Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A8111  Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground  P0A814B  Hybrid/EV Battery Cooling Fan 1 Over Temperature  


DESCRIPTION

The battery cooling blower assembly speed is controlled by the battery ECU assembly. The power source of the battery cooling blower assembly is supplied by turning the IGCT No. 2 relay and BATT FAN relay ON by the MREL terminal of the EV control ECU. The battery ECU assembly sends command signals (SI0) to the battery cooling blower assembly to adjust the fan speed to an appropriate speed for the EV battery temperature. The frequency (FP0) of the battery cooling blower assembly is sent to the battery ECU assembly as a monitor signal.

A377319E02
0.26,2.344 2.385,2.76 2.125,0.417 10 false Battery Cooling Blower Assembly 2.99,1.104 4.865,1.667 1.875,0.563 10 false SI0 (Command Signal) 2.979,1.948 4.625,2.458 1.646,0.51 10 false FP0 (Monitor Signal) 5.156,2.427 6.885,2.75 1.729,0.323 10 false Battery ECU Assembly

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0A8111 Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground Both of the following conditions are met:
·

The speed calculated based on the battery cooling blower assembly output frequency is not within the target control speed range.

·

The battery cooling blower assembly speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking).


(2 trip detection logic)
·

Battery cooling blower assembly

·

Battery ECU assembly

·

BATT FAN fuse

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0A814B Hybrid/EV Battery Cooling Fan 1 Over Temperature Both of the following conditions are met:
·

The EV battery temperature is high and the speed calculated based on the battery cooling blower assembly output frequency is not within the target control speed range.

·

The EV battery temperature is high and the battery cooling blower assembly speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking).


(1 trip detection logic)
·

Battery cooling blower assembly

·

Battery ECU assembly

·

BATT FAN fuse

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A

Related Data List
DTC No. Data List
P0A8111
·

Hybrid/EV Battery Cooling Fan 1 Drive Request

·

Hybrid/EV Battery Cooling Fan 1 Drive Status

·

Hybrid/EV Battery Cooling Fan 1 Frequency


P0A814B

The following items can be helpful when performing repairs:

Data List
·

Hybrid/EV Battery Temperature 1 to 6

·

BATT Voltage


HINT:

"Hybrid/EV Battery Cooling Fan 1 Frequency" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly speed.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Enter the following menus: Powertrain / EV Battery / Active Test / Control the Hybrid/EV Battery Cooling Fan.

4.

Select fan mode 1 and operate the battery cooling blower assembly and wait for 60 seconds or more.

HINT:

Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct.


5.

Enter the following menus: Powertrain / EV Battery / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

for LHD:
C374191E04
5.74,4.25 6.198,4.448 0.458,0.198 10 false GND 5.74,4.615 6.198,4.813 0.458,0.198 10 false GND1 5.479,4.542 5.792,4.74 0.313,0.198 10 false 31 5.479,4.146 5.792,4.344 0.313,0.198 10 false 11 5.719,3.615 6.177,3.813 0.458,0.198 10 false SI0 5.708,2.771 6.167,2.969 0.458,0.198 10 false FP0 5.458,2.76 5.771,2.958 0.313,0.198 10 false 32 5.469,3.604 5.781,3.802 0.313,0.198 10 false 33 3.344,2.781 3.802,2.979 0.458,0.198 10 false FP0 2.469,2.469 2.927,2.667 0.458,0.198 10 false SI0 2.427,2.781 2.885,2.979 0.458,0.198 10 false GND0 3.375,2.469 3.833,2.667 0.458,0.198 10 false IG0 3.708,2.458 3.865,2.656 0.156,0.198 10 false 1 3.719,2.771 3.875,2.969 0.156,0.198 10 false 2 2.281,2.458 2.438,2.656 0.156,0.198 10 false 3 2.281,2.771 2.438,2.969 0.156,0.198 10 false 4 2.125,1.719 3.5,1.917 1.375,0.198 10 false IGCT NO. 2 2.125,1.229 3.5,1.427 1.375,0.198 10 false IGCT NO. 6 3.219,0.75 4.594,0.948 1.375,0.198 10 false BATT FAN 2.198,0.385 3.573,0.583 1.375,0.198 10 false BATT FAN 3.219,2.115 4.594,2.313 1.375,0.198 10 false IGCT NO. 2 0.958,1.688 1.417,1.885 0.458,0.198 10 false MREL 1.458,1.708 1.75,1.906 0.292,0.198 10 false 21 0.063,0.229 1.177,0.469 1.115,0.24 10 false Auxiliary Battery 4.771,2.802 5.229,3 0.458,0.198 10 false FP0 4.198,2.802 4.656,3 0.458,0.198 10 false FP0 4.823,3.615 5.281,3.813 0.458,0.198 10 false SI0 4.198,3.615 4.656,3.813 0.458,0.198 10 false SI0 3.948,2.781 4.24,2.99 0.292,0.208 10 false 12 5.125,2.76 5.417,2.969 0.292,0.208 10 false 12 4.01,3.604 4.302,3.813 0.292,0.208 10 false 3 3.208,0.146 3.5,0.354 0.292,0.208 10 false 3 5.156,3.604 5.448,3.813 0.292,0.208 10 false 3 3.781,0.146 4.073,0.354 0.292,0.208 10 false 5 3.208,0.385 3.5,0.594 0.292,0.208 10 false 1 3.792,0.396 4.083,0.604 0.292,0.208 10 false 2 3.802,1.729 4.094,1.938 0.292,0.208 10 false 1 3.208,1.729 3.5,1.938 0.292,0.208 10 false 2 3.802,1.479 4.094,1.688 0.292,0.208 10 false 5 3.208,1.469 3.5,1.677 0.292,0.208 10 false 3 4.167,4.521 4.625,4.719 0.458,0.198 10 false GND1 4.677,4.521 5.135,4.719 0.458,0.198 10 false GND1 4.74,4.156 5.198,4.354 0.458,0.198 10 false GND 4.177,4.156 4.635,4.354 0.458,0.198 10 false GND 5.135,4.156 5.448,4.354 0.313,0.198 10 false 1 3.99,4.156 4.302,4.354 0.313,0.198 10 false 1 3.927,4.521 4.24,4.719 0.313,0.198 10 false 10 5.094,4.531 5.406,4.729 0.313,0.198 10 false 10 2.604,0.125 2.76,0.323 0.156,0.198 10 false 2 2.229,0.917 2.385,1.115 0.156,0.198 10 false 2 2.594,1.469 2.75,1.667 0.156,0.198 10 false 2 2.219,0.125 2.375,0.323 0.156,0.198 10 false 1 2.615,0.927 2.771,1.125 0.156,0.198 10 false 1 2.219,1.469 2.375,1.667 0.156,0.198 10 false 1 0.469,3.906 1.885,4.292 1.417,0.385 10 false EV Control ECU 0.125,3.906 0.417,4.094 0.292,0.188 10 false A8 2.021,3.229 6.76,3.427 4.74,0.198 10 false Battery Cooling Blower Assembly 1.667,3.229 2.052,3.406 0.385,0.177 10 false G31 5.667,5.292 7.156,5.552 1.49,0.26 10 false Battery ECU Assembly 5.406,5.292 5.667,5.49 0.26,0.198 10 false z26 3.906,4.979 5.323,5.375 1.417,0.396 10 false No. 2 EV Battery Pack Wire Connector 3.406,4.99 3.802,5.167 0.396,0.177 10 false G156

for RHD:
C374191E05
5.74,4.25 6.198,4.448 0.458,0.198 10 false GND 5.74,4.615 6.198,4.813 0.458,0.198 10 false GND1 5.479,4.542 5.792,4.74 0.313,0.198 10 false 31 5.479,4.146 5.792,4.344 0.313,0.198 10 false 11 5.719,3.615 6.177,3.813 0.458,0.198 10 false SI0 5.708,2.771 6.167,2.969 0.458,0.198 10 false FP0 5.458,2.76 5.771,2.958 0.313,0.198 10 false 32 5.469,3.604 5.781,3.802 0.313,0.198 10 false 33 3.344,2.781 3.802,2.979 0.458,0.198 10 false FP0 2.469,2.469 2.927,2.667 0.458,0.198 10 false SI0 2.427,2.781 2.885,2.979 0.458,0.198 10 false GND0 3.375,2.469 3.833,2.667 0.458,0.198 10 false IG0 3.708,2.458 3.865,2.656 0.156,0.198 10 false 1 3.719,2.771 3.875,2.969 0.156,0.198 10 false 2 2.281,2.458 2.438,2.656 0.156,0.198 10 false 3 2.281,2.771 2.438,2.969 0.156,0.198 10 false 4 2.125,1.719 3.5,1.917 1.375,0.198 10 false IGCT NO. 2 2.125,1.229 3.5,1.427 1.375,0.198 10 false IGCT NO. 6 3.219,0.75 4.594,0.948 1.375,0.198 10 false BATT FAN 2.198,0.385 3.573,0.583 1.375,0.198 10 false BATT FAN 3.219,2.115 4.594,2.313 1.375,0.198 10 false IGCT NO. 2 0.958,1.688 1.417,1.885 0.458,0.198 10 false MREL 1.458,1.708 1.75,1.906 0.292,0.198 10 false 21 0.063,0.229 1.177,0.469 1.115,0.24 10 false Auxiliary Battery 4.771,2.802 5.229,3 0.458,0.198 10 false FP0 4.198,2.802 4.656,3 0.458,0.198 10 false FP0 4.823,3.615 5.281,3.813 0.458,0.198 10 false SI0 4.198,3.615 4.656,3.813 0.458,0.198 10 false SI0 3.948,2.781 4.24,2.99 0.292,0.208 10 false 12 5.125,2.76 5.417,2.969 0.292,0.208 10 false 12 4.01,3.604 4.302,3.813 0.292,0.208 10 false 3 3.208,0.146 3.5,0.354 0.292,0.208 10 false 3 5.156,3.604 5.448,3.813 0.292,0.208 10 false 3 3.781,0.146 4.073,0.354 0.292,0.208 10 false 5 3.208,0.385 3.5,0.594 0.292,0.208 10 false 1 3.792,0.396 4.083,0.604 0.292,0.208 10 false 2 3.802,1.729 4.094,1.938 0.292,0.208 10 false 1 3.208,1.729 3.5,1.938 0.292,0.208 10 false 2 3.802,1.479 4.094,1.688 0.292,0.208 10 false 5 3.208,1.469 3.5,1.677 0.292,0.208 10 false 3 4.167,4.521 4.625,4.719 0.458,0.198 10 false GND1 4.677,4.521 5.135,4.719 0.458,0.198 10 false GND1 4.74,4.156 5.198,4.354 0.458,0.198 10 false GND 4.177,4.156 4.635,4.354 0.458,0.198 10 false GND 5.135,4.156 5.448,4.354 0.313,0.198 10 false 1 3.99,4.156 4.302,4.354 0.313,0.198 10 false 1 3.927,4.521 4.24,4.719 0.313,0.198 10 false 10 5.094,4.531 5.406,4.729 0.313,0.198 10 false 10 2.604,0.125 2.76,0.323 0.156,0.198 10 false 2 2.229,0.917 2.385,1.115 0.156,0.198 10 false 2 2.594,1.469 2.75,1.667 0.156,0.198 10 false 2 2.219,0.125 2.375,0.323 0.156,0.198 10 false 1 2.615,0.927 2.771,1.125 0.156,0.198 10 false 1 2.219,1.469 2.375,1.667 0.156,0.198 10 false 1 0.469,3.906 1.885,4.292 1.417,0.385 10 false EV Control ECU 0.125,3.906 0.521,4.094 0.396,0.188 10 false D15 2.021,3.229 6.76,3.427 4.74,0.198 10 false Battery Cooling Blower Assembly 1.667,3.229 2.052,3.406 0.385,0.177 10 false G31 5.667,5.292 7.156,5.552 1.49,0.26 10 false Battery ECU Assembly 5.406,5.292 5.667,5.49 0.26,0.198 10 false z26 3.906,4.979 5.323,5.375 1.417,0.396 10 false No. 2 EV Battery Pack Wire Connector 3.406,4.99 3.802,5.167 0.396,0.177 10 false G156

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

As the battery cooling blower assembly speed is excessively low, there is a possibility of an open or short to ground in connected circuits, or motor locking.


PROCEDURE

1.CHECK DTC OUTPUT (EV BATTERY, EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV Battery > Trouble Codes
50001 398
Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0A8111 or P0A814B for Hybrid battery system is output A
P0A8111 or P0A814B is output and DTCs other than the DTCs in the table below are output B
P0A8111 or P0A814B is output and Hybrid battery system DTCs in the table below are output C
P0A8111 or P0A814B is output and Hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

a.

Turn the ignition switch off.



A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID/EV BATTERY COOLING FAN)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID/EV BATTERY COOLING FAN)

C

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

D

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID/EV BATTERY COOLING FAN)

Pre-procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > EV Battery > Clear DTCs
50002 398

Procedure1

a.

Select air volume mode 6 in the "Control the Hybrid/EV Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

Powertrain > EV Battery > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid/EV Battery Cooling Fan Battery cooling blower assembly operation and blower volume can be checked. OFF, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > EV Battery > Active Test
Tester Display
Control the Hybrid/EV Battery Cooling Fan
50004 398 1
NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check if the fan operates and air is sucked. In accordance with fail-safe system operation, the battery ECU assembly sends a command to operate the battery cooling blower assembly.



b.

Check that the battery cooling blower assembly operates, air is sucked into the inlet duct and the operation sound is normal.

HINT:

The battery cooling blower assembly may not stop even when turning the cooling fan off in the "Control the Hybrid/EV Battery Cooling Fan" Active Test. This is due to HV system control and is not a malfunction.


OK:

The battery cooling blower assembly operates.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BATTERY COOLING BLOWER ASSEMBLY)

NG

9.CHECK FUSE (BATT FAN)
3.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382283N03
2.698,0.25 3.167,0.469 0.469,0.219 2.635,1.354 3,1.552 0.365,0.198 2.75,0.281 3.135,0.417 0.385,0.135 10 true G156 2.688,1.385 2.979,1.542 0.292,0.156 10 true G31

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Disconnect the G31 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C371973C11
1.51,0.146 1.958,0.385 0.448,0.24 1.542,1.76 1.958,1.99 0.417,0.229 1.844,2.625 2.365,2.333 true 0.458,0.906 1.406,1.229 true 1.563,0.198 1.958,0.375 0.396,0.177 10 false G156 1.635,1.813 1.938,1.99 0.302,0.177 10 false G31 2.479,2.198 2.938,2.396 0.458,0.198 10 false FP0 0.177,0.781 0.635,0.979 0.458,0.198 10 false FP0 0.156,0.083 0.469,0.24 0.313,0.156 10 false *a 0.177,1.875 0.49,2.031 0.313,0.156 10 false *b
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,G31)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(G31)Body>Floor Wire / No. 3 Floor Wire>Battery Cooling Blower Assembly

G156-12 (FP0) - G31-2 (FP0) Ignition switch off Below 1 Ω
G156-12 (FP0) or G31-2 (FP0) - Body ground and other terminals Ignition switch off 10 kΩ or higher



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,G31)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(G31)Body>Floor Wire / No. 3 Floor Wire>Battery Cooling Blower Assembly

G156-12 (FP0) - G31-2 (FP0) - Body ground Ignition switch ON Below 1 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip and FC converter power outlet cable removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the G31 battery cooling blower assembly connector.


d.

Reconnect the G156 No. 2 EV battery pack wire connector.


e.

Install the center No. 2 floor to brace extension.



OK

4.READ VALUE USING GTS (HYBRID/EV BATTERY COOLING FAN 1 FREQUENCY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (HYBRID/EV BATTERY COOLING FAN 1 FREQUENCY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs and freeze frame data.

Powertrain > EV Battery > Clear DTCs
50002 398

Procedure1

a.

Select each air volume mode (1 to 6) in the "Control the Hybrid/EV Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

Powertrain > EV Battery > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid/EV Battery Cooling Fan Battery cooling blower assembly operation and blower volume can be checked. OFF, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > EV Battery > Active Test
Active Test Display
Control the Hybrid/EV Battery Cooling Fan
Data List Display
Hybrid/EV Battery Cooling Fan 1 Frequency
50004 398 1 54
NOTICE:

If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the battery ECU assembly sends a command to operate the battery cooling fan assembly.



b.
C382282C11
1.521,2.448 2.021,2.667 0.5,0.219 2.49,3.49 2.844,3.188 true 2.104,3.844 2.74,4.26 true 0.135,0.104 0.354,0.292 0.219,0.188 10 true *a 1.594,2.49 2.073,2.656 0.479,0.167 10 false G156 2.906,3.094 3.229,3.25 0.323,0.156 10 false GND 2.823,4.219 3.146,4.375 0.323,0.156 10 false FP0
*a Component with harness connected
(No. 2 EV Battery Pack Wire Connector)


While the cooling fan is operating, compare the value in the Data List (Hybrid/EV Battery Cooling Fan 1 Frequency) with the frequency value that was actually measured at the battery ECU assembly connector.

Specified Condition:
Tester Connection Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-12 (FP0) - G156-1 (GND) Battery cooling blower assembly is operating.


NOTICE:

Turning the ignition switch to ON with the service plug grip and FC converter power outlet cable removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.



Result:
Result Proceed to
Both of the value in the Data List (Hybrid/EV Battery Cooling Fan 1 Frequency) and the actual measured value at the battery ECU assembly connector are 0 Hz. A
Other than above B


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Install the center No. 2 floor to brace extension.



A

5.CHECK BATTERY ECU ASSEMBLY

B

7.CHECK BATTERY ECU ASSEMBLY (HYBRID/EV BATTERY COOLING FAN 1 FREQUENCY)
5.CHECK BATTERY ECU ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382284N03
2.635,1.406 3.042,1.604 0.406,0.198 2.677,1.417 3.01,1.583 0.333,0.167 10 true G31

Disconnect the G31 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.
C371974C17
1.573,0.281 1.948,0.479 0.375,0.198 1.927,1.75 2.427,1.927 true 1.917,1.354 2.427,1.229 true 0.135,0.135 0.448,0.292 0.313,0.156 10 false *a 2.521,1.125 2.979,1.323 0.458,0.198 10 false FP0 2.531,1.875 3.146,2.073 0.615,0.198 10 false GND0 1.656,0.323 2.115,0.521 0.458,0.198 10 false G31
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G31)Location & Routing

Click Connector(G31)Body>Floor Wire / No. 3 Floor Wire>Battery Cooling Blower Assembly

G31-2 (FP0) - G31-4 (GND0) Ignition switch ON 4.5 to 5.5 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip and FC converter power outlet cable removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the G31 battery cooling blower assembly connector.


d.

Install the center No. 2 floor to brace extension.



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No.1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374185C45
1.469,1.667 1.969,1.927 0.5,0.26 1.49,0.073 1.99,0.333 0.5,0.26 2.021,1.01 2.771,0.563 true 0.615,1.76 1.521,2.604 true 0.063,0.073 0.375,0.229 0.313,0.156 10 false *a 0.083,1.448 0.396,1.604 0.313,0.156 10 false *b 1.625,1.74 1.938,1.938 0.313,0.198 10 false z26 1.583,0.146 1.958,0.333 0.375,0.188 10 false G156 2.906,0.448 3.365,0.646 0.458,0.198 10 false FP0 0.344,1.625 0.802,1.823 0.458,0.198 10 false FP0
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,z26)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

G156-12 (FP0) - z26-32 (FP0) Always Below 1 Ω
G156-12 (FP0) or z26-32 (FP0) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No.1 EV battery cover sub-assembly.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK BATTERY ECU ASSEMBLY (HYBRID/EV BATTERY COOLING FAN 1 FREQUENCY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs and freeze frame data.

Powertrain > EV Battery > Clear DTCs
50002 398

Procedure1

a.

Select each air volume mode (1 to 6) in the "Control the Hybrid/EV Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

Powertrain > EV Battery > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid/EV Battery Cooling Fan Battery cooling blower assembly operation and blower volume can be checked. OFF, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > EV Battery > Active Test
Active Test Display
Control the Hybrid/EV Battery Cooling Fan
Data List Display
Hybrid/EV Battery Cooling Fan 1 Frequency
50004 398 1 54
NOTICE:

If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the battery ECU assembly sends a command to operate the battery cooling blower assembly.



b.
C382282C12
1.531,2.448 1.979,2.698 0.448,0.25 2.49,3.49 2.844,3.188 true 2.104,3.844 2.74,4.26 true 0.135,0.104 0.354,0.292 0.219,0.188 10 true *a 1.594,2.49 1.979,2.667 0.385,0.177 10 false G156 2.906,3.094 3.229,3.25 0.323,0.156 10 false GND 2.823,4.219 3.146,4.375 0.323,0.156 10 false FP0
*a Component with harness connected
(No. 2 EV Battery Pack Wire Connector)


While the cooling fan is operating, compare the value in the Data List (Hybrid/EV Battery Cooling Fan 1 Frequency) with the frequency value that was actually measured at the battery ECU assembly connector.

Specified Condition:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-12 (FP0) - G156-1 (GND) Battery cooling blower assembly is operating. Difference between the value in the Data List (Hybrid/EV Battery Cooling Fan 1 Frequency) and the actual measured value at the battery ECU assembly connector is 10% or less.


NOTICE:

Turning the ignition switch to ON with the service plug grip and FC converter power outlet cable removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Install the center No. 2 floor to brace extension.



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
8.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374185C45
1.469,1.667 1.969,1.927 0.5,0.26 1.49,0.073 1.99,0.333 0.5,0.26 2.021,1.01 2.771,0.563 true 0.615,1.76 1.521,2.604 true 0.063,0.073 0.375,0.229 0.313,0.156 10 false *a 0.083,1.448 0.396,1.604 0.313,0.156 10 false *b 1.625,1.74 1.938,1.938 0.313,0.198 10 false z26 1.583,0.146 1.958,0.333 0.375,0.188 10 false G156 2.906,0.448 3.365,0.646 0.458,0.198 10 false FP0 0.344,1.625 0.802,1.823 0.458,0.198 10 false FP0
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,z26)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

G156-12 (FP0) - z26-32 (FP0) Always Below 1 Ω
G156-12 (FP0) or z26-32 (FP0) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK FUSE (BATT FAN)

Pre-procedure1

a.
A479022C01
0.885,1.583 1.24,0.688 true 0.156,0.927 0.469,1.125 0.313,0.198 10 false *1 1.177,0.51 1.49,0.708 0.313,0.198 10 false *a
*1 Luggage Room Relay Block Assembly
*a BATT FAN Fuse


Remove the BATT FAN fuse from the luggage room relay block assembly.


Procedure1

a.

Measure the resistance of the BATT FAN fuse.

Standard Resistance:
Tester Connection Condition Specified Condition
BATT FAN fuse terminals 1 - 2 Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the BATT FAN fuse to the luggage room relay block assembly.



OK

10.CHECK HARNESS AND CONNECTOR (BATT FAN RELAY - BATTERY COOLING BLOWER ASSEMBLY) (VOLTAGE)

NG

20.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATT FAN FUSE)
10.CHECK HARNESS AND CONNECTOR (BATT FAN RELAY - BATTERY COOLING BLOWER ASSEMBLY) (VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382284N03
2.635,1.406 3.042,1.604 0.406,0.198 2.677,1.417 3.01,1.583 0.333,0.167 10 true G31

Disconnect the G31 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs and freeze frame data.

Powertrain > EV Battery > Clear DTCs
50002 398

Procedure1

a.
C371974C18
1.573,0.281 1.948,0.479 0.375,0.198 1.927,1.75 2.427,1.927 true 1.042,1.073 1.625,1.323 true 0.135,0.135 0.448,0.292 0.313,0.156 10 false *a 0.708,1.01 1.167,1.208 0.458,0.198 10 false IG0 2.531,1.875 3.146,2.073 0.615,0.198 10 false GND0 1.635,0.323 2.094,0.521 0.458,0.198 10 false G31
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G31)Location & Routing

Click Connector(G31)Body>Floor Wire / No. 3 Floor Wire>Battery Cooling Blower Assembly

G31-1 (IG0) - G31-4 (GND0) Ignition switch ON 11 to 14 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip and FC converter power outlet cable removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

Turning the ignition switch to ON with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

·

Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)

·

Fuse condition (before and after removing fuse(s)) (IG circuit)

·

Connection condition of connectors (IG circuit)

·

Wire harness condition (IG circuit)

·

Wire harness condition (GND circuit)




Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Connect the G31 battery cooling blower assembly connector.


d.

Install the center No. 2 floor to brace extension.



OK

11.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BATTERY COOLING BLOWER ASSEMBLY)

NG

16.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND)
11.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382283N03
2.698,0.25 3.167,0.469 0.469,0.219 2.635,1.354 3,1.552 0.365,0.198 2.75,0.281 3.135,0.417 0.385,0.135 10 true G156 2.688,1.385 2.979,1.542 0.292,0.156 10 true G31

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Disconnect the G31 battery cooling blower assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
C371973C12
1.51,0.146 1.927,0.375 0.417,0.229 1.542,1.76 1.958,1.99 0.417,0.229 0.948,2.708 1.594,2.885 true 0.479,0.844 1.417,1.083 true 1.563,0.198 2.021,0.396 0.458,0.198 10 false G156 1.635,1.813 2.094,2.01 0.458,0.198 10 false G31 0.177,0.781 0.635,0.979 0.458,0.198 10 false SI0 0.156,0.083 0.469,0.24 0.313,0.156 10 false *a 0.177,1.875 0.49,2.031 0.313,0.156 10 false *b 0.635,2.604 1.094,2.802 0.458,0.198 10 false SI0
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,G31)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(G31)Body>Floor Wire / No. 3 Floor Wire>Battery Cooling Blower Assembly

G156-3 (SI0) - G31-3 (SI0) Ignition switch off Below 1 Ω
G156-3 (SI0) or G31-3 (SI0) - Body ground and other terminals Ignition switch off 10 kΩ or higher



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,G31)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(G31)Body>Floor Wire / No. 3 Floor Wire>Battery Cooling Blower Assembly

G156-3 (SI0) or G31-3 (SI0) - Body ground Ignition switch ON Below 1 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip and FC converter power outlet cable removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the G31 battery cooling blower assembly connector.


d.

Reconnect the G156 No. 2 EV battery pack wire connector.


e.

Install the center No. 2 floor to brace extension.



OK

12.CHECK BATTERY ECU ASSEMBLY (SI0 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK BATTERY ECU ASSEMBLY (SI0 VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
C382282C13
1.51,2.5 1.938,2.719 0.427,0.219 2.469,3.5 2.885,3.083 true 2.073,3.49 0.531,3.146 true 0.104,0.104 0.333,0.281 0.229,0.177 10 true *a 1.563,2.542 2.021,2.719 0.458,0.177 10 false G156 0.271,3.083 0.51,3.25 0.24,0.167 10 false SI0 2.938,2.99 3.25,3.156 0.313,0.167 10 false GND
*a Component with harness connected
(No. 2 EV Battery Pack Wire Connector)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-3 (SI0) - G156-1 (GND) Ignition switch ON 4.5 to 5.5 V


NOTICE:

Turning the ignition switch to ON with the service plug grip and FC converter power outlet cable removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Install the center No. 2 floor to brace extension.



OK

13.CHECK BATTERY COOLING BLOWER ASSEMBLY

NG

REPLACE BATTERY COOLING BLOWER ASSEMBLY

13.CHECK BATTERY COOLING BLOWER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs and freeze frame data.

Powertrain > EV Battery > Clear DTCs
50002 398

Procedure1

a.

Select each air volume mode (1 to 6) in the "Control the Hybrid/EV Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

Powertrain > EV Battery > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid/EV Battery Cooling Fan Battery cooling blower assembly operation and blower volume OFF, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > EV Battery > Active Test
Tester Display
Control the Hybrid/EV Battery Cooling Fan
50004 398 1
NOTICE:

If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the battery ECU assembly sends a command to operate the battery cooling blower assembly.



b.
C382282C16
1.51,2.427 1.948,2.677 0.438,0.25 2.51,3.5 2.938,3.188 true 2.104,3.5 0.583,3.135 true 0.083,0.083 0.344,0.281 0.26,0.198 10 true *a 1.563,2.458 2.052,2.646 0.49,0.188 10 false G156 2.969,3.073 3.344,3.26 0.375,0.188 10 false GND 0.208,3.052 0.583,3.24 0.375,0.188 10 false SI0
*a Component with harness connected
(No. 2 EV Battery Pack Wire Connector)


A284431C04
2.938,1.031 3.396,1.229 0.458,0.198 10 false GND 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a
*a Waveform 1


Connect an oscilloscope to the G156 No. 2 EV battery pack wire connector and check the waveform.

Item Content
Tester Connection G156-3 (SI0) - G156-1 (GND)
Equipment Setting 10 V/DIV., 1 ms./DIV.
Condition Ignition switch ON, during Active Test

NOTICE:

Turning the ignition switch to ON with the service plug grip and FC converter power outlet cable removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:
·

Perform this inspection with the No. 2 EV battery pack wire connector connected.

·

The wave length will vary with the operating speed of the battery cooling blower assembly.




Result:
Result Proceed to
Normal (The pulse output of waveform 1) A
No pulse generation B


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Install the center No. 2 floor to brace extension.



A

REPLACE BATTERY COOLING BLOWER ASSEMBLY

B

14.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
14.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374185C46
1.469,1.625 1.938,1.906 0.469,0.281 1.49,0.073 1.958,0.354 0.469,0.281 2.042,0.844 2.76,0.49 true 1.427,2.604 2.563,1.781 true 0.125,0.156 0.438,0.313 0.313,0.156 10 false *a 0.167,1.531 0.479,1.688 0.313,0.156 10 false *b 1.615,1.708 1.927,1.906 0.313,0.198 10 false z26 1.583,0.156 2.042,0.354 0.458,0.198 10 false G156 2.708,1.698 3.167,1.896 0.458,0.198 10 false SI0 2.844,0.427 3.302,0.625 0.458,0.198 10 false SI0
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,z26)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

G156-3 (SI0) - z26-33 (SI0) Always Below 1 Ω
G156-3 (SI0) or z26-33 (SI0) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

15.CHECK BATTERY ECU ASSEMBLY (GROUND SHORT CHECK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK BATTERY ECU ASSEMBLY (GROUND SHORT CHECK)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



b.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374184C11
1.469,1.823 1.896,2.083 0.427,0.26 0.771,1.844 1.375,2.771 true 0.906,1.521 1.635,2.646 true 1.667,2.813 1.906,3.167 true 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 1.594,1.885 1.906,2.083 0.313,0.198 10 false z26 0.5,1.698 0.958,1.896 0.458,0.198 10 false SI0 0.583,1.396 1.042,1.594 0.458,0.198 10 false GND 1.979,3.188 2.594,3.385 0.615,0.198 10 false GND1
*a Component without harness connected
(Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-33 (SI0) - z26-11 (GND) Always 10 kΩ or higher
z26-33 (SI0) - z26-31 (GND1) Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

16.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382284N03
2.635,1.406 3.042,1.604 0.406,0.198 2.677,1.417 3.01,1.583 0.333,0.167 10 true G31

Disconnect the G31 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C371974C19
1.573,0.219 1.948,0.438 0.375,0.219 1.948,1.677 2.583,1.375 true 0.115,0.156 0.427,0.313 0.313,0.156 10 false *a 2.698,1.24 3.156,1.438 0.458,0.198 10 false GND0 1.656,0.26 2.115,0.458 0.458,0.198 10 false G31
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G31)Location & Routing

Click Connector(G31)Body>Floor Wire / No. 3 Floor Wire>Battery Cooling Blower Assembly

G31-4 (GND0) - Body ground Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Connect the G31 battery cooling blower assembly connector.


b.

Install the center No. 2 floor to brace extension.



OK

17.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382281N05
2.688,0.25 3.146,0.479 0.458,0.229 2.74,0.281 3.115,0.448 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374188C20
1.531,0.24 1.969,0.469 0.438,0.229 0.677,1.802 1.208,1.406 true 0.677,0.646 1.177,1.125 true 0.25,0.573 0.865,0.771 0.615,0.198 10 false GND 0.26,1.781 0.875,1.979 0.615,0.198 10 false GND1 1.604,0.292 2.063,0.49 0.458,0.198 10 false G156 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-1 (GND) - Body ground Ignition switch off Below 1 Ω
G156-10 (GND1) - Body ground Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G156 No. 2 EV battery pack wire connector.


b.

Install the center No. 2 floor to brace extension.



OK

18.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATT FAN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATT FAN RELAY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382284N03
2.635,1.406 3.042,1.604 0.406,0.198 2.677,1.417 3.01,1.583 0.333,0.167 10 true G31

Disconnect the G31 battery cooling blower assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the BATT FAN relay and battery cooling blower assembly is not loose or disconnected.




d.

Remove the BATT FAN relay from the luggage room relay block assembly.

NOTICE:

Check the relay for deformation and corrosion.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A479023C01
4.99,0.708 5.396,0.927 0.406,0.219 4.708,1.198 5.104,1.427 true 0.448,0.083 0.76,0.281 0.313,0.198 10 false *1 1.969,1.948 2.281,2.146 0.313,0.198 10 false *b 4.646,0.177 4.958,0.375 0.313,0.198 10 false *a 4.458,1.083 4.917,1.281 0.458,0.198 10 false IG0 5.073,0.771 5.531,0.969 0.458,0.198 10 false G31
*1 Luggage Room Relay Block Assembly - -
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
*b BATT FAN Relay Holder


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G31)Location & Routing

Click Connector(G31)Body>Floor Wire / No. 3 Floor Wire>Battery Cooling Blower Assembly

G31-1 (IG0) - 5 (BATT FAN relay holder) Ignition switch off Below 1 Ω


NOTICE:
·

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

·

Make sure that each connector between the battery cooling blower assembly and BATT FAN relay holder is not loose or disconnected and its terminals are not deformed or corroded.




Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the BATT FAN relay to the luggage room relay block assembly.


b.

Reconnect the G31 battery cooling blower assembly connector.


c.

Install the center No. 2 floor to brace extension.



OK

19.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374183C22
1.469,0.531 1.885,0.802 0.417,0.271 1.625,1.469 0.76,0.802 true 1.656,1.76 2.625,2.542 true 0.115,0.135 0.427,0.292 0.313,0.156 10 false *a 0.406,0.708 0.865,0.906 0.458,0.198 10 false GND 2.802,2.51 3.26,2.708 0.458,0.198 10 false GND1 1.573,0.594 1.885,0.792 0.313,0.198 10 false z26
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-11 (GND) - Body ground Always Below 1 Ω
z26-31 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATT FAN FUSE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382284N03
2.635,1.406 3.042,1.604 0.406,0.198 2.677,1.417 3.01,1.583 0.333,0.167 10 true G31

Disconnect the G31 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Remove the BATT FAN fuse from the luggage room relay block assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A479520C01
4.927,0.615 5.448,0.875 0.521,0.26 4.583,1.156 5.104,1.438 true 0.448,0.76 0.76,0.958 0.313,0.198 10 false *1 1.49,0.458 1.802,0.656 0.313,0.198 10 false *b 4.542,0.167 4.854,0.365 0.313,0.198 10 false *a 5.063,0.688 5.375,0.885 0.313,0.198 10 false G31 4.333,1.031 4.646,1.229 0.313,0.198 10 false IG0
*1 Luggage Room Relay Block Assembly - -
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
*b BATT FAN Fuse Holder


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G31)Location & Routing

Click Connector(G31)Body>Floor Wire / No. 3 Floor Wire>Battery Cooling Blower Assembly

G31-1 (IG0) - Terminals other than 2 (BATT FAN fuse holder) and body ground Ignition switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the BATT FAN fuse to the luggage room relay block assembly.


b.

Reconnect the G31 battery cooling blower assembly connector.


c.

Install the center No. 2 floor to brace extension.



OK

21.CHECK BATTERY COOLING BLOWER ASSEMBLY

NG

23.REPAIR OR REPLACE HARNESS OR CONNECTOR
21.CHECK BATTERY COOLING BLOWER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382284N03
2.635,1.406 3.042,1.604 0.406,0.198 2.677,1.417 3.01,1.583 0.333,0.167 10 true G31

Disconnect the G31 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C373306C07
1.521,0.198 1.917,0.469 0.396,0.271 0.792,0.917 1.552,1.469 true 1.896,1.25 2.49,0.76 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.615,0.26 2.073,0.458 0.458,0.198 10 false G31 2.583,0.625 3.042,0.823 0.458,0.198 10 false IG0 0.448,0.75 0.906,0.948 0.458,0.198 10 false GND0
*a Component without harness connected
(Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G31)Location & Routing

Click Connector(G31)Body>Floor Wire / No. 3 Floor Wire>Battery Cooling Blower Assembly

G31-1 (IG0) - G31-4 (GND0) and Body ground Always 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G31 battery cooling blower assembly connector.


b.

Install the center No. 2 floor to brace extension.



OK

REPLACE FUSE (BATT FAN)

NG

22.REPLACE BATTERY COOLING BLOWER ASSEMBLY
22.REPLACE BATTERY COOLING BLOWER ASSEMBLY

NEXT

REPLACE FUSE (BATT FAN)

23.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (BATT FAN)