Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P222F62  Barometric Pressure Sensor "A"/"B" Correlation Signal Compare Failure  


DESCRIPTION

The EV control ECU performs control to conform to the vehicle usage conditions by sensing the atmospheric pressure by the atmospheric pressure sensor installed to the circuit board of the motor generator control ECU (MG ECU), which is built inside the inverter assembly with converter. The EV control ECU also detects deviations in the monitored values of the atmospheric pressure sensors, between the one inside the EV control ECU and the other one inside the FC control ECU and determines whether a malfunction has occurred.

A478519E01
0.875,0.688 2.75,1.135 1.875,0.448 10 false EV Control ECU 0.75,1.5 2.771,1.781 2.021,0.281 10 false Atmospheric Pressure Sensors 4.521,1.677 6.479,1.896 1.958,0.219 10 false Atmospheric Pressure Sensors 4.594,1.021 6.385,1.479 1.792,0.458 10 false Motor Generator Control ECU (MG ECU) 4.417,0.583 6.438,0.823 2.021,0.24 10 false Inverter with Converter Assembly 0.771,3.25 2.625,3.51 1.854,0.26 10 false Serial Communication Line

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P222F62 Barometric Pressure Sensor "A"/"B" Correlation Signal Compare Failure When the difference between the atmospheric pressure values of the atmospheric pressure sensor in the inverter with converter assembly and EV control ECU is a constant value or more and the identical conditions are met even after 3 hours have elapsed
(1 trip detection logic)
·

Inverter with converter assembly

·

EV control ECU


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P222F62
·

Atmospheric Pressure

·

Atmospheric Pressure (MG)



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

When the ignition switch is turned to ON, if the Data List item "Atmospheric Pressure" and "Atmospheric Pressure (MG)" are approximately the same value, the condition is normal.

2.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

3.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P222F62 and microcomputer malfunction of hybrid control system DTCs in the table below are output A
P222F62 and powersource circuit malfunction of hybrid control system DTCs in the table below are output B
P222F62 and Ccommunication system malfunction of hybrid control system DTCs in the table below are output C
P222F62 and sensor and actuator circuit malfunction malfunction of hybrid control system DTCs in the table below are output D
P222F62 and sensor and actuator circuit malfunction malfunction of c DTCs in the table below are output E
P222F62 only is output, or DTCs except the ones in the table below are also output. F
Only P222F62 is output G

Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060B1C Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range
P060B71 Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P1D0400 FC Air Compressor Motor Control Module A/D Processing Performance
Power source circuit malfunction Hybrid control system P06881F ECM/PCM Power Relay Sense Circuit Intermittent
P1C731C Sensor Reference Voltage "H" Circuit / Open Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid / EV Control Module Missing Message
P1E3B87 Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message
Sensor and actuator circuit malfunction FC control system P222A12 Barometric Pressure Sensor "B" Circuit Short to Battery
P222A14 Barometric Pressure Sensor "B" Circuit Short to Ground or Open
Hybrid control system P222612 Barometric Pressure Sensor "A" Circuit Short to Battery
P222614 Barometric Pressure Sensor "A" Circuit Short to Ground or Open


HINT:

P222F62 may be stored due to a malfunction which causes the DTCs in the preceding table to be stored. In this case, first troubleshoot the output DTCs in the preceding table.



Post-procedure1

a.

Turn the ignition switch off.



A

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

D

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

E

F

2.READ VALUE USING GTS (ATMOSPHERIC PRESSURE, ATMOSPHERIC PRESSURE(MG))

G

2.READ VALUE USING GTS (ATMOSPHERIC PRESSURE, ATMOSPHERIC PRESSURE(MG))
2.READ VALUE USING GTS (ATMOSPHERIC PRESSURE, ATMOSPHERIC PRESSURE(MG))

Pre-procedure1

a.

Using the table, read the normal atmospheric pressure value for the applicable altitude.

A250945

HINT:
·

Standard atmospheric pressure is approximately 101 kPa (15 psi).

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.1 psi). This varies by weather.




Procedure1

a.

Compare the Atmospheric Pressure and Atmospheric Pressure (MG) values in the Data List with the normal atmospheric value from the table.

Powertrain > EV > Data List
Tester Display
Atmospheric Pressure
Atmospheric Pressure (MG)
50003 397 888,797
OK:

The difference between the value for Data List item "Atmospheric Pressure" or "Atmospheric Pressure(MG)"and the normal atmospheric pressure value is 10 kPa or less.


Result:
Result Proceed to
Difference between "Atmospheric Pressure(MG)" in Data List and normal atmospheric pressure value is 10 kPa (1.5 psi) or more. A
Difference between "Atmospheric Pressure" in Data List and normal atmospheric pressure value is 10 kPa (1.5 psi) or more. B
Other than above. C



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

C