Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C13DB00  Brake Pressure Too Low (Brake M/C1)  C13DD00  Brake Pressure Too Low (Brake M/C2)  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) controls the brake fluid pressure of each wheel cylinder based on the brake fluid pressure sensor.

DTCs may be stored if one of the following occurs:

·

Brake fluid leaks.

·

Wheel cylinder vibrates due to uneven wear of a brake disc.

·

Foreign matter enters a solenoid valve.

·

Line pressure drops during air bleeding.

·

Brake pads are replaced.

·

Rotors are replaced.

HINT:

When replacing the brake pads, retracting the brake caliper pistons and installing new brake pads will greatly increase the clearance between the brake pads and brake discs. This will result in a significant possibility of this DTC being stored the next time the brake pedal is depressed. As this is not a malfunction, clear the DTC if it is stored for this reason.



DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C13DB00 Brake Pressure Too Low (Brake M/C1) Fluid pressure control performance degraded (pressure excessively low)
·

Brake fluid leaks

·

Uneven brake disc rotor wear

·

Wire harness and connector

·

Brake actuator assembly


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
C13DD00 Brake Pressure Too Low (Brake M/C2) Fluid pressure control performance degraded (pressure excessively low)
·

Brake fluid leaks

·

Uneven brake disc rotor wear

·

Wire harness and connector

·

Brake actuator assembly


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA
a.

Interview the customer to check the vehicle conditions when the brake system warning light (yellow indicator) illuminated.


b.

Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.

Chassis > Brake/EPB > Trouble Codes
50001 435
HINT:

Freeze Frame Data is only stored once when a DTC is stored.



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

3.CHECK DTC
3.CHECK DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
Only C13DB00 or C13DD00 is output A
C13DB00 or C13DD00 and other DTCs are output B



Post-procedure1

a.

None



A

4.CHECK DTC

B

4.CHECK DTC
a.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Result:
Result Proceed to
DTCs are not output A
DTCs are output B




A

5.CHECK FOR FLUID LEAK

B

5.CHECK FOR FLUID LEAK
a.

Based on the Freeze Frame Data or interview with the customer, inspect the following items for brake fluid leaks:

·

The brake lines from the brake booster with master cylinder assembly to each wheel cylinder.

·

The main body of the brake booster with master cylinder assembly and brake actuator assembly.


OK:

There are no fluid leaks.



Result:
Proceed to
OK
NG



OK

6.CHECK BRAKE DISC

NG

REPAIR OR REPLACE APPLICABLE PART

6.CHECK BRAKE DISC

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Disconnect the A2 brake pedal stroke sensor assembly connector.


b.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

Uneven disc wear can be checked by measuring the disc thickness variation.

for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSPECTION



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.CLEAR DTC

NG

REPLACE BRAKE DISC

7.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

8.PERFORM AIR BLEEDING
8.PERFORM AIR BLEEDING
HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


Result:
Proceed to
NEXT



NEXT

9.CHECK BRAKE ACTUATOR ASSEMBLY (ACTUATOR SIDE)
9.CHECK BRAKE ACTUATOR ASSEMBLY (ACTUATOR SIDE)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

After 3 minutes elapse after turning the ignition switch off, disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

10.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)

NG

10.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)

Pre-procedure1

a.

Reconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure1

a.

Measure the voltage and resistance on the wire harness side.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU


OK:

Voltage and resistance readings are all normal.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

11.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
HINT:

If the system returns to normal, it is suspected that a DTC was stored due to a poor connection of a terminal in a connector, air in the system, etc.


Result:
Result Proceed to
C13DB00 and C13DD00 are not output A
C13DB00 or C13DD00 is output B



Post-procedure1

a.

None



A

B