Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1D7A11  FC Air Compressor Motor Temperature Sensor Circuit Short to Ground  P1D7A15  FC Air Compressor Motor Temperature Sensor Circuit Short to Battery or Open  


DESCRIPTION

Refer to the description for DTC P1D7A1C.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1D7A1C

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D7A11 FC Air Compressor Motor Temperature Sensor Circuit Short to Ground Short to ground in the FC air compressor motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

FC control ECU

·

FC air compressor with motor assembly (FC air compressor motor temperature sensor)


Master Warning:
Comes on
EV A
P1D7A15 FC Air Compressor Motor Temperature Sensor Circuit Short to Battery or Open Open or short to +B in the FC air compressor motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

FC control ECU

·

FC air compressor with motor assembly (FC air compressor motor temperature sensor)


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P1D7A11 FC Air Compressor Motor Temperature
P1D7A15

HINT:

After confirming that DTC P1D7A11 or P1D7A15 is output, use the GTS to check "FC Air Compressor Motor Temperature" in the Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to ground


WIRING DIAGRAM

A337543E02
1.885,1.177 2.344,1.375 0.458,0.198 10 false AMT 1.802,1.875 2.26,2.073 0.458,0.198 10 false AMTG 2.292,1.896 2.75,2.094 0.458,0.198 10 false 8 2.292,1.188 2.771,1.396 0.479,0.208 10 false 4 4.521,1.177 5,1.385 0.479,0.208 10 false 110 4.531,1.938 5.01,2.146 0.479,0.208 10 false 111 4.865,1.177 5.323,1.375 0.458,0.198 10 false AMT 4.865,1.948 5.323,2.146 0.458,0.198 9 false GAMT 5.063,2.677 5.521,2.875 0.458,0.198 10 false B1 0.552,2.719 1.01,2.917 0.458,0.198 10 false B24 3.5,2.438 3.958,2.635 0.458,0.198 10 false BB1 0.552,2.896 3.042,3.51 2.49,0.615 10 false FC Air Compressor with Motor Assembly (FC Air Compressor Motor Temperature Sensor) 5.073,2.854 6.156,3.073 1.083,0.219 10 false FC Control ECU 3.073,1.188 3.552,1.396 0.479,0.208 10 false 13 3.052,1.948 3.51,2.146 0.458,0.198 10 false 14 3.896,1.917 4.354,2.115 0.458,0.198 10 false 14 3.896,1.177 4.375,1.385 0.479,0.208 10 false 13 5.958,1.292 6.417,1.49 0.458,0.198 10 false ADC 3.313,2.604 4.594,2.906 1.281,0.302 10 false Stack Wire

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 5 seconds or more.

2.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

3.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (FC CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1F089F

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed to FC stack assembly and EV battery.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A480856

Check the connector connections and contact pressure of the relevant terminals for the FC air compressor with motor assembly connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



Post-procedure1

a.

None.



A

4.READ VALUE USING GTS (FC AIR COMPRESSOR MOTOR TEMPERATURE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (FC AIR COMPRESSOR MOTOR TEMPERATURE)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
FC Air Compressor Motor Temperature
50003 397 1038
Result:
Result Proceed to
The value of FC Air Compressor Motor Temperature is -40 °C A
The value of FC Air Compressor Motor Temperature is 130 °C B
None of the above conditions are met C


HINT:
·

-40°C = -40°F

·

130°C = 264°F




Post-procedure1

a.

Turn the ignition switch off.



A

5.READ VALUE USING GTS (CHECK FOR OPEN)

B

8.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

C

5.READ VALUE USING GTS (CHECK FOR OPEN)

Pre-procedure1

a.
A481468

Disconnect the BB1 stack wire connector.


b.
A481500C01
0.188,0.906 0.708,1.323 0.521,0.417 1.646,1.75 1.896,1.188 true 2.292,1.729 2.042,1.177 true 0.167,0.188 0.479,0.385 0.313,0.198 10 false *a 0.323,1.042 0.781,1.24 0.458,0.198 10 false BB1 1.344,1.76 1.802,1.958 0.458,0.198 10 false AMT 2.323,1.76 2.781,1.958 0.458,0.198 10 false GAMT
*a Front view of wire harness connector
(Stack Wire)


Connect terminals BB1-13 (AMT) and BB1-14 (GAMT) of the stack wire connector.


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
FC Air Compressor Motor Temperature
50003 397 1038
OK:
Tester Display Condition Specified Condition
FC Air Compressor Motor Temperature Terminals BB1-13 (AMT) and BB1-14 (GAMT) connected
Ignition switch ON
130°C (264°F)


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the stack wire connector.



OK

6.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (STACK WIRE - FC CONTROL ECU)
6.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

Pre-procedure1

a.
A480856

Disconnect the B24 FC air compressor with motor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B24)Location & Routing

Click Connector(B24)Engine Compartment>No. 2 Stack Wire>FC Air Compressor with Motor Assembly

B24-4 (AMT) - B24-8 (AMTG) Ignition switch off 55.1 to 68.5 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B24 FC air compressor with motor assembly connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 STACK WIRE - FC AIR COMPRESSOR WITH MOTOR ASSEMBLY)

NG

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY (FC AIR COMPRESSOR MOTOR TEMPERATURE SENSOR)

7.CHECK HARNESS AND CONNECTOR (STACK WIRE - FC CONTROL ECU)

Pre-procedure1

a.

Disconnect the BB1 stack wire connector.


b.

Disconnect the B1 FC control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A481498C01
0.438,0.792 0.885,1.125 0.448,0.333 3.531,0.771 3.969,1.073 0.438,0.302 4.49,1.125 4.146,1.531 true 4.563,1.135 4.927,1.531 true 1.948,0.99 1.625,1.542 true 2.063,0.99 2.427,1.531 true 0.542,0.875 1,1.073 0.458,0.198 10 false BB1 3.688,0.844 4,1.042 0.313,0.198 10 false B1 3.99,1.563 4.438,1.708 0.448,0.146 10 false AMT 4.729,1.573 5.302,1.74 0.573,0.167 10 false GAMT 0.313,0.25 0.625,0.448 0.313,0.198 10 false *a 3.573,0.229 3.885,0.427 0.313,0.198 10 false *b 1.427,1.563 1.875,1.708 0.448,0.146 10 false AMT 2.344,1.563 2.792,1.708 0.448,0.146 10 false GAMT
*a Front view of wire harness connector
(Stack Wire)
*b Front view of wire harness connector
(to FC Control ECU)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB1,B1)Location & Routing

Click Connector(BB1)Engine Compartment>No. 2 Stack Wire>Stack Wire and No. 2 Stack Wire

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

BB1-13 (AMT) - B1-110 (AMT) Ignition switch off Below 1 Ω
BB1-14 (AMTG) - B1-111 (GAMT) Ignition switch off Below 1 Ω
BB1-13 (AMT) or B1-110 (AMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
BB1-14 (AMTG) or B1-111 (GAMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B1 FC control ECU connector.


b.

Reconnect the BB1 stack wire connector.



OK

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY (FC AIR COMPRESSOR MOTOR TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY - FC CONTROL ECU)

8.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

Pre-procedure1

a.
A480856

Disconnect the B24 FC air compressor with motor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B24)Location & Routing

Click Connector(B24)Engine Compartment>No. 2 Stack Wire>FC Air Compressor with Motor Assembly

B24-4 (AMT) - B24-8 (AMTG) Ignition switch off 55.1 to 68.5 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B24 FC air compressor with motor assembly connector.



OK

9.CHECK HARNESS AND CONNECTOR (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY - FC CONTROL ECU)

NG

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY (FC AIR COMPRESSOR MOTOR TEMPERATURE SENSOR)

9.CHECK HARNESS AND CONNECTOR (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY - FC CONTROL ECU)

Pre-procedure1

a.
A480856

Disconnect the B24 FC air compressor with motor assembly connector.


b.

Disconnect the B1 FC control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A481499C01
0.625,0.729 1.135,1.115 0.51,0.385 3.573,0.76 3.969,1.063 0.396,0.302 1.906,0.938 1.25,1.344 true 1.885,1.021 2.25,1.292 true 4.5,1.125 3.927,1.469 true 4.563,1.135 4.875,1.448 true 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a 3.625,0.156 3.938,0.354 0.313,0.198 10 false *b 1.115,1.385 1.573,1.583 0.458,0.198 10 false AMT 2.115,1.344 2.729,1.542 0.615,0.198 10 false AMTG 3.792,1.51 4.25,1.708 0.458,0.198 10 false AMT 4.74,1.49 5.354,1.688 0.615,0.198 10 false GAMT 0.771,0.844 1.229,1.042 0.458,0.198 10 false B24 3.708,0.844 4.021,1.042 0.313,0.198 10 false B1
*a Front view of wire harness connector
(to FC Air Compressor with Motor Assembly)
*b Front view of wire harness connector
(to FC Control ECU)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B24,B1)Location & Routing

Click Connector(B24)Engine Compartment>No. 2 Stack Wire>FC Air Compressor with Motor Assembly

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

B24-4 (AMT) - B1-110 (AMT) Ignition switch off Below 1 Ω
B24-8(AMTG) - B1-111(GAMT) Ignition switch off Below 1 Ω
B24-4 (AMT) or B1-110 (AMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
B24-8 (AMTG) or B1-111 (GAMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B1 FC control ECU connector.


b.

Reconnect the B24 FC air compressor with motor assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR