Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
RM37H0E _54 Brake _096946 PARKING BRAKE _0455727 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C113011  Unified Electric Parking Brake Actuator Control Circuit Short to Ground  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C113011 Unified Electric Parking Brake Actuator Control Circuit Short to Ground
·

Diagnosis Condition:

Electric parking brake not operating

·

Malfunction Status:

The ECU power supply is normal but there is a malfunction in the parking brake actuator assembly with bracket internal circuit (short to GND).

·

Detection Time:

Approximately 1 second (depending on each malfunction)


·

Parking brake actuator assembly with bracket

·

Wire harness or connector

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored Brake/EPB A An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

C448914E03
0.75,2 1.365,2.198 0.615,0.198 10 false A6 2.448,0.469 2.604,0.667 0.156,0.198 10 false 2 2.448,1.188 2.604,1.385 0.156,0.198 10 false 3 4.594,0.469 4.719,0.677 0.125,0.208 10 false 7 4.594,1.198 4.781,1.365 0.188,0.167 10 false 8 4.833,0.573 5.188,0.771 0.354,0.198 10 false M- 0.75,2.167 2.677,2.635 1.927,0.469 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 4.281,2.135 6.396,2.521 2.115,0.385 10 false Parking Brake Actuator Assembly with Bracket 4.292,1.938 4.906,2.135 0.615,0.198 10 false G71 4.833,1.323 5.188,1.521 0.354,0.198 10 false M+ 2.094,0.563 2.448,0.76 0.354,0.198 10 false M- 2.083,1.313 2.438,1.51 0.354,0.198 10 false M+

CAUTION / NOTICE / HINT

NOTICE:
·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "EPB Initialize" and "Acquire Tension Sensor Zero Point".

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G71 parking brake actuator assembly with bracket connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6,G71)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assembly

A6-3 (M+) - G71-8 (M+) Always Below 1 Ω
A6-2 (M-) - G71-7 (M-) Always Below 1 Ω
A6-3 (M+) or G71-8 (M+) - Body ground Always 10 kΩ or higher
A6-2 (M-) or G71-7 (M-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET (PARKING BRAKE MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET (PARKING BRAKE MOTOR)

Pre-procedure1

a.

Turn the ignition switch off.


b.
C139753C09
1.552,0.177 1.927,0.427 0.375,0.25 0.333,1.667 0.333,1.583 0.333,1.583 1.5,1.333 true 2,1.333 3,1.583 3,1.583 3,1.667 true 2.917,1.708 3.24,1.917 0.323,0.208 10 false M+ 0.271,1.719 0.583,1.917 0.313,0.198 10 false M- 0.125,0.146 0.417,0.375 0.292,0.229 10 false *a 1.615,0.229 1.927,0.427 0.313,0.198 10 false G71
*a Component without harness connected
(Parking Brake Actuator Assembly with Bracket)


Disconnect the G71 parking brake actuator assembly with bracket connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G71)Location & Routing

Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assembly

G71-7(M-) - G71-8(M+) Always Below 4 Ω
G71-7 (M-) - Body ground Always 10 kΩ or higher
G71-8 (M+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET