Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  P057113  Brake Switch "A" Circuit Open  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch assembly.

The No. 2 skid control ECU (brake actuator assembly) incorporates a circuit to detect an open circuit.

This DTC is output when an open circuit is detected in the stop light signal input line.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
P057113 Brake Switch "A" Circuit Open When the voltage at terminal +BS is 9.5 V or more and the stop light drive output (STPO) is off, an open in the STP circuit is detected for 0.3 seconds or more.
·

Wire harness and connector

·

Stop light switch assembly

·

No. 2 skid control ECU (brake actuator assembly)

·

No. 2 semiconductor power integration ECU

·

STP circuit


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.


Result:
Result Proceed to
All stop lights illuminate when the brake pedal is depressed and turn off when the brake pedal is released. A
All stop lights do not illuminate when the brake pedal is depressed. B
One or more stop lights illuminate when the brake pedal is depressed but remain on when the brake pedal is released. C



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

B

11.CHECK NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

C

6.CHECK STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Check the value of Stop Light SW when the brake pedal is depressed.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly status
(STP or STP2 terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:
·

Stop light control relay off: STP terminal status displayed.

·

Stop light control relay on: STP2 terminal status displayed.



Chassis > Brake/EPB > Data List
Tester Display
Stop Light SW
50003 435 59

Result:
Result Proceed to
The value of Stop Light SW is ON A
None of the above conditions are met B



A

3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION

B

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure2

a.
C447332C03
0.448,0.448 0.781,0.698 0.333,0.25 2.25,1.708 1.896,1.073 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.531,0.51 0.99,0.708 0.458,0.198 10 false A3 2.25,1.719 2.708,1.917 0.458,0.198 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-2 (L) - Body ground
·

Ignition switch ON

·

The headlights are on

·

The blower motor switch is in the HI position

·

The rear window defogger is turned on

·

Stop light switch assembly off (Brake pedal released)


Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CLEAR DTC

NG

6.CHECK STOP LIGHT SWITCH ASSEMBLY
4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
P057113 is not output A
P057113 is output B



Post-procedure1

a.

None



A

B

6.CHECK STOP LIGHT SWITCH ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A3 stop light switch assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-2 (L) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

7.CHECK BRAKE ACTUATOR ASSEMBLY
7.CHECK BRAKE ACTUATOR ASSEMBLY

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-2 (L) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

9.CHECK NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU
8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-2 (L) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the L111 No. 2 semiconductor power integration ECU connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-2 (L) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

NG

10.CHECK FOR SHORT TO +B IN STP CIRCUIT
10.CHECK FOR SHORT TO +B IN STP CIRCUIT
a.

Check that there is no short to +B in the STP circuit (wire harnesses, connectors, ECUs and stop lights).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART

11.CHECK NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.
C372881C20
1.604,0.167 1.979,0.354 0.375,0.188 2.99,1.74 2.99,1.573 2.99,1.573 1.927,1.01 true 1.646,0.188 2.104,0.385 0.458,0.198 10 false G102 2.896,1.781 3.302,1.958 0.406,0.177 10 false STP 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Component with harness connected
(No. 2 Semiconductor Power Integration ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G102)Location & Routing

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

G102-10 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

NG

12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU)
12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU)
a.

Check that there is no open in the wire harnesses and connectors from terminal L of the stop light switch assembly to the No. 2 semiconductor power integration ECU.

OK:

No open.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR