Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1D7A1C  FC Air Compressor Motor Temperature Sensor Circuit Voltage Out of Range  P1D7A1F  FC Air Compressor Motor Temperature Sensor Circuit Intermittent  


DESCRIPTION

The resistance of the thermistor built into the FC air compressor motor temperature sensor changes in accordance with changes in FC air compressor motor temperature. The lower the FC air compressor motor temperature, the higher the thermistor resistance. Conversely, the higher the FC air compressor motor temperature, the lower the resistance.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D7A1C FC Air Compressor Motor Temperature Sensor Circuit Voltage Out of Range FC air compressor motor temperature sensor output does not increase in which the value should increase, or output does not decrease under conditions in which the value should decrease.
(1 trip detection logic)
FC air compressor with motor assembly (FC air compressor motor temperature sensor) Master Warning:
Comes on
EV A
P1D7A1F FC Air Compressor Motor Temperature Sensor Circuit Intermittent Sudden change in FC air compressor motor temperature sensor output or hunting:
Unusual sudden change in FC air compressor motor temperature sensor output occurs and offset condition continues for a certain period of time, or unusual change in motor temperature sensor output occurs repeatedly.
(1 trip detection logic)
FC air compressor with motor assembly (FC air compressor motor temperature sensor) Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P1D7A1C FC Air Compressor Motor Temperature
P1D7A1F

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


·

If DTC P1D7A1C is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Drive the vehicle (stop and go driving) on urban roads for approximately 5 minutes. If the Data List item "FC Air Compressor Motor Temperature" shows both increases and decreases in temperature, suspected areas indicated by this DTC are not malfunctioning.

(b)

Enter the following menus: Powertrain / EV / Utility / All Readiness.

(c)

Check the DTC judgment result.

HINT:

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.



·

If DTC P1D7A1F is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

(b)

Drive the vehicle for approximately 5 minutes according to the freeze frame data items "Vehicle Speed", "Inverter Coolant Water Temperature", "Motor Temperature" and "FC Air Compressor Motor Temperature".

(c)

Enter the following menus: Powertrain / EV / Utility / All Readiness.

(d)

Check the DTC judgment result.

HINT:

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.




CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (FC CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1F089F

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK HARNESS AND CONNECTOR (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY - FC CONTROL ECU)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY - FC CONTROL ECU)

Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A481477C02
1.604,0.073 2.042,0.417 0.438,0.344 1.146,1.802 0.938,1.292 true 0.615,1.823 0.833,1.313 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.448,1.854 0.906,2.052 0.458,0.198 10 false AMT 1,1.844 1.427,2.042 0.427,0.198 10 false GAMT 1.771,0.177 2.083,0.375 0.313,0.198 10 false B1
*a Front view of wire harness connector
(to FC Control ECU)


Disconnect the B1 FC control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

B1-110 (AMT) - B1-111 (AMTG) Ignition switch off 1.393 to 75.8 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B1 FC control ECU connector.



OK

3.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)

NG

7.CHECK HARNESS AND CONNECTOR
3.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A481468

Check the connector connections and contact pressure of the relevant terminals for the stack wire connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



Post-procedure1

a.

None.



A

4.CHECK HARNESS AND CONNECTOR (STACK WIRE - FC CONTROL ECU)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (STACK WIRE - FC CONTROL ECU)

Pre-procedure1

a.
A481468

Disconnect the BB1 stack wire connector.


b.

Disconnect the B1 FC control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A481498C01
0.438,0.792 0.885,1.125 0.448,0.333 3.531,0.771 3.969,1.073 0.438,0.302 4.49,1.125 4.146,1.531 true 4.563,1.135 4.927,1.531 true 1.948,0.99 1.625,1.542 true 2.063,0.99 2.427,1.531 true 0.542,0.875 1,1.073 0.458,0.198 10 false BB1 3.688,0.844 4,1.042 0.313,0.198 10 false B1 3.99,1.563 4.438,1.708 0.448,0.146 10 false AMT 4.729,1.573 5.302,1.74 0.573,0.167 10 false GAMT 0.313,0.25 0.625,0.448 0.313,0.198 10 false *a 3.573,0.229 3.885,0.427 0.313,0.198 10 false *b 1.427,1.563 1.875,1.708 0.448,0.146 10 false AMT 2.344,1.563 2.792,1.708 0.448,0.146 10 false GAMT
*a Front view of wire harness connector
(Stack Wire)
*b Front view of wire harness connector
(to FC Control ECU)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB1,B1)Location & Routing

Click Connector(BB1)Engine Compartment>No. 2 Stack Wire>Stack Wire and No. 2 Stack Wire

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

BB1-13 (AMT) - B1-110 (AMT) Ignition switch off Below 1 Ω
BB1-14 (AMTG) - B1-111 (GAMT) Ignition switch off Below 1 Ω
BB1-13 (AMT) or B1-110 (AMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
BB1-14 (AMTG) or B1-111 (GAMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B1 FC control ECU connector.


b.

Reconnect the BB1 stack wire connector.



OK

5.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1D7A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.CHECK HARNESS AND CONNECTOR (STACK WIRE - FC AIR COMPRESSOR WITH MOTOR ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (STACK WIRE - FC AIR COMPRESSOR WITH MOTOR ASSEMBLY)

Pre-procedure1

a.
A481468

Disconnect the BB1 stack wire connector.


b.
A480856

Disconnect the B24 FC air compressor with motor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A481497C01
0.271,0.656 0.719,0.948 0.448,0.292 4.125,0.719 4.604,1.021 0.479,0.302 5.458,0.979 5.188,1.396 true 5.479,0.875 5.865,1.354 true 1.396,0.823 1.021,1.427 true 1.563,0.823 1.833,1.417 true 0.375,0.729 0.833,0.927 0.458,0.198 10 false BB1 4.24,0.792 4.552,0.99 0.313,0.198 10 false B24 5.854,1.438 6.313,1.635 0.458,0.198 10 false AMT 0.677,1.438 1.292,1.635 0.615,0.198 10 false GAMT 4.865,1.438 5.479,1.635 0.615,0.198 10 false AMTG 1.833,1.438 2.448,1.635 0.615,0.198 10 false AMT 0.271,0.198 0.573,0.385 0.302,0.188 10 false *a 4.125,0.219 4.427,0.406 0.302,0.188 10 false *b
*a Front view of wire harness connector
(Stack Wire)
*b Front view of wire harness connector
(to FC Air Compressor with Motor Assembly)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB1,B24)Location & Routing

Click Connector(BB1)Engine Compartment>No. 2 Stack Wire>Stack Wire and No. 2 Stack Wire

Click Connector(B24)Engine Compartment>No. 2 Stack Wire>FC Air Compressor with Motor Assembly

BB1-13 (AMT) - B24-4 (AMT) Ignition switch off Below 1 Ω
BB1-14 (GAMT) - B24-8 (AMTG) Ignition switch off Below 1 Ω
BB1-13 (AMT) or B24-4 (AMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
BB1-14 (GAMT) or B24-8 (AMTG) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B24 FC air compressor with motor assembly connector.


b.

Reconnect the BB1 stack wire connector.



OK

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY (FC AIR COMPRESSOR MOTOR TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.
A481468

Disconnect the BB1 stack wire connector.


Procedure1

a.
A481501C01
0.177,0.958 0.677,1.292 0.5,0.333 1.885,1.813 1.5,1.104 true 0.969,1.792 1.333,1.104 true 0.167,0.188 0.479,0.385 0.313,0.198 10 false *a 0.313,1.042 0.771,1.24 0.458,0.198 10 false BB1 1.833,1.833 2.292,2.031 0.458,0.198 10 false AMT 0.646,1.833 1.104,2.031 0.458,0.198 10 false GAMT
*a Front view of wire harness connector
(Stack Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB1)Location & Routing

Click Connector(BB1)Engine Compartment>No. 2 Stack Wire>Stack Wire and No. 2 Stack Wire

BB1-13 (AMT) - BB1-14 (GAMT) Ignition switch off 55.1 to 68.5 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the BB1 stack wire connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

8.CHECK FC AIR WITH MOTOR COMPRESSOR ASSEMBLY (FC AIR COMPRESSOR MOTOR TEMPERATURE SENSOR)
8.CHECK FC AIR WITH MOTOR COMPRESSOR ASSEMBLY (FC AIR COMPRESSOR MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.
A480856

Disconnect the B24 FC air compressor with motor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B24)Location & Routing

Click Connector(B24)Engine Compartment>No. 2 Stack Wire>FC Air Compressor with Motor Assembly

B24-4 (AMT) - B24-8 (AMTG) Ignition switch off 55.1 to 68.5 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B24 FC air compressor with motor assembly connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO.2 STACK WIRE - FC AIR COMPRESSOR WITH MOTOR ASSEMBLY)

NG

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY (FC AIR COMPRESSOR MOTOR TEMPERATURE SENSOR)