Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C050C14  Left Rear Wheel Speed Sensor Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC C050C12.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050C12

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C050C14 Left Rear Wheel Speed Sensor Circuit Short to Ground or Open An open in the speed sensor signal circuit continues for 0.5 seconds or more.
·

Rear speed sensor LH

·

Rear skid control sensor wire LH

·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING REAR SKID CONTROL SENSOR WIRE LH (MOMENTARY INTERRUPTION)

Pre-procedure1

a.

Select the line graph display on the GTS.


Procedure1

a.

Check for any momentary interruption in the wire harness and connector.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Speed Open Momentary interruption of rear speed sensor LH pulse input to ECU Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake/EPB > Data List
Tester Display
RL Speed Open
RL Speed Sensor Voltage Open
50003 435 104,113
NOTICE:

Perform the above inspection before removing the sensor and connector.


OK:

Normal (There are no momentary interruptions.)


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

2.INSPECT SKID CONTROL SENSOR WIRE REAR LH
2.INSPECT SKID CONTROL SENSOR WIRE REAR LH

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the WG2 rear skid control sensor wire LH connector.


b.

Disconnect the W3 rear skid control sensor wire LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(W3,WG2)Location & Routing

Click Connector(W3)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Speed Sensor LH

Click Connector(WG2)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Skid Control Sensor Wire LH and Floor Wire

W3-2 (RL+) - WG2-3 Always Below 1 Ω
W3-2 (RL+) or WG2-3 - Body ground and other terminals Always 10 kΩ or higher
W3-1 (RL-) - WG2-4 Always Below 1 Ω
W3-1 (RL-) or WG2-4 - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (REAR SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE SKID CONTROL SENSOR WIRE REAR LH

3.CHECK HARNESS AND CONNECTOR (REAR SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6,WG2)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

Click Connector(WG2)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Skid Control Sensor Wire LH and Floor Wire

A6-5 (RL+) - WG2-3 Always Below 1 Ω
A6-5 (RL+) or WG2-3 - Body ground Always 10 kΩ or higher
A6-4 (RL-) - WG2-4 Always Below 1 Ω
A6-4 (RL-) or WG2-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Reconnect the WG2 rear skid control sensor wire LH connector.


b.

Reconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(W3)Location & Routing

Click Connector(W3)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Speed Sensor LH

W3-2 (RL+) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG