The tension sensor is built into the parking brake actuator assembly with bracket. It detects the tension value of the parking brake cable and outputs the value to the No. 2 skid control ECU (brake actuator assembly).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| C112512 | Electric Parking Brake Tension Sensor "B" Circuit Short to Battery | ·
Diagnosis Condition: Electric parking brake switch assembly is operated to lock side with ignition switch off or ignition switch ON ·
Malfunction Status: Tension2 Voltage voltage is 4.5 V or more ·
Malfunction Duration: Approximately 1 second |
·
Parking brake actuator assembly with bracket ·
Wire harness or connector ·
No. 2 skid control ECU (brake actuator assembly) |
DTC stored | Brake/EPB | A | An electric parking brake system malfunction is displayed on the multi-information display. |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Electric parking brake switch assembly is operated to lock side with ignition switch off | ○ | - |
| Ignition switch ON | - | ○ | |
| Malfunction Status | Tension2 Voltage voltage is 4.5 V or more | ○ | ○ |
| Detection Time | Approximately 1 second | Approximately 1 second | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "EPB Initialize" and "Acquire Tension Sensor Zero Point".
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY
After replacing the parking brake actuator assembly with bracket, perform "EPB Initialize" and "Acquire Tension Sensor Zero Point".
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY
Pre-procedure1
Turn the ignition switch off.
Disconnect the G71 parking brake actuator assembly with bracket connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G71)Location & Routingewd_type=routing;type=c;code=G71 Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assemblyewd_type=component;type=c;code=G71;pinno=10,1 |
||
| G71-10 (TSN2) - G71-1 (TGND) | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Disconnect the G71 parking brake actuator assembly with bracket connector.
Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G71,A6)Location & Routingewd_type=routing;type=c,c;code=G71,A6 Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assemblyewd_type=component;type=c;code=G71;pinno=10,1 |
||
| G71-10 (TSN2) or A6-40 (TSN2) - Body ground | Ignition switch ON | Below 1 V |
| G71-1 (TGND) or A6-42 (TGND) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
NG