Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
RM37H0E _54 Brake _096946 PARKING BRAKE _0455727 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C112B12  Electric Parking Brake Tension Sensor Supply Voltage Circuit Short to Battery  


DESCRIPTION

The tension sensor is built into the parking brake actuator assembly with bracket. It detects the tension value of the parking brake cable and outputs the value to the No. 2 skid control ECU (brake actuator assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C112B12 Electric Parking Brake Tension Sensor Supply Voltage Circuit Short to Battery
·

Diagnosis Condition:

Electric parking brake switch assembly is operated to lock side with ignition switch off or ignition switch ON

·

Malfunction Status:

Tension Sensor Voltage voltage is 5.5 V or more

·

Malfunction Duration:

Approximately 1 second


·

Parking brake actuator assembly with bracket

·

Wire harness or connector

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored Brake/EPB A An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Electric parking brake switch assembly is operated to lock side with ignition switch off ○ -
Ignition switch ON - ○
Malfunction Status Tension Sensor Voltage voltage is 5.5 V or more ○ ○
Detection Time Approximately 1 second Approximately 1 second
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C446911E03
0.813,2.979 3.427,3.5 2.615,0.521 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 0.51,2.969 0.906,3.188 0.396,0.219 10 false A6 1.115,1.073 1.354,1.323 0.24,0.25 10 false IC 1.146,1.823 1.385,2.073 0.24,0.25 10 false IG 2.427,2.427 2.833,2.646 0.406,0.219 10 false GND1 2.469,1.646 2.885,1.875 0.417,0.229 10 false TGND 2.615,0.938 2.896,1.125 0.281,0.188 10 false VT 2.927,1.635 3.344,1.865 0.417,0.229 10 false 42 2.958,2.438 3.177,2.656 0.219,0.219 10 false 1 2.938,0.917 3.219,1.146 0.281,0.229 10 false 23 5.323,1.042 5.604,1.229 0.281,0.188 10 false VT 5.094,1.625 5.313,1.844 0.219,0.219 10 false 1 5.333,1.781 5.75,2.01 0.417,0.229 10 false TGND 5.063,0.917 5.479,1.146 0.417,0.229 10 false 6 4.813,3.031 6.927,3.365 2.115,0.333 10 false Parking Brake Actuator Assembly with Bracket 4.792,2.813 5.156,3.031 0.365,0.219 10 false G71

CAUTION / NOTICE / HINT

NOTICE:
·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "EPB Initialize" and "Acquire Tension Sensor Zero Point".

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY

·

After replacing the parking brake actuator assembly with bracket, perform "EPB Initialize" and "Acquire Tension Sensor Zero Point".

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK FOR SHORT TO +B

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-23 (VT) - A6-42 (TGND) Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

2.CHECK FOR SHORT TO +B
2.CHECK FOR SHORT TO +B

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the G71 parking brake actuator assembly with bracket connector.


c.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G71,A6)Location & Routing

Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assembly

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

G71-6 (VT) or A6-23 (VT) - Body ground Ignition switch ON Below 1 V
G71-1 (TGND) or A6-42 (TGND) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR