - A2-6 (SKS1) | Always | Below 1 Ω |
| A5-3 (SKS1) or A2-6 (SKS1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>REMOVAL
NG