Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A0812  DC/DC Converter Status Circuit Short to Battery  


DESCRIPTION

The DC/DC converter varies output voltage based on voltage change signals (VLO signal line) received from the EV control ECU.

If the vehicle is being driven with an inoperative DC/DC converter, the voltage of the auxiliary battery will drop, which will prevent the continued operation of the vehicle. Therefore, the EV control ECU monitors the operation of the DC/DC converter and alerts the driver if it detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0A0812 DC/DC Converter Status Circuit Short to Battery Short to +B in the DC/DC converter VLO signal line
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

EV control ECU


Master Warning:
Comes on
EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 10 seconds or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A479447E01
0.458,1.854 3.208,2.052 2.75,0.198 10 false Inverter with Converter Assembly 4.823,2.823 5.281,3.021 0.458,0.198 10 false A17 4.719,1 5.177,1.198 0.458,0.198 10 false VLO 1.74,0.99 2.198,1.188 0.458,0.198 10 false VLO 2.156,1.01 2.313,1.208 0.156,0.198 10 false 6 4.448,1 4.76,1.198 0.313,0.198 10 false 17 4.479,2.438 4.635,2.635 0.156,0.198 10 false 4 4.833,2.979 6.563,3.167 1.729,0.188 10 false EV Control ECU 0.479,1.688 0.938,1.885 0.458,0.198 10 false A20 4.708,2.427 5.021,2.625 0.313,0.198 10 false E1 5.552,1.698 6.01,1.896 0.458,0.198 10 false ADC 1.281,0.51 1.594,0.708 0.313,0.198 10 false +B

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK EV CONTROL ECU (CHECK WAVEFORM)

Pre-procedure1

a.

Connect an oscilloscope between the EV control ECU terminals specified in the table below.


b.

Turn the ignition switch to ON.


Procedure1

a.
A479448C03
2.042,0.396 2.448,0.688 0.406,0.292 2.719,1.833 2.531,1.323 true 2.063,1.813 2.271,1.188 true 0.115,0.135 0.427,0.292 0.313,0.156 10 false *a 2.135,0.479 2.448,0.635 0.313,0.156 10 false A17 2.646,1.854 2.958,2.01 0.313,0.156 10 false VLO 1.969,1.854 2.281,2.01 0.313,0.156 10 false E1 2.792,3.344 3.229,3.583 0.438,0.24 10 false GND
*a Component with harness connected
(EV Control ECU)


Measure the waveform.

Tester Connection Condition Equipment Setting

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-17 (VLO) - A17-4 (E1) Ignition switch ON 5 V/DIV., 50 ms./DIV.

OK:

The waveform appears as shown in the illustration.


HINT:
·

Perform this inspection with the EV control ECU connector connected.

·

The waveform (duty ratio) differs depending on the command value from the EV control ECU.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

2.CLEAR DTC

NG

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - EV CONTROL ECU)
2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (EV)
3.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P0A0812 is not output A
P0A0812 is output B



Post-procedure1

a.

Turn the ignition switch off.



A

B

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - EV CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A20 inverter with converter assembly connector.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL



c.

Disconnect the A17 EV control ECU connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.
A479449C05
1.51,0.198 1.906,0.51 0.396,0.313 2.042,2.083 2.438,2.396 0.396,0.313 2.229,1.688 1.792,1.177 true 2.781,4.292 2.51,3.927 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.083,2 0.396,2.156 0.313,0.156 10 false *b 2.135,2.188 2.594,2.385 0.458,0.198 10 false A17 1.604,0.281 2.063,0.479 0.458,0.198 10 false A20 2.271,1.75 2.729,1.948 0.458,0.198 10 false VLO 2.792,4.344 3.25,4.542 0.458,0.198 10 false VLO
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A20,A17)Location & Routing

Click Connector(A20)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A20-6 (VLO) or A17-17 (VLO) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the inverter with converter assembly connector and the EV control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the A17 EV control ECU connector.


d.

Reconnect the A20 inverter with converter assembly connector.



OK

5.REPLACE EV CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE EV CONTROL ECU

NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK DTC OUTPUT (EV)
7.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P0A0812 is not output A
P0A0812 is output B



Post-procedure1

a.

Turn the ignition switch off.



A

COMPLETED

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY