Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
RM37H0E _54 Brake _096946 PARKING BRAKE _0455727 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C112A62  Electric Parking Brake Tension Sensor "A/B" Correlation Signal Compare Failure  


DESCRIPTION

The tension sensor is built into the parking brake actuator assembly with bracket. It detects the tension value of the parking brake cable and outputs the value to the No. 2 skid control ECU (brake actuator assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C112A62 Electric Parking Brake Tension Sensor "A/B" Correlation Signal Compare Failure
·

Diagnosis Condition:

Electric parking brake switch assembly is operated to lock side with ignition switch off or ignition switch ON

·

Malfunction Status:

A n excessive voltage difference exists between the tension1 voltage value and tension2 voltage value

·

Malfunction Duration:

Approximately 1 second


·

Parking brake actuator assembly with bracket

·

Wire harness or connector

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored Brake/EPB A An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Electric parking brake switch assembly is operated to lock side with ignition switch off ○ -
Ignition switch ON - ○
Malfunction Status A n excessive voltage difference exists between the tension1 voltage value and tension2 voltage value ○ ○
Detection Time Approximately 1 second Approximately 1 second
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C446912E03
0.115,3.177 3.542,3.51 3.427,0.333 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 0.104,2.948 0.49,3.146 0.385,0.198 10 false A6 4.552,3.198 6.656,3.594 2.104,0.396 10 false Parking Brake Actuator Assembly with Bracket 4.49,2.979 4.792,3.167 0.302,0.188 10 false G71 2.177,1.896 2.594,2.135 0.417,0.24 10 false TGND 5.042,2.031 5.458,2.271 0.417,0.24 10 false TGND 2.167,2.615 2.583,2.854 0.417,0.24 10 false GND1 2.688,2.646 2.896,2.865 0.208,0.219 10 false 1 2.677,1.885 3.094,2.125 0.417,0.24 10 false 42 2.198,1.042 2.615,1.281 0.417,0.24 10 false TSN2 5.052,1.156 5.469,1.396 0.417,0.24 10 false TSN2 2.198,0.208 2.615,0.448 0.417,0.24 10 false TSEN 5.031,0.333 5.448,0.573 0.417,0.24 10 false TSEN 4.823,0.208 4.99,0.406 0.167,0.198 10 false 5 4.771,1.021 4.99,1.271 0.219,0.25 10 false 10 4.844,1.917 5.063,2.167 0.219,0.25 10 false 1 2.698,0.208 2.865,0.406 0.167,0.198 10 false 8 2.667,1.021 3.021,1.281 0.354,0.26 10 false 40 0.844,0.344 1.135,0.573 0.292,0.229 10 false IC 0.844,1.177 1.135,1.406 0.292,0.229 10 false IC 0.896,2.01 1.26,2.24 0.365,0.229 10 false IG

CAUTION / NOTICE / HINT

NOTICE:
·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "EPB Initialize" and "Acquire Tension Sensor Zero Point".

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY

·

After replacing the parking brake actuator assembly with bracket, perform "EPB Initialize" and "Acquire Tension Sensor Zero Point".

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G71 parking brake actuator assembly with bracket connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6,G71)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assembly

A6-8 (TSEN) - G71-5 (TSEN) Always Below 1 Ω
A6-40 (TSN2) - G71-10 (TSN2) Always Below 1 Ω
A6-42 (TGND) - G71-1 (TGND) Always Below 1 Ω
A6-8 (TSEN) or G71-5 (TSEN) - Body ground Always 10 kΩ or higher
A6-40 (TSN2) or G71-10 (TSN2) - Body ground Always 10 kΩ or higher
A6-42 (TGND) or G71-1 (TGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET (TENSION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET (TENSION SENSOR)

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.
C445925C20
0.146,0.813 0.594,1.094 0.448,0.281 2.333,1.01 2.688,0.26 2.688,0.26 2.854,0.26 true 2.333,1.333 2.708,1.927 2.708,1.927 2.875,1.927 true 0.469,1.917 0.635,1.917 0.635,1.917 1.083,1.333 true 0.24,0.885 0.573,1.094 0.333,0.208 10 false G71 2.938,1.865 3.354,2.094 0.417,0.229 10 false TSEN 2.906,0.208 3.333,0.51 0.427,0.302 10 false TGND 0.094,1.854 0.51,2.083 0.417,0.229 10 false TSN2 0.188,0.125 0.521,0.333 0.333,0.208 10 false *a
*a Component with harness connected
(Parking Brake Actuator Assembly with Bracket)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G71)Location & Routing

Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assembly

G71-1 (TGND) - G71-5 (TSEN) Ignition switch ON 0.35 to 4.5 V
G71-1 (TGND) - G71-10 (TSN2) Ignition switch ON 0.35 to 4.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET