Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
RM37H0E _54 Brake _096946 PARKING BRAKE _0455727 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13B896  Electric Parking Brake Actuator Component Internal Failure  


DESCRIPTION

The tension sensor is built into the parking brake actuator assembly with bracket. It detects the tension value of the parking brake cable and outputs the value to the No. 2 skid control ECU (brake actuator assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C13B896 Electric Parking Brake Actuator Component Internal Failure
·

Diagnosis Condition:

Electric parking brake switch assembly is operated to lock side with ignition switch off or ignition switch ON

·

Malfunction Status:

The voltage of the tension sensor 1 zero point correction value or tension sensor 2 zero point correction value is abnormal

·

Malfunction Duration:

The malfunction status repeats 3 times


·

Parking brake actuator assembly with bracket

·

Wire harness or connector

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored Brake/EPB A An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Electric parking brake switch assembly is operated to lock side with ignition switch off ○ -
Ignition switch ON - ○
Malfunction Status The voltage of the tension sensor 1 zero point correction value or tension sensor 2 zero point correction value is abnormal ○ ○
Detection Time Repeats 3 times Repeats 3 times
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "EPB Initialize" and "Acquire Tension Sensor Zero Point".

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G71 parking brake actuator assembly with bracket connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6,G71)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assembly

A6-8 (TSEN) - G71-5 (TSEN) Always Below 1 Ω
A6-40 (TSN2) - G71-10 (TSN2) Always Below 1 Ω
A6-42 (TGND) - G71-1 (TGND) Always Below 1 Ω
A6-8 (TSEN) or G71-5 (TSEN) - Body ground Always 10 kΩ or higher
A6-40 (TSN2) or G71-10 (TSN2) - Body ground Always 10 kΩ or higher
A6-42 (TGND) or G71-1 (TGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.READ VALUE USING GTS (INVALID TENSION SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING GTS (INVALID TENSION SENSOR OUTPUT)
a.

Check the values by referring to the table below.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Invalid Tension Sensor Output Tension sensor output invalid display Enable / Disable Enable -
Chassis > Brake/EPB > Data List
Tester Display
Invalid Tension Sensor Output
50003 435 339
Result:
Result Proceed to
The value of Invalid Tension Sensor Output is Enable A
The value of Invalid Tension Sensor Output is Disable B




A

3.READ VALUE USING GTS (INVALID TENSION SENSOR PWR)

B

3.READ VALUE USING GTS (INVALID TENSION SENSOR PWR)
a.

Check the values by referring to the table below.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Invalid Tension Sensor PWR Tension sensor power source invalid display Enable / Disable Enable -
Chassis > Brake/EPB > Data List
Tester Display
Invalid Tension Sensor PWR
50003 435 340
Result:
Result Proceed to
The value of Invalid Tension Sensor PWR is Enable A
The value of Invalid Tension Sensor PWR is Disable B




A

4.READ VALUE USING GTS (INVALID TENSION SENSOR COMP)

B

4.READ VALUE USING GTS (INVALID TENSION SENSOR COMP)
a.

Check the values by referring to the table below.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Invalid Tension Sensor Comp Tension sensor comparison invalid display Enable / Disable Enable -
Chassis > Brake/EPB > Data List
Tester Display
Invalid Tension Sensor Comp
50003 435 341
Result:
Result Proceed to
The value of Invalid Tension Sensor Comp is Enable A
The value of Invalid Tension Sensor Comp is Disable B




A

5.CLEAR DTC

B

5.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT




NEXT

6.CHECK DTC
6.CHECK DTC
a.

Check for DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
DTCs are output A
DTCs are not output B




A

B