Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C2D62  Hybrid/EV Battery "A" Voltage Sensor/Boosting Converter Voltage Sensor "A" Signal Compare Failure  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU detects a VB sensor or VL sensor malfunction.

The cause of this malfunction may be one of the following:

Inverter voltage (VB or VL) sensor internal circuit malfunction
·

Voltage sensor malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

EV supply battery assembly malfunction

·

No. 1 EV battery junction block assembly malfunction

·

Inverter with converter assembly malfunction

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction

·

FC converter assembly malfunction



Inspection Overview


Inspection Content Reason (Narrow Down in Order Using Inspection Procedures Below)
Check for DTCs (EV) Output DTCs
Check for DTCs (check voltage sensor malfunction locations)
Check for DTCs (drive test)
Put vehicle in ready ON (vehicle stopped and being driven) and then check whether DTCs are output again.
Read value using GTS Data List value
Check freeze frame data (EV) FREEZE FRAME DATA
Read value using GTS Accelerator and brake pedal simultaneously depressed Data List value


DESCRIPTION

Refer to the description for DTC P0CA300.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0CA300

The MG ECU uses a voltage sensor (VL) that is built into the boost converter to detect the high voltage before it is boosted. The ECU also uses the battery ECU assembly to detect EV battery voltage (VB).

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1C2D62 Hybrid/EV Battery "A" Voltage Sensor/Boosting Converter Voltage Sensor "A" Signal Compare Failure Voltages from EV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate:
Difference between "VL-Voltage before Boosting" and "Hybrid/EV Battery Voltage" is large when the boosting request is given.
(1 trip detection logic)
·

Inverter with converter assembly

·

Battery ECU assembly


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P1C2D62
·

Hybrid/EV Battery Voltage

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Boost Ratio



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY).

4.

Push the P position switch (shift position indicator) to select park (P), depress the accelerator pedal to raise the "Hybrid/EV Battery SOC" to a sufficient level.

5.

Check that the FC system is stopped and move the shift lever to select shift state neutral (N).

6.

Set the A/C for maximum cooling.

7.

Leave the vehicle for a few minutes.

HINT:

When the accelerator pedal is not depressed with the ignition switch ON (READY) and park (P) selected, if "VL-Voltage before Boosting" and the "Hybrid/EV Battery Voltage" is approximately the same after repair, the condition is judged as normal.


8.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV, EV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > EV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
One of the following applies:
·

Only P1C2D62 is output.

·

One or more DTCs other than P0E311C, P0CA300, P0B231C, and DTCs in the table below are also output.


A
P1C2D62 and P0E311C or P0CA300 are output at the same time. B
P1C2D62 and P0B231C are output at the same time. C
DTCs of hybrid control system in the tables below are output. D
DTCs of hybrid battery system in the tables below are output. E


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P1C8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B16 Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Power source circuit malfunction Hybrid control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
P06E61C Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message
Sensor and actuator circuit malfunction Hybrid battery system P301A1C Hybrid/EV Battery Stack 1 Cell Voltage Detection Voltage Out of Range
P1A001C Hybrid/EV Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P1AFD1C Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range
System malfunction Hybrid control system P0E3116 DC/DC Converter Voltage Sensor "A" Circuit Voltage Below Threshold
P0E3117 DC/DC Converter Voltage Sensor "A" Circuit Voltage Above Threshold

HINT:
·

P1C2D62 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CLEAR DTC

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

D

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

E

2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (CHECK FAILURE PART)
3.CHECK DTC OUTPUT (CHECK FAILURE PART)

Pre-procedure1

a.

Apply the parking brake and secure the wheels using chocks.


b.

Connect the GTS to the DLC3. *1


c.

Turn the ignition switch to ON (READY). *2


d.

Enter the following menus: Powertrain / EV / Data List. *3

Powertrain > EV > Data List
Tester Display
Hybrid/EV Battery SOC
50003 397 320

e.

Push the P position switch (shift position indicator) to select park (P). *4


f.

If the value of "Hybrid/EV Battery SOC" is less than 55%, charge the EV battery by depressing the accelerator pedal until the value reaches 55% or more. *5


g.

Set the air conditioning to MAX COOL and turn the headlights on. *6


h.

Confirm that "Hybrid/EV Battery Current" is more than 3 A. *7

Powertrain > EV > Data List
Tester Display
Hybrid/EV Battery Current
50003 397 228

i.

With the FC system stopped and the conditions of steps *5, *6 and *7 satisfied, leave the vehicle for 15 seconds. *8


j.

Enter the following menus: Powertrain / EV, EV battery / Trouble codes. *9


Procedure1

a.

Check for DTCs. *10

Powertrain > EV > Trouble Codes
50001 397
Powertrain > EV Battery > Trouble Codes
50001 398
NOTICE:

If the low EV supply battery assembly information comes on, push the P position switch (shift position indicator) to select park (P) and start the engine to charge the EV supply battery assembly. After the engine stops, perform steps *1 through *10 again.


Result:
Result Proceed to
No DTCs are output, or DTCs except the following are output A
P0E311C or P0CA300 are output B
P0B231C or P1C8349 are output C
P300000 is output D
None of the above conditions are met E



Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK FREEZE FRAME DATA (EV)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

D

LEAVE VEHICLE WITH PARK (P) SELECTED, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS *1 THROUGH *10)

E

4.CHECK FREEZE FRAME DATA (EV)
4.CHECK FREEZE FRAME DATA (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P1C2D62.

Powertrain > EV
Tester Display Measurement Item Range
VL-Voltage before Boosting High voltage before it is boosted -
Hybrid/EV Battery Voltage EV supply battery voltage Min.: 0.0 V, Max.: 510.0 V
Powertrain > EV > DTC(P1C2D62) > Freeze Frame Data
Tester Display
VL-Voltage before Boosting
Hybrid/EV Battery Voltage
50040 397 150,227 P1C2D62
Result:
Result Proceed to
Both of the following are satisfied or both of the following are not satisfied A
The value of VL-Voltage before Boosting is more than 351 V, or less than 227 V B
The value of Hybrid/EV Battery Voltage is more than 351 V, or less than 227 V C



Post-procedure1

a.

Turn the ignition switch off.



A

5.READ VALUE USING GTS (DATA LIST)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

5.READ VALUE USING GTS (DATA LIST)

Pre-procedure1

a.

Apply the parking brake and secure the wheels using chocks.


b.

Turn the ignition switch to ON (READY).


Procedure1

a.

Push the P position switch (shift position indicator) to select park (P).


b.

If the value of "Hybrid Battery SOC" is less than 55%, charge the EV supply battery assembly by depressing the accelerator pedal until the value reaches 55% or more.

Powertrain > EV Battery > Data List
Tester Display
Hybrid/EV Battery SOC
50003 398 297

c.

Release the accelerator pedal, and wait for the FC system to stop. Read the Data List when the FC system stops.

HINT:

If the FC system starts, wait until it stops before continuing.


Powertrain > EV Battery > Data List
Tester Display
Hybrid/EV Battery Voltage
Hybrid/EV Battery Cell 1 Voltage
Hybrid/EV Battery Cell 2 Voltage
Hybrid/EV Battery Cell 3 Voltage
Hybrid/EV Battery Cell 4 Voltage
Hybrid/EV Battery Cell 5 Voltage
Hybrid/EV Battery Cell 6 Voltage
Hybrid/EV Battery Cell 7 Voltage
Hybrid/EV Battery Cell 8 Voltage
Hybrid/EV Battery Cell 9 Voltage
Hybrid/EV Battery Cell 10 Voltage
Hybrid/EV Battery Cell 11 Voltage
Hybrid/EV Battery Cell 12 Voltage
Hybrid/EV Battery Cell 13 Voltage
Hybrid/EV Battery Cell 14 Voltage
Hybrid/EV Battery Cell 15 Voltage
Hybrid/EV Battery Cell 16 Voltage
Hybrid/EV Battery Cell 17 Voltage
Hybrid/EV Battery Cell 18 Voltage
Hybrid/EV Battery Cell 19 Voltage
Hybrid/EV Battery Cell 20 Voltage
Hybrid/EV Battery Cell 21 Voltage
Hybrid/EV Battery Cell 22 Voltage
Hybrid/EV Battery Cell 23 Voltage
Hybrid/EV Battery Cell 24 Voltage
Hybrid/EV Battery Cell 25 Voltage
Hybrid/EV Battery Cell 26 Voltage
Hybrid/EV Battery Cell 27 Voltage
Hybrid/EV Battery Cell 28 Voltage
Hybrid/EV Battery Cell 29 Voltage
Hybrid/EV Battery Cell 30 Voltage
Hybrid/EV Battery Cell 31 Voltage
Hybrid/EV Battery Cell 32 Voltage
Hybrid/EV Battery Cell 33 Voltage
Hybrid/EV Battery Cell 34 Voltage
Hybrid/EV Battery Cell 35 Voltage
Hybrid/EV Battery Cell 36 Voltage
Hybrid/EV Battery Cell 37 Voltage
Hybrid/EV Battery Cell 38 Voltage
Hybrid/EV Battery Cell 39 Voltage
Hybrid/EV Battery Cell 40 Voltage
Hybrid/EV Battery Cell 41 Voltage
Hybrid/EV Battery Cell 42 Voltage
Hybrid/EV Battery Cell 43 Voltage
Hybrid/EV Battery Cell 44 Voltage
Hybrid/EV Battery Cell 45 Voltage
Hybrid/EV Battery Cell 46 Voltage
Hybrid/EV Battery Cell 47 Voltage
Hybrid/EV Battery Cell 48 Voltage
Hybrid/EV Battery Cell 49 Voltage
Hybrid/EV Battery Cell 50 Voltage
Hybrid/EV Battery Cell 51 Voltage
Hybrid/EV Battery Cell 52 Voltage
Hybrid/EV Battery Cell 53 Voltage
Hybrid/EV Battery Cell 54 Voltage
Hybrid/EV Battery Cell 55 Voltage
Hybrid/EV Battery Cell 56 Voltage
Hybrid/EV Battery Cell 57 Voltage
Hybrid/EV Battery Cell 58 Voltage
Hybrid/EV Battery Cell 59 Voltage
Hybrid/EV Battery Cell 60 Voltage
Hybrid/EV Battery Cell 61 Voltage
Hybrid/EV Battery Cell 62 Voltage
Hybrid/EV Battery Cell 63 Voltage
Hybrid/EV Battery Cell 64 Voltage
Hybrid/EV Battery Cell 65 Voltage
Hybrid/EV Battery Cell 66 Voltage
Hybrid/EV Battery Cell 67 Voltage
Hybrid/EV Battery Cell 68 Voltage
Hybrid/EV Battery Cell 69 Voltage
Hybrid/EV Battery Cell 70 Voltage
Hybrid/EV Battery Cell 71 Voltage
Hybrid/EV Battery Cell 72 Voltage
Hybrid/EV Battery Cell 73 Voltage
Hybrid/EV Battery Cell 74 Voltage
Hybrid/EV Battery Cell 75 Voltage
Hybrid/EV Battery Cell 76 Voltage
Hybrid/EV Battery Cell 77 Voltage
Hybrid/EV Battery Cell 78 Voltage
Hybrid/EV Battery Cell 79 Voltage
Hybrid/EV Battery Cell 80 Voltage
Hybrid/EV Battery Cell 81 Voltage
Hybrid/EV Battery Cell 82 Voltage
Hybrid/EV Battery Cell 83 Voltage
Hybrid/EV Battery Cell 84 Voltage
50003 398 288,334,335,336,337,338,339,340,341,342,343,344,345,346,347,348,349,350,351,352,353,354,355,356,357,358,359,360,361,362,363,364,365,366,367,368,369,370,371,372,373,374,375,376,377,378,379,380,381,382,383,384,385,386,387,388,389,390,391,392,393,394,395,396,397,398,399,400,401,402,403,404,405,406,407,408,409,410,411,412,413,414,415,416,417
Result:
Result Proceed to
Both of the following are satisfied:
·

Sum of all "Hybrid/EV Battery Cell 1 to 84 Voltage" is more than ("Hybrid/EV Battery Voltage" -5 V)

·

Sum of all "Hybrid/EV Battery Cell 1 to 84 Voltage" is less than ("Hybrid/EV Battery Voltage" -5 V)


A
The preceding condition is not satisfied. B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B