Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C13807E  Stop Lamp Relay Actuator Stuck On  


DESCRIPTION

When any of the following conditions are met, the No. 2 skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light control relay (No. 2 semiconductor power integration ECU) and turns on the stop lights.

Illumination Conditions:
·

Pre-collision brake is operating.

·

The dynamic radar cruise control system is operating and is applying the brakes.

·

Secondary collision brake is operating.

·

Brake hold is operating.

·

The parking brake is engaged while the vehicle is being driven.

·

Advanced park is operating


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C13807E Stop Lamp Relay Actuator Stuck On When the IG1 terminal voltage exceeds 10 V and the +BS terminal voltage is 9.5 V or higher, stop light drive output (STPO) is OFF, STP is OFF and STP2 is ON continuously for 5 seconds or more.
·

Wire harness and connector

·

Stop light switch assembly

·

No. 2 skid control ECU (brake actuator assembly)

·

No. 2 semiconductor power integration ECU

·

STP circuit

·

STP2 circuit


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)

WIRING DIAGRAM

C447257E03
2.146,0.313 3.188,0.51 1.042,0.198 10 false to Each ECU 5.083,0.979 7.083,1.188 2,0.208 10 false Stop Light Switch Assembly 0.208,5.344 1.969,5.708 1.76,0.365 10 false No. 2 Semiconductor Power Integration ECU 5.042,5.25 6.979,5.615 1.938,0.365 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 1.813,6.24 3.167,6.448 1.354,0.208 10 false to Stop Light Circuit 5.24,3.208 5.854,3.406 0.615,0.198 10 false STPO 5.25,4.365 5.865,4.563 0.615,0.198 10 false STP2 5.24,0.323 5.854,0.521 0.615,0.198 10 false L 5.25,2.073 5.865,2.271 0.615,0.198 10 false STP 1.531,4.26 2.146,4.458 0.615,0.198 10 false OUT 1.531,3.323 2.146,3.521 0.615,0.198 10 false ACC 1.563,2.188 2.177,2.385 0.615,0.198 10 false STP 1.156,4.375 1.615,4.573 0.458,0.198 10 false IPD 1.104,4.052 1.417,4.25 0.313,0.198 10 false +B 0.208,5.156 0.823,5.354 0.615,0.198 10 false G102 5.042,5.063 5.656,5.26 0.615,0.198 10 false A6 5.083,0.792 5.698,0.99 0.615,0.198 10 false A3 4.969,4.26 5.281,4.458 0.313,0.198 10 false 37 4.969,3.208 5.281,3.406 0.313,0.198 10 false 32 4.969,2.073 5.281,2.271 0.313,0.198 10 false 11 5.042,0.198 5.354,0.396 0.313,0.198 10 false 2 1.917,2.073 2.229,2.271 0.313,0.198 10 false 10 1.917,3.208 2.229,3.406 0.313,0.198 10 false 14 1.917,4.26 2.229,4.458 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


HINT:

When DTC P057112 and/or P057113 are output together with DTC C13807E, inspect and repair the trouble areas indicated by DTC P057112 and/or P057113 first.

for P057112: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>P057112

for P057113: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>P057113


PROCEDURE

1.CHECK STOP LIGHT ILLUMINATION STATUS
a.

With the brake pedal released, check the illumination status of the stop lights.


Result:
Result Proceed to
The stop lights are illuminated. A
The stop lights are not illuminated. B



A

2.CHECK BRAKE ACTUATOR ASSEMBLY

B

5.CHECK BRAKE ACTUATOR ASSEMBLY
2.CHECK BRAKE ACTUATOR ASSEMBLY

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-37 (STP2) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

3.CHECK NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU
3.CHECK NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-37 (STP2) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

4.CHECK FOR SHORT TO +B IN STP2 CIRCUIT
4.CHECK FOR SHORT TO +B IN STP2 CIRCUIT
a.

Check that there is no short to +B in the STP2 circuit (wire harnesses, connectors, stop lights and ECUs).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART

5.CHECK BRAKE ACTUATOR ASSEMBLY

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-11 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

6.CHECK NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU
6.CHECK NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-11 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

NG

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.
C447332C01
0.448,0.448 0.781,0.698 0.333,0.25 2.25,1.708 1.896,1.073 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.531,0.51 0.99,0.708 0.458,0.198 10 false A3 2.25,1.719 2.708,1.917 0.458,0.198 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-2 (L) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

8.CHECK FOR SHORT TO GROUND IN STP CIRCUIT
8.CHECK FOR SHORT TO GROUND IN STP CIRCUIT
a.

Check that there is no short to ground in the STP circuit (wire harnesses, connectors and ECUs)

OK:

There is no short to ground.



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PART